You don't need to remove the bumper, remove a few bolts from the front of a splash guard and you can access the fog light area from there. That what I did. My fog light kit came with no instructions. Great video. Thanks.
@MountainLust
5 жыл бұрын
Which kit did you buy I'm thinking about doing this to mine soon
@arminmemovic8104
3 жыл бұрын
It's way easier to just remove it.
@edcuenca4843
3 жыл бұрын
Hi can someone please share the exact type of fog light they order and if it fits the 2018 rav 4 le. Thanks in advance
@NarineSingh0598
Жыл бұрын
Got a video of how you did it ?
@brianmarzan6392
3 жыл бұрын
Successfully tackled this job today thanks to your video. There are two keys to using the existing harness to install the aftermarket kit. Install the missing relay in the relay box, and use the aftermarket switch to ground pin 56 when you want the fog lights to operate with the low beams. Brilliant!
@sakitlikod1
5 жыл бұрын
I salute you doing this by yourself. Good job mr.G
@ChrisG-ph7yf
6 жыл бұрын
After having my lights for a long time, I finally installed them today. I'm kinda disappointed in myself because I waited so long to install them since I thought it was going to be difficult. They were actually fairly easy. (I should note that I own a car stereo shop, so this is what I do) You don't have to take the nosecone off. It's tight, but you can just remove four 10mm bolts/screws from the underside of each side, and move the wheel liner enough to get them in place. Then it's a pushpin and two 10mm bolts/screws that hold the blanks in, and you'll reuse those bolts/screws to install the new lights. The top bolt is tough, use a deep well socket or a shorty extension. While installing, you'll see the factory fog light wiring harness, you're going to want to plug that in after you're done installing the lights. (The plugs are green) Realign the wheel liner, and reinstall the four 10mm bolts the same way you took them out. Then, you'll follow the video for the switch installation, and make the same attachments that the video showed. (THANKS Cz Gu!) I had a positive switch, and I used a relay to reverse the polarity. (Relay: pin 85 goes to green wire of switch, pins 86 & 87 go to ground, pin 30 goes to what the video refers to as pin 56 in the car, it's the bottom right most wire in the plug on the video) Then I ordered an AR614 relay from NAPA, pushed it into the spot (under the hood in the relay box) as directed in the video, and everything worked. NOTE: I put an inline 10 amp fuse on the red switch wires that tap into the red wires on the traction control button, just for my own peace of mind. If anyone has any questions on how I did it, ask away.
@justinohsbeats
5 жыл бұрын
i have a postive switch going to try your setup thanks alot where to i go to get the other switch is that the factor one?
@Toyotaguy999
4 жыл бұрын
What color is the other wire? First is green i know
@Toyotaguy999
4 жыл бұрын
How do i get green wire into pin 56?
@edcuenca4843
3 жыл бұрын
Anyone have any idea if it will be the same installation for 2018 rav 4 le? Thank you
@philindeblance
8 жыл бұрын
I think the next upgrade you will do is sound proofing the doors so they block exterior noise, and don't sound like a tin can when you close them! Great video!!!! Thanks for the follow up with diagram!
@El_chero
2 жыл бұрын
Wowww! You are amazing. I did all re-run the wiring because I had no idea about how to connected with the “already wired lines”. What a boomer! How come I did not see it your video first!!!
@czgu6398
9 жыл бұрын
The switch has 4 wires: Hot circuit Pin 1 and Pin 2 is regular open, Ground circuit Pin2 and Pin4 is regular open. (Pin1 ~ Pin4 from left to right). You can use meter to check. You'll not make mistake. In engine compartment, there is a fuse box on the right side. Fuse 6 is for fog light. I think the fuse is manufacture installed, just like harness. But you can check to make sure it's there.
@7777LORENZO
4 жыл бұрын
You are Great ! Doing that job by yourself ! Just so wise and brave 😄
@RikuRicardo
8 жыл бұрын
Thank you so much for the video! I had the same exact reaction when you were removing the bumper cover and it fell down. I hope it didn't get chipped.
@czgu6398
8 жыл бұрын
+RikuRicardo I did two projects at same time -- fog lights and parking sensors. I installed 2 front sensors. So that why I had to remove the front bump cover and Oooops
@terriquez87
3 жыл бұрын
I installed fog lights on my 2015 Toyota RAV4 LE I used the the factory connections for the lights and it’s not working my switch that I installed lights up when I push it in but the fog lights don’t turn on I need help! Thank you in advance
@beotheguitarist
6 жыл бұрын
Thank you for this video. I will attempt this as soon as I get my fog lights. I have the same 2015 Rav4 LE so it should he the same. This video was perfect! My only concern is that hot circuit and ground circuit switch. I have a multimeter so I'm sure I'll get it right.
