Dude, this video was exactly what I was looking for. Perfect how to. Thank you.
@MrBerett315
5 жыл бұрын
Just bought a stock '14 model rzr 800s to fart around with. This was the most informative video I've found. Cheers mate!
@chuckstubblefield5998
5 жыл бұрын
Good work. Just a lil note, the heat in the clutch cover will be a lil hotter due to having the heat to travel further and restricting air flow. Addiing a attwood 3000 bilge blower on exhaust clutch cover side will fix heat issue. Also " blow hole" makes a good blower as well. They suck out the heat on the clutch exhaust side very well. God bless and enjoy
@robertharding3129
9 жыл бұрын
Can you make a list of parts that you used so that everyone can get it to make theirs??
@Poisonpowertrain
2 ай бұрын
yesss please
@trikerjon
4 жыл бұрын
Very good video, thanks for all the information including the dimensions of the pipe to make it. Great job 👍
@keyplayermark
3 жыл бұрын
Thanks for this video. I was wanting to add another air filter and figured I needed to do the snorkels. Great video. Been much easier with a parts list, but hey.. Kudos !
@gilbertochoa1553
4 жыл бұрын
looks really good. I'm going to use the exact same 45 to 90 to 45 cut. I've been looking for ideals for the tips. Im going to run a 4th pvc pipe and shove all my vents in there.
@NavigateOffroad
5 жыл бұрын
Well done. It looks like you took time to actually do it right and make it look good.
@mikepringle1104
7 жыл бұрын
great Video, well done and saved me a bunch of time figuring out parts and money buying them. I appreciate the time you put into the Video.
@pilotoelguapo
7 жыл бұрын
Looks good. I would radius the notch in you rear window the same as the radius of your PVC pipes so it doesn't crack at that 90 degree corner. I would also tap into the PVC pipe below the bed and attach the other small vents there. That will give you a much cleaner more professional look.
@MrFerrill
8 жыл бұрын
Awesome! Do you happen to have a list of the couplings, pipes and stuff needed? My main problem with projects like this is having to run back to home depo because I need something else
@x4x4offroad87
10 ай бұрын
Man I like the how-to video very very helpful I'm fixing to do that to my 2013 whole lot cheaper than going and buying the actual kit for $360
@Sextiva
7 жыл бұрын
Is there a reason that a y-pipe couldn't be used to end up with just two risers? I'd like to run my snorkel along the bottom of the window line and then up along each side of the cage as to not obstruct my view.
@JQuality23
2 жыл бұрын
Super clean, great job….
@jamesroberts3074
9 жыл бұрын
Very well presented and detailed video! TY!
@eacardoc1
9 жыл бұрын
+James Roberts Thanks! I hope it helps!
@cheeseymccheese7249
9 жыл бұрын
Wicked vid man, thanks. I went out and bought all the parts and pieces today...Dunno how much you spent on the install but dam just 1 rubber coupler up here in BC cost me over 10 bucks
@eacardoc1
9 жыл бұрын
Cheesey McCheese Thanks! And yeah the rubber couplers were the most expensive part of the build, I paid around 7 bucks each for them
@RPM_Productions
3 жыл бұрын
@@eacardoc1 why did u vent the water pump?
@billbenson941
8 жыл бұрын
Good job on your video. You explained everything very well. Thank you.
@adambratton9934
10 ай бұрын
Do you have a parts list of what all elbows, etc. Will be needed
@djnemesis82pluss1877
8 жыл бұрын
Shoulda put a hose on that clutch drain and just ran to the side would be real easy to get to the just a thought
@eacardoc1
8 жыл бұрын
Great idea!
@noahyounker689
3 жыл бұрын
Great video!
@stevebillow395
5 жыл бұрын
Looks good thanks
@mossman381
8 жыл бұрын
Thanks for the video. Gave me some good ideas.
@aidannina494
7 жыл бұрын
Hey moss
@mikegasser1975
8 жыл бұрын
Great video save me a lot of time. Turned out the same cheers
@jasonfancey472
5 жыл бұрын
Nice job!
