Thank you So much as I have continued to struggle in properly securing the bulb until now.
@varunbawa3903
Ай бұрын
Thnks buddy you made my life easy
@BunniiBlossomBleum
3 жыл бұрын
Thank you!! Total life saver 🌸
@TheJoeDohn
Жыл бұрын
Wow very well done. The camera through the hole in the sidewall.... Thnk you sir
@dave8319
5 жыл бұрын
Thanks for saving me some money. I have one comment though. When you are saying turn the driver's side headlight ignitor "toward" the engine block, I understood this to mean turn the thing clockwise it the assembly, i.e., turning the top of the igniter toward the engine. After trying this unsuccessfully for a while and doing some other research I realized that you turn it counter clockwise, as in "lefty-loosie." It came right out. (I'm assuming from your accent that this is not a right-hand-drive car :-)) It went back in the same way. Also, I didn't get the Philips OEM, as the price was eye-watering. I got a Chinese version on Amazon, which seems to work fine so far. Even if it fails early, I could get three of these for the cost of one Philips bulb and then go Chipotle.
@jtblazeltw
5 жыл бұрын
Hey Dave glad it helped, yes counter clock wise to get it out and clock wise to install, the connector to the back of the bulb is on the bottom hence the reason I stated "turn the connector toward the engine block" but same idea. I have had mixed results with Amazon bulbs but hope it works out for you.
@Hellomarie2003
8 жыл бұрын
We took it to a shop were they install lights, radios, etc and the idiots installed it backwards and a AFS light came on so that's when we decided to try it again. Will try your suggestion. Thank you for your prompt response.
@Nodstar73
7 жыл бұрын
Thanks you just saved me £200.
@k.o.7405
2 жыл бұрын
You made it so easy,
@jtblazeltw
8 жыл бұрын
hellomarie, make sure you feel the bulb seat in correctly before twisting it back to the upright/correct position. sounds like the tabs may not be engaging into the housing slots.
@corypage
8 жыл бұрын
Awesome. Thanks a lot!
@mikesix1
4 жыл бұрын
Thank you 🙏🏾 god bless bro
@davidberschneider8942
5 жыл бұрын
Hi J Watkins, thank you for this video. I tried this replacement myself on my 2014 CC according to your video and everything worked quite well. However the headlights now show a very uneven illumination, meaning that there is no sharp border between light and dark and in the illumated area there are spots that are brighter and darker. What could I have done wrong in the installation of the new bulbs? Maybe I didn't rotate them far enough? The bulbs were very hard to loosen and tighten and I was glad that I could even rotate them around 10 or 15 degrees.
@jtblazeltw
5 жыл бұрын
Carefully try to rotate new bulb into original bulb orientation, I would also recommend you remove the new bulb first and make sure you didn't pull/wrap one of the small gauge black servo wires around the bulb. Those are the only things that come to mind.
@citesc80
8 жыл бұрын
Thank You! :)
@wiltonrooks
8 жыл бұрын
Thank you for the very good video. No one else has one as good. I have a question. My left headlamp on 2014 CC Rline burned out. I replaced both sides with new Philips Xtreme HID D3S. Low beam works find on both. High beam only works on the right side. I put another HID D3S in left side and it only worked on low beam also. Is there a fuse that controls just the highbeam circuit on the left side. Fuse box is not labeled. Your help appreciated.
@jtblazeltw
5 жыл бұрын
Sorry for the very delayed response. The high and low beam are the same bulb. Sounds like you have a shutter issue with your headlight which is a solid on its own circuit
@SeanKayGee
4 жыл бұрын
My high beams aren’t working. The blue light doesn’t even come on when you push or pull the switch. Any ideas? It’s all done with 1 bulb because it’s Bi-xenon right?
@hidconceptcom
6 жыл бұрын
good video.
@MahoCan2158
4 жыл бұрын
Thank you bro
@MrBoomtheroom
2 жыл бұрын
my bulb ( the inner non hid bulb ) doesnt work is it easy to replace that one? whats it for anyway only comes on when u pull outward on the headlight switch
@jaychen2000metal
5 жыл бұрын
My '14 is set up a bit differently. I can barely fit my hand in there 😐
@sagzy8383
7 жыл бұрын
ive been trying to do this on my cc but the it doesnt nudge or move the mechanic says for him to do a proper job he'll have to take out the headlight whats your thoughts?
@jtblazeltw
7 жыл бұрын
Sagzy 83 if your unable to get it, sometimes it can be tricky/corroded, you will have to remove bumper in order to get the whole headlight assembly out to service the bulb.
