the crane lift on scale, so with this block fully reeved we can lift 40kg. 4kg on single wire
@RMWtechnoscalemodels
10 жыл бұрын
Helaas hebben we de stempelpoten niet bedienbaar /werkend kunnen krijgen. Als we met volle last over een poot draaien staat er 83 kg druk op. De afmeting van de kokerbalk is zo klein dat alleen de dunne hydrauliekslangen van Leimbach de buigradius in de balk aan kunnen. Helaas kunnen deze de enorme druk niet aan.
10 жыл бұрын
Tolles Video. Sehr schöner Kran.
@RMWtechnoscalemodels
10 жыл бұрын
you can order / buy one at E-bay in scale 1:50
@MANIARC
10 жыл бұрын
very very very very good!!!
@Truckingmad01
10 жыл бұрын
Hiya, awesome cranes. How did you construct the boom and work out the hydraulic rams for raising the jibb. I'm working on designing the LTM11200-9.1 mobile crane.
@RMWtechnoscalemodels
10 жыл бұрын
The boom is made from stainless steel and the hydraulic cilinders I design my self. Because of the weight of the boom we need 50 bar to push up the boom. So try to keep your weight of the boom down to a minimum ;-)
@Truckingmad01
10 жыл бұрын
Hiya, ok cool. I was thinking of making the hydraulic rams using brass and threaded rod so it unwinds to lift boom and screws in to lower. How did you secure the kingpin on the main turret to stop it from bending so it can rotate. I was thinking of putting a drive motor ( 550 size brushed) on the drive axles. What drive power would you recommend being the vehicle length being about 36 inches.
@RMWtechnoscalemodels
10 жыл бұрын
Truckingmad01 please send an e-mail by my website [contact]
@Truckingmad01
10 жыл бұрын
Ok will do thanks. :-)
@andrealmeida6008
9 жыл бұрын
Truckingmad01 muinto bom mesmo.vc sao os ninja.
@redwolfrc1.14
3 жыл бұрын
Fantastic. In line for an order
@davegraham1987
7 жыл бұрын
Nice
@dennis17ish
10 жыл бұрын
dat is wel jammer ja maar zoveel ruimte heb je niet in een stempelbalk om er iets in te stoppen kan je de ballast van 50kg er wel aanhangen aan de bovenwagen hydraulisch
@yoski203
10 жыл бұрын
aaaaaahhh!! hook it up!!!
@dennis17ish
10 жыл бұрын
mooi gemaakt wat is het maximale wat hij kan oppakken en de mast is de mast gemaakt van 1mm staal dikte
@roypatterson9910
6 жыл бұрын
Where can I buy one of these cranes and how much does it cost???
@roypatterson9910
6 жыл бұрын
And how much weight can it lift?
@freddyanderson94
6 жыл бұрын
Como puedo comprar y el precio por favor
@katherinemamani9041
9 жыл бұрын
Donde puedo comprar de estas máquinas? ??
@dennis17ish
10 жыл бұрын
gaat de stempels naar beneden door een electromotor in de stempel en een spindel zo ja is deze in staat om de kraan van 75 kg van de grond af te krijgen
@RMWtechnoscalemodels
10 жыл бұрын
wordt nog aan gewerkt ;-)
@dennis17ish
10 жыл бұрын
oke is de kraan nog ergens te zien dit jaar op een beurs
@kimlyon5924
9 жыл бұрын
where can i get one
@fanieels1858
8 жыл бұрын
Hi Are these machines available to bay and where please don't ignore this mail
@RMWtechnoscalemodels
8 жыл бұрын
+Fanie Els No, the cranes are self build, you can not buy them. Check the website and see with your own eyes. ;-)
@roypatterson9910
7 жыл бұрын
RMWtechnoscalemodels Are you trying to tell us that you built this crane from scratch, that you built every single part on it, and that it's not a kit anyone else can build but only you?
@RMWtechnoscalemodels
7 жыл бұрын
If you have checked my website you have seen fases of the build of the crane.The only things I bought where the electro motors, tires, bearings, rope and parts of the electronics for the radio controle.It is NOT a kit you can buy in a store.
@RMWtechnoscalemodels
10 жыл бұрын
voor demo`s check mijn website of de agenda van MBVP mbvpforum.nl/viewforum.php?f=67&sid=44006ffea5630642d4fe0ba26d002841
Пікірлер: 33