You have a high level of automotive skill. Well done.
@TEAMR4ULTV
10 ай бұрын
Thanks for watching really appreciate it
@habibali3106
7 ай бұрын
VERY FASCINATING...HAVE 2010 MAZDA2. 75 BHP...HAD NO PROBLEMS TILL RECENTLY...CLUTCH SLIPPING NOW. 1ST/2ND GEAR....DONE 106.000 MILES TO DATE....ÇOST QUOTE AT GARAGES SEEMS TO BE ABOUT OVER £415..U MAKE IT LOOK SO EASY. AND U LOOK VERY CAPABLE AND A PROFESSIONAL MECHANIC...PITY U R NOT IN GLASGOW....ANYHOW ENJOYED UR VIDEO....A LIKE. THANKS
@TEAMR4ULTV
7 ай бұрын
Thanks for watching really appreciate it. I know would gave done it for you if you were local
@habibali3106
7 ай бұрын
Thanks for UR reply...This shows that U read UR viewers comments...Thanks...@@TEAMR4ULTV
@thelordgodisone
2 күн бұрын
Thank you for sharing this!!! Extremely helpful!
@thinks4himself
6 ай бұрын
Great video bud. Informative and straight to the point. In the middle of a earlier Mazda 2 clutch. It's a bit different but principle is the same.
@TEAMR4ULTV
6 ай бұрын
Thanks for watching really appreciate it
@peterwatson2165
9 ай бұрын
Very helpful thanks 👍
@waloodalwaffles6053
Жыл бұрын
Is it the same for a 2009 mazda 2?
@leonidassotiropoulos9618
7 ай бұрын
yes
@preneshpandoy8970
11 ай бұрын
Awesome.... Thanks mate. Appreciate it👌👌👌👍
@TEAMR4ULTV
11 ай бұрын
Thanks for watching really appreciate it
@southernatvriders2426
9 ай бұрын
The connector on the rear of the transmission next to the firewall above where the axles stick in is there a wire connected to the sensor or not
@rogerbarrett9920
9 ай бұрын
Nice job, but I always change the pilot bearing in the centre of the crankshaft at the same time.
@TEAMR4ULTV
9 ай бұрын
Thanks for watching really appreciate it
@sheroze877
Жыл бұрын
Amazing👌
@giffenjapeg9255
Жыл бұрын
I was willing to do this myself, until the engine stand part. Great video though man, cheers.
@TEAMR4ULTV
Жыл бұрын
👍
@boccamokg1829
Жыл бұрын
If you are doing it on the ground i guess you can put a jack, a wood block or jack stand there to support the engine.
@thinks4himself
6 ай бұрын
I use a motorbike jack, 2 jack stands and a trolley jack. Jack stands to support car, motorbike jack for motor and trolley jack to drop the trans and pull out and away from engine.
@trellosone
Жыл бұрын
Thank you!
@TEAMR4ULTV
Жыл бұрын
Thanks for watching really appreciate it
@andrewchung1838
Жыл бұрын
Thanks for the video. With the gearbox oil do you just keep putting in oil until it starts overflowing out of the fill hole? Cheers.
@TEAMR4ULTV
Жыл бұрын
Yes that's exactly what we do
@lovepreetsinghhanjra1997
Жыл бұрын
Nic video sir
@TEAMR4ULTV
Жыл бұрын
Thanks for watching really appreciate it
@ChristJohn-nm6pp
4 ай бұрын
ok I have this same car and my gears will not change into any gears when car is on but when its off it will change gears ? second question is what power tool will allow me to take off t=wheels ? and last when changing the slave cylinder does it require oil to be put in it and can the fly wheel be refurbish with sander ?? I just want to do this on my own as iv been high price on job
@jaytravel-12
Жыл бұрын
🎉u the man fam
@TEAMR4ULTV
Жыл бұрын
Thanks for watching really appreciate it
@ChristJohn-nm6pp
4 ай бұрын
also how much oil do i need to put back in transmission and how to fill it ?
@taichihead42
10 ай бұрын
How do you destroy a gearbox and clutch on a 2014 mazda. I suspect riding the clutch and leaving it in gear at traffic lights. Most people do it.
@TEAMR4ULTV
10 ай бұрын
Possibly that's right but I think on this occasion it's just wear and tear
@jaytravel-12
8 күн бұрын
anyone know how to reach and take off drive shaft nuts ??
@chrisstainer3090
Ай бұрын
Fuck that garage job for sure
@John.Skelton
Жыл бұрын
I GET SO MUCH ANXIETY WHEN I DO BIG PROJECTS LIKE THIS..... I'M ALWAYS WORK I'M GOING TO MESS SOMETHING UP EVEN WORSE AND DESTROY THE CAR EVEN MORE.....😢
@TEAMR4ULTV
Жыл бұрын
Dont worry about it take it easy. If you want try to follow my video and hopefully it will help you out. Hopefully.
@John.Skelton
Жыл бұрын
@@TEAMR4ULTV Absolutely! Thank you so much for the encouragment! 🙏😊
@jaytravel-12
5 ай бұрын
i for got to ask what all parts do i need including oils ?
@TEAMR4ULTV
5 ай бұрын
You need the clutch kit and I would recommend using ATF fluid instead of ep90 gear oil
@jaytravel-12
5 ай бұрын
@@TEAMR4ULTV thank brother you The best
@chiseen
Ай бұрын
Hey Raul! Still watching your video, is LUK the oem for this model?
@TEAMR4ULTV
Ай бұрын
I don't think so I think it's Asin or Exceedy but I prefer LUK
@sahrajevo
Жыл бұрын
did you changed the shaft sealing rings?
@TEAMR4ULTV
Жыл бұрын
No I didnt it wasn't leaking so just left it
@ice_rydaa
2 ай бұрын
Is this the same for 2004 Mazda 2?
@TEAMR4ULTV
2 ай бұрын
I think pretty much the same. Thanks for watching really appreciate it
Пікірлер: 48