@chocoboxx1586
4 жыл бұрын
Thanks bro
@killyamomz
4 жыл бұрын
This is such a pain, still havent been able to get my replacement bulb in there
@MyMattinthehat
2 жыл бұрын
Mine is the same set up but has a hose clamp (got a decent video of it) and it does not simply twist off. I'm 100% sure I need to remove that clamp before I can twist. At this point, considering just letting a vw mechanic deal with it...
@zakariaabidi
5 жыл бұрын
Hi thank you for the video, can you share the link for the product ? I need to buy a new one but I don't know if it's 4000 or 6000. Thans in advance
@jtblazeltw
5 жыл бұрын
To match OEM this will match: www.amazon.com/OSRAM-SYLVANIA-High-Intensity-Discharge/dp/B00265FWIC/ref=mp_s_a_1_1?keywords=sylvania+d3s&qid=1560902435&s=gateway&sr=8-1
@asalazar40
7 жыл бұрын
Do you have a video on replacing the DRL lights??? I found a few but my 2013 VW CC Sport does NOT have a plastic shield to access from under the fender liner. SOS...help! Thanks :)
@jtblazeltw
7 жыл бұрын
asalazar40 13+ CC's use LED DRL's to my knowledge they are not serviceable, pre 13 MY should just be high beam bulb is DRL
@martobrowser1383
3 жыл бұрын
@@jtblazeltw CC's use also Halogen DRL's on normal Bixenon headlights. LED DRL's are on the Bixenon headlights with curving function.
@ionelfona1625
5 жыл бұрын
How much force does it usually require to twist the bulbs? I tried to twist mine on my Passat 2012 Estate and didn't manage...
@ionelfona1625
5 жыл бұрын
Or maybe it isn't the same procedure?
@stipojukic6744
2 жыл бұрын
Does it fit DS??
@lalmasjidkamolvi8052
5 жыл бұрын
hi ive passat cc 64 plate the right headlight goes off after few minutes and immediately back on, its been doing this for 2 weeks now. any solution for this thanks ?
@jtblazeltw
5 жыл бұрын
Never had this issue, first thing that comes to mind would be a ballast, the best way to diagnose it would be to scan for fault codes in the headlight module
@aaronjesse4312
5 жыл бұрын
Do you happen to know where the ballast is on these? Mine needs replaced...
@jtblazeltw
5 жыл бұрын
I have not removed one, but it's on the bottom of the headlight assembly below the HID bulb held in with 3 screws. Driver side might be able to get at via wheel well. As for passenger side I bet the washer bottle is in the way, might require a bumper pull to remove headlight assembly.
@gedDous514
Жыл бұрын
Hi what are the bulb sizes of all the lights in the headlight unit? I have the same ones thank you
@jtblazeltw
Жыл бұрын
If you are looking for a complete guide I would suggest using this bulb guide, it will cover all serviceable bulbs on the entire vehicle. www.sylvania-automotive.com/bulb-finder.html
@Frmoside760
4 жыл бұрын
Mine is on the passenger side I’m twisting toward the fender but it’s not budging , what should I do ?
@flykidsutton22
3 жыл бұрын
Mine is too ! It’s not working
@Frmoside760
3 жыл бұрын
@@flykidsutton22 I might of done a little too much but I had to take grill and bumper off just on the side to take out the headlamp and take out the bulb , messed up part was I was able to jus twist off the other side 😂😂
@carlibell9288
5 жыл бұрын
Hi! So we replaced the low beam lights today and the low beam lights still will NOT come on. Both of the low beam lights were replaced. The car still reads the error message on the dash “check right (and left) low beam lights”. What should we do? Also how many sets of low beams on the car? Is there something on the car that needs to be reset once the lights are replaced?
@jtblazeltw
5 жыл бұрын
There is only one set of low beam lights on a car if I am understanding the question correctly. I would recommend you consult your owners manual for the fuse location for the headlights. Start by checking that the fuses are good.
@carlibell9288
5 жыл бұрын
J Watkins thanks for replying! Our mechanic checked the fuses once he installed the new bulbs and said they were fine.
@jtblazeltw
5 жыл бұрын
@@carlibell9288since the fuses are good, few things that come to mind, ensure the headlight harness is connected all the way. Ensure the wire harness is connected to the back of the bulb and ballast. If that doesn't do it might be something with power coming into the ballast or power leaving the ballast. Good luck.
@carlibell9288
5 жыл бұрын
J Watkins one more question, do you know what fuse in the fuse box controls the low beams? We couldn’t find which one it is in the manual.
@jtblazeltw
5 жыл бұрын
@@carlibell9288 I am not where I can get to my manuals but Im pretty sure the fuse diagram is in the tips and advice booklet.