@juanmarcosmarquez2902
7 жыл бұрын
thank you for all the vids you are making, i tried to install a foglight on my LE, using the stock circuit line,but i guess the switch that was included was the problem,so i just did the ground install..
@vincemilton2003
4 жыл бұрын
The connection stages !!!! you connected the two red wires and t-tape to the other red wires and than you the green line you pin it to T56 and what do u do with the black wires ?????
@czgu6398
9 жыл бұрын
If you check the most left 2 wires, they should be regular open for hot circuit switch. If they are not, then check right side 2 wires. If the 2 pair wires are all not open, then this could be a ground circuit switch. Check 1 and 3, 2 and 4, make sure it's a ground circuit switch. .....
@JohnSmith-gj8fd
3 ай бұрын
I have to give it to you sir, you made an LE into a Prime.
@joselollopez59
3 жыл бұрын
Thanks for recording and share this wonderful video.
@tomvu1073
9 жыл бұрын
Cz Gu, thanks again for helping me out. Just wanted to let you know my fog lights work. Only issue is I can't turn on/off the fog lights whenever I want too. My fog lights will have to be turned on every time when I turn on the headlights. This must be a switch problem. But I don't care, Lights turn on and it works.
@czgu6398
9 жыл бұрын
Tom Vu Congratulations!! Yes that is the way RAV4 fog light works: It can only turn on when high beam light is ON. Your switch is fine! We use RAV4 existing harness so it works the way RAV4 does.
@czgu6398
9 жыл бұрын
J Diaz I don't know why you want connect it to parking lights. Parking lights will not turn on when you drive. So fog lights will be useless. If you connect the 2 red wires to Acc 12V, then you can turn on fog lights after you turn the key. Pin 45 of 3C is acc 12V. It's red wire. Or you can connect to constant 12V. Turn ON and OFF fog lights any time you want.
@fernandoavila1453
8 ай бұрын
Hey I'm following the steeps you took I'm at the point where I have to do the wiring and where does the green wire go? Exactly
@titorivera6762
8 жыл бұрын
thanks...i installed fog light kit on my 2015 rav4 by your instructions and they work smoothly. at first without turning engine on the switch lid but fog lights were off. as soon i turned engine on wala!!!! they actually turn on....strange.....
@miked5106
Жыл бұрын
did u remove bumper cover or go in thru the wheel well
@tjordan7067
7 ай бұрын
Thanks my brother i can use this video..
@petet7107
Жыл бұрын
well, I tried your method for both the ground circuit switch, and then when that did not work I attempted your method for a hot circuit switch by switching the wires around. Neither are turning on the fog lights. I have the black grounded on the ground screw, the red Ttapped to the red wire, and in my case, the yellow wire Ttapped to 56. All I’m getting is a light on the actually switch. Nothing changes when I press it and I’m getting no power to my fog lights.. any thoughts? I inspected both the fuse under the steering wheel, as well as the fuse in the fuse box, both 7.5 fuses seem to be good. I also tried swapping the relay in the engine with another, but that didn’t work either.
@petet7107
Жыл бұрын
@czgu6398 would really appreciate your help. This was supposed to be a very quick install. Everything took me 30 min but its not working. I tried both ways and even ordered another switch to see if it was that. Still no light.
@pandukab
8 жыл бұрын
Is 2012 Rav4 relay connected the same way or does it need to go underneath the dashboard, just left bottom of the steering wheel?
@temporaire79
9 жыл бұрын
I don't know if it's the same think in north america because if i connect in the hot circuit with one denzo relay, i can't open my fog light. I put the two red wire in the traffic switch and i have a power in my fog light switch and i put the yellow wire with possibly pin 56 in right down corner but the fog light not open. I don't know if you understand my question because i'm french sorry.
@ciprianmihai1268
8 жыл бұрын
A very useful video, I was wondering, Would it work in same way for a Toyota Sienna LE 2013, model? Thank and Indeed very useful!
@vpattt1619
Жыл бұрын
I would love to do this conversation on my awesome 2015 LE RAV4 but I am quite dumb and this seems a little too much for me. But I did manage to swap out the front turn signals, headlights and DRL/high beams from halogen to LEDs.