@edbroad472
3 жыл бұрын
The dust Swirl bad behind your back window why would you put the intakes there
@skylarjordan4803
3 жыл бұрын
so do you not need to seal the air box with silicone or anything?
@lachyelmulatiko7435
3 жыл бұрын
Is there any place online to get the clear vent lines and also the rubber grommet
@shippymcship364
7 жыл бұрын
So is there already a hole on the water pump and you just drilled it out bigger?
@zacksworkshop171
8 жыл бұрын
thank you great video
@eacardoc1
8 жыл бұрын
+zackery mccormack Thanks, I hope it helps
@zacksworkshop171
8 жыл бұрын
+eacardoc1 mine is a 2009 only one tube was the same but your video helped a lot
@NorthstarRiders
9 жыл бұрын
Very detailed video. Thanks.
@eacardoc1
9 жыл бұрын
***** No problem, hopefully it helps someone...
@garrett1921
5 жыл бұрын
at 5:10 you talk about that breather hose. i just cut it and ran to separate breather hoses realizing the one from the air box does nothing. The other one seams like its an exhaust hose pushing a lot of air out of the hose i ran. is that ok?
@carefulcasey543
5 жыл бұрын
I don’t understand why he messed with that hose at all. It’s designed to use the air box vacuum to draw the crank case pressure out. If the air box is snorkeled, then that circuit is as well. I don’t think it hurt anything but I don’t see where it gained anything either
@jony070889
7 жыл бұрын
quick question, what did you use to seal on the franco from the belt cover to the snorkel?
@jeremyjohnson388
4 жыл бұрын
Do you build them and sell or have a part list so I can get everything
@jeffstauffer186
6 жыл бұрын
Great Video
@ludicrous8794
7 жыл бұрын
Buen vídeo. Gracias
@tonylopez9649
7 жыл бұрын
great video
@yanzorz71
4 жыл бұрын
Whats the lenght of your riser
@Waathiqful
8 жыл бұрын
Best video I have seen thus far, love the, don't need that, then toss :-).
@eacardoc1
8 жыл бұрын
+Hal Freeman Thanks man!
@goflylow
7 жыл бұрын
DOES NOT WORK OUT ON THE 2008 RZR 800. Nice video but does not work on the 08. Same idea but you will need different fittings and lengths of pipe. Trust when I say this as I made about 5 trips to HD and Lowes. One more trip for a second 22.5 fitting and I should be done. I will try and have a video up at some point with parts list for the 2008 RZR 800 (This is a 50 inch RZR).
@lenh1809
7 жыл бұрын
do you have a parts list for yours
@Waathiqful
8 жыл бұрын
@eacardoc1, I have another questions for you man, what is the product you use to seal between the engine and the belt case? The one in the tube? Is that the same silicon grease you used on the outer seal?
@eacardoc1
8 жыл бұрын
I used "the right stuff" which is made by permatex. It is a very good silicon gasket sealant. Almost too good though, after making this video I found an oil leak and had to pull the engine to repair it. it was very hard to get the back belt cover off the engine without breaking it because it was sealed so well. I used a silicone grease for the outer cover so it would be easily removable when you need to get to the belt.
@jonathanrobledo5186
9 жыл бұрын
Do u have an idea if it's similar for a kawasaki mule 610??? Thanks nice video
@eacardoc1
9 жыл бұрын
I really don't know, I'm not familiar with the kawasaki side by sides. Sorry.
@jonathanrobledo5186
9 жыл бұрын
No problem just a project am working with thanks...
@jjn411
8 жыл бұрын
Since the snorkel install have u notice the belt getting hotter than normal?
@eacardoc1
8 жыл бұрын
No, I haven't had any problems with mine. I don't know if it's true or not but a lot of people believe adding snorkels keeps your belt cooler because when you raise the snorkel air intake aren't sucking in the hot air from the engine anymore.... makes sense to me because you know how hot the area behind your seats get in the summer...