@amilca123
4 жыл бұрын
Can you help figure out why my led drls are not turning on
@jtblazeltw
4 жыл бұрын
They only time I ever tinkered with the DRL's was via vagcom as there is an led option check box in the coding under group 55. I haven't had this problem; things that come to mind would be control board, wire connections inside the headlight, headlight wire harness connector or even possible something with the parking break, since they are off if parking brake is on. Start with the easy stuff by checking wire connections. Wish I had more info- good luck.
@jayg5888
3 жыл бұрын
Having the same issue.
@rondeledwards
2 жыл бұрын
The daytime running led on the left side of my cc don’t work and I can’t find a video anywhere which explains this and everyone keeps telling my I just need to replace the whole light
@jtblazeltw
2 жыл бұрын
Hey Rondel, I have not had this issue yet but I did take a quick look at it. From what I can tell the ribbon cable (red arrows) as shown in the images below are not serviceable. The only way you will be able to replace the entire LED DRL assembly is to separate the headlight assembly from the lens. That said; it might still be worth checking to ensure something didn’t work itself loose. The ribbon cable connections can be seen after you remove the dust covers on the rear of the headlight and the cornering bulb service dust cover. I tried to get you the best images I could as it’s a very tight space. If you are able to check all the ribbon cable connections and the DRL is still not working, then you will need to replace the entire headlight assembly which even used can be on the pricey side. Another option would be to explore how to disable LED DRL, via dealer of VAGCOM. Best of luck. photos.app.goo.gl/hNKZ232fisP5HaU99
@rondeledwards
2 жыл бұрын
@@jtblazeltw thank you for your response. I will check on the connection tomorrow.
@thebigbosss1000
2 жыл бұрын
What brand are those bulbs?? My right side went out , I checked Autozone and they have some that go for $179 each
@jtblazeltw
2 жыл бұрын
OSRAM is OEM D3S about $60 each on Amazon, local stores may be higher.
@thebigbosss1000
2 жыл бұрын
@@jtblazeltw thank you I’ll check them out
@stanblackwell213
11 күн бұрын
My bulb D3S 35W bulb blew out during the smog check and my car wouldn't start, so the smog check guy jumped started my car and I went to AutoZone to get the battery charged on my 2013 VW CC Lux. Then I attempted to buy a bulb and AutoZone said it was $131.99 just for 1 bulb and I was in shock. So I went on Temu and found the same bulbs 2 for $10.95 and I immediately ordered them and they are being shipped from a local warehouse. AutoZone are ripping people off with those outrageous high prices
@BK-qu2tk
Жыл бұрын
Anyone knows which bulb i should use for cornering lights?
@jtblazeltw
Жыл бұрын
H7 55W kzitem.info/news/bejne/mZV9q31-fJShlaA
@tylermiller5189
6 жыл бұрын
I got the bulb out (with medium resistance). But not the oem or my replacement bulb are not turning back into the correct postion when installing them, there is A HUGE resistance.
@jtblazeltw
6 жыл бұрын
Tyler Miller as long as the pins on the bulb are aligned with the socket and your turning in the correct direction it will go, double check all above and take your time it can be a bit tough at times, best of luck
@jtblazeltw
6 жыл бұрын
Tyler Miller also make sure the bulb is seating in the socket properly before trying to twist bulb into place
@tylermiller5189
6 жыл бұрын
J Watkins ok. I will try first thing in the morning. Ill tell you how it went
@tylermiller5189
6 жыл бұрын
J Watkins I installed it without attaching the cord, then I installed the cord. I did this to get more leverage
@jtblazeltw
6 жыл бұрын
Tyler Miller good deal glad you got installed
@Hellomarie2003
8 жыл бұрын
Yeah. We tried it again and it pops back out.
@falsedoctrinekilla
3 жыл бұрын
Turn it towards the fender not the engine block, for an easier angle take off the tire and panel
Online or your local auto parts store will have them..I would recommend Osram D3S 35W bulbs.
@thsims79
6 жыл бұрын
Where is the low beam bulb found? Is it the HID?
@jtblazeltw
6 жыл бұрын
thsims79 yes the high and low beam are the same bulb (HID). High beam is just a shutter that is lifted out of the path of the bulb.
@chiragmohanty1755
5 жыл бұрын
@@jtblazeltw what's the bulb number .... H7?
@jtblazeltw
5 жыл бұрын
Bulb number is D3S on VW CC hid fog light is an H8
@chiragmohanty1755
5 жыл бұрын
J Watkins thanks a heap 👏🏻
@yasseralghamdi9890
7 жыл бұрын
is the bulb 4000k or 6000k ?
@jtblazeltw
7 жыл бұрын
I am not sure i would guess since they are stock bulbs they would be closer to 4000k. maybe 4800k. I ue the Philips DS3 Original Equipment bulb.
@jaychen2000metal
5 жыл бұрын
My '14 is set up a bit differently. I can barely fit my hand in there 😐
@jaychen2000metal
5 жыл бұрын
Yasser Alghamdi I just bought some 6,000, they seem to be the purest of white according to a chart I found
@nickdemsey7188
3 жыл бұрын
Your the balls
@marsig4103
5 жыл бұрын
Passenger side won’t come out.
@funk6721
4 жыл бұрын
Thank you for this concise video. If I hadn't seen this clip I wouldn't have even tried this job. I did get stuck on the passenger side bulb at the point where you rotate the bulb assembly into place. Desperate and lacking the necessary hand strength I made a "wrench" to rotate the assembly into place. It worked. Here's the video: kzitem.info/news/bejne/mKepr3qMfoJze20
@jtblazeltw
4 жыл бұрын
Good info, thanks for sharing
@zeyadtatari4188
7 жыл бұрын
I tried to remove it in my cc 2013 but it doesnt pop up, it is so tight that I cant twist it. I see in your video how you remove very easily and I wish you can explain how to do that. Your video is the only one for the cc
@jtblazeltw
7 жыл бұрын
The first time it took it off it was a bit tight. Ensure you are rotating it the correct way. Should twist with no issue. Ensure light bulb has cooled down.
@zeyadtatari4188
7 жыл бұрын
I tried again and couldn't remove it although I applied more pressure, I am twisting the same direction in the video, I am thinking of using a tool
@tylermiller5189
6 жыл бұрын
what tool did you end up using to force it?
@dave8319
5 жыл бұрын
Try turning it counterclockwise wrt the housing, like you are unscrewing a normal cap. That worked for me. The motion is slight, and the thing is inherently a little jiggly, so it's bit hard to tell when it's loose or tight. Just get it move a bit and then pull it out. You don't have to move it far.
@barnabaas79
5 жыл бұрын
My ballast touched the fuse box and sparked out. The new headlights don't work so I'm fairly sure I fried that cable. =( That doesn't look like it's a very straight forward fix unfortunately.
@jtblazeltw
5 жыл бұрын
That's unfortunate did you have the cover off of the fuse box? The 12v + lugs on the front of the fuse box are very well covered. Not sure what issues it could cause, have you checked the fuses?
@barnabaas79
5 жыл бұрын
@@jtblazeltw Yea I have a 2013 Tiguan and space was super tight on the drivers side so I took the fuse cover off. For the extra space it gave me it wasn't worth this extra hassle now. Fuses seem fine but I'm going to go over them one by one later today just to double check.
@jtblazeltw
5 жыл бұрын
Okay makes sense, be sure to check the stud mount fuses on the front of the fuse box if tiguans have them.
@barnabaas79
5 жыл бұрын
@@jtblazeltw Hm, I didn't see any but I'll double check. Front just had the connection points. Every fuse was still good. =\
@eden20111
11 ай бұрын
1:45 wth is the igniter???
@jtblazeltw
11 ай бұрын
It's used to start the bulb, an ignitor provides a high-voltage pulse to the bulb, which creates a spark, ionizing xenon gas in the bulb, creating a conducting tunnel between the tungsten electrodes at the top and bottom of the glass tube. The ballast is located on the underside of the headlight housing.
@eden20111
11 ай бұрын
@@jtblazeltw the underside so it’s where the plug is?
@eden20111
11 ай бұрын
@@jtblazeltw I been at this for 2 hours trying to remove the bulb but it won’t budge. So now I gotta HOLD the underside where the plug is and twist?
@jtblazeltw
11 ай бұрын
@@eden20111 that's frustrating, I have seen people make custom tool out of wood for example to use as a wrench to get more leverage. I have never had an issue but this could depend on your location and the amount of corrosion. Best of luck to you.
@sylent6
3 жыл бұрын
The only painful part about all of this is the price. $297 for both HID bulbs.
@jehadgharib
2 жыл бұрын
Paid 35$ on EBay
@sylent6
2 жыл бұрын
@@jehadgharib that’s big ouch on me..lol. I end up getting an Arteon
@jehadgharib
2 жыл бұрын
@@sylent6 nah it’s ok man at least you got yours fixed too and didn’t pay the dealer price . Could have been even more expensive
@tj29er
2 жыл бұрын
2010 vw cc no need removing everything you stated at :20 seconds in. more room and easier than this...just so you know
Пікірлер: 109