@tylerschoonover7433
5 жыл бұрын
@@eacardoc1 can u email me a list of parts tylerschoonover17818@gmail.com
@Haysan07
9 жыл бұрын
What length riser pipes did you run from the bed too the PVC tips?
@eacardoc1
9 жыл бұрын
15 inches
@Haysan07
9 жыл бұрын
Car doc - when you reinstalled the clutch cover back plate did you torque all six fasteners to 12 ft lb? 3 on drive and 3 on driven clutch
@eacardoc1
9 жыл бұрын
To be honest I didn't torque them, I just went by feel. My service manual does say 12 foot pounds but thats way too much for the little screws on the primary (engine) side. 12 foot pounds would snap them right off.....
@84regalhookshard64
9 жыл бұрын
awsome video man thanks!, how much did all of the materials cost ballpark?
@eacardoc1
9 жыл бұрын
84regal hookshard Thanks! I didn't really keep track but Id guess around $150 maybe less....
@Waathiqful
8 жыл бұрын
+84regal hookshard - I live in the south, so things are a little cheaper, I keep a running total for me it was about $115.00, including tax, minus the price of the sealant that was used between the engine and the belt casing. AIR INTAKE 1- AMERICAN VALVE 2-in X 2-in Dia Flexible PVC Coupling Fitting - $4.46 X 4 2- 3 1/4 inch pipe I pulled from the Charlotte Pipe 2-in 5-ft (80 inch) which was $13.28 3- NIBCO 2-in Dia 22 1/2 Degree ABS Elbow Fitting $2.46 4- 5-in pipe I pulled from the Charlotte Pipe (71-in) BELT INTAKE 1- NIBCO 2-in Dia ABS Couling Fitting - 8.91 cut in 1/2 2- 1 1/2-in pipe - Charlotte Pipe 2-in I got from the 5-ft (69-in) pipe from above. 3- NIBCO 2-in Dia 90 Degree ABS Elbow Fitting $1.99 4- NIBCO 2-in Degree aBS Street Elbow Fitting $2.85 5- 2-in pipe - Charlotte Pipe 2-in I got from the 5-ft pipe above (67-in) left 6- 1-NIBCO 2-in Dia 45-Degree ABS Elbow Fitting $2.99 BELT EXHAUST 1- NIBCO 2-in Dia 90 Degree ABS Street Elbow Fitting $2.85 2- 3 3/4 inch Pipe 1 Charlotte Pipe 2-in from the (63-in pipe above) 3- NIBCO 2-in Dia 45 Degree ABS Elbow Fitting $2.99 4- 8 2/4 inch Pipe - Charlotte Pipe 2-in from the (54-in pipe above) TIP PIPS 1-Charlotte Pipe 2-in Dia 45 Degree PVC Elbow Fitting $0.98 X 3 = 2.94 2- Charlotte Pipe 2-in Dia 90 Degree PVC Elbow Fitting $2.50 X 3 = 7.50 3- 1 Charlotte Pipe 2-in X 5-ft PVC DWV Pipe $5.93 3 CEMENTS (I only needed 2) since I had the PVC glue already 1- Oately 8-fl oz ABS Cement $4.98 2- Oately 4-fl oz Transition Cement $4.97 3- Silicone Grease $3.33 4- 20-ft PVC Tubing 1/4-in $2.99
@chriscrowder8505
8 жыл бұрын
What do you use to seal the snorkels up? I need some.
@eacardoc1
8 жыл бұрын
Do you mean to cap them off when you're washing it?
@chriscrowder8505
8 жыл бұрын
+eacardoc1 no. As in when you build them. You don't just throw pvc pipe together and let it sit do you?
@eacardoc1
8 жыл бұрын
+Chris Crowder Oh, I guess I just assumed you watched the video where i explained all of that....I used 3 different types of cement for the white pvc to white pvc, the black abs to black abs, and the white pvc to black abs.... I explained which cement for which in the video
@chriscrowder8505
8 жыл бұрын
+eacardoc1 wow I'm stupid lol. Didn't even pay attention to it. Thanks for the video man! It looks so clean.
Пікірлер: 75