@ETPhHm57
8 жыл бұрын
CzGu, Could you help me to get my fog lights working slightly different than the way you did it on your 2015 RAV4? I have a 2014 RAV4 LE that has the harness and fog light fuse already in place but no fog lights and no relay (same as your 2015 model). I too ordered the kit that came with the "hot switch". I liked very much what you did with all your efforts to help the rest of us out, but it is still unclear to me how to modify the "hot" switch to turn it into a "ground" switch. It seems like you have used diodes in your hand written diagram in part 2 of your video. If I try to accomplish the same method as you did, will this make it where the fog lights will come "on" only when the high beams of the headlights are turned "on"? I would rather turn the fog lights on/off manually, but override the fog lights to "off" when ignition key is turned off (position 1). I believe you stated this could be done with 3C pin 45 (+ACC). However, it seems that Jester Gallardo did this and encountered a whole bunch of warning light problems on his dash panel that he listed in his post. I believe you replied that was probably because he was connecting ACC+ to ground. 1) So my question is, should I use the "hot switch" version that has a control wire (WHT , YEL, or GRN as the case may be) and also use 3C pin 45 so that the hot switch only receives power when the ignition key switch is turned to position 2 or 3? I am still thinking that the factory installed fuse will still come into play if I am using the factory installed harness. I am also thinking that I will still need to buy the Fog relay and place it in the relay box on the left side under the hood. Are these two assumptions correct? 2) I still haven't figured out where my control wire (WHT , YEL, or GRN as the case may be) connects to and where to connect the red wire of the "hot switch". You said in your videos to connect the red wire of the fog switch to the red wire of the TRAC/VSC switch located on the left side of the fog light switch in your video. However, that is also assuming you are using the modified "ground switch". Again I have a problem understanding your modification. You say that you cut two wires and added two wires, but your diagram also shows diodes being used. I also don't like it configured where the fog lights will come "on" only if the headlight high beams are "on". I think its a better idea to be able to switch the fog lights "on" and "off" any time, but only when the ignition ACC+ switch is in position 2 or 3. Can I do this with the "hot" switch, unmodified? I apologize for this long-winded post but I think cryptic explanations are the main reason why there is so much confusion here. Words and detailed explainations avoid all that. Thank you again for all your efforts in trying to accommodate everyone.
@biologo5941
8 жыл бұрын
My 2016 RAV4 are pre wiring on front like 2015, but inside are different because don't have a transit switch beside the fog light switch space. It has a DASH INTERIOR DIMMER LIGHT SWITCH ADJUST CONTROL. Were I can find a good power red cable to connect my fog light switch? Regards, José
@constantin3364
2 жыл бұрын
I have 2022 Toyota RAV4 can I set up the fog lights The same like you did with the 2015 model
@richardhyde9180
2 жыл бұрын
Have not found a Ground switch is there away to setup a hot set to be a ground switch
@mdlcasi2000
4 жыл бұрын
removing the front bumper/grill looked easier to do than working from behind the splash guard.. I wonder if all rav 4 models have existing wiring for the fog lights (I have a 2019 2wd rav4 base model) great video.. thx
@jesuislajesuisla8802
2 жыл бұрын
Is there a way I can turn on the foglight without using the main switch, just the foglight button?
@4ujkdguy
8 жыл бұрын
Most Ebay switches are positive sided switch but you need one relay to make the fog lights work but they will not turn off when the high beams are on!
@perf8032
5 жыл бұрын
Why do you need the fog lights to turn off during high beam? I hardly ever use the high beam in California
@saelee33
4 жыл бұрын
Can I use the switch that came with the box and cut the wire from the wire and use that? Will it be the same or do I have to order the switch separate?
@manuelaldairvargasmachuca1189
5 жыл бұрын
Hi I have. 2013 Toyota rav4 LE made in Japan I noticed there is a difference, mine does not come with the wires under the panel so I wonder how can I pass thru the cables from engine to inside car it's hard
@michaelschratz4842
2 жыл бұрын
Will the fog lamps auto turn off when highbeams turned on?
@saelee33
4 жыл бұрын
Does the kit comes with ground circuit switch? Do I need to order it separate? Can you put it down on your description what kind of switch I need to order?
@docwindsurf
7 жыл бұрын
Any idea how this would work for a 2017 RAV4? Instead of your Traction Control switch, mine has a Lane Departure button. Can I still tap into that button's red wire? Still look for 3B pin 56? Thanks so much!
@chapizoo
6 жыл бұрын
Im in the same spot....no idea how to use original wiring on my 2016 rav4....did you find out?
@Mcivstx
5 жыл бұрын
Did you ever manage to get it installed?
@scyllis
5 жыл бұрын
We recently bought 18 RAV4 LE and I am planning to tap two cable to Lane Departure button and 3c with pin 36.. Any insight? .
@marcorodriguez6603
2 жыл бұрын
What did u do with the black line from the plug?
@lmomechtech7709
8 жыл бұрын
Another kool vid! Thanks!
@tomvu1073
9 жыл бұрын
did you disconnect the battery when doing the wiring in the cabinet? where does the black ground wire connect to when doing ground circuit switch?
@czgu6398
9 жыл бұрын
Tom Vu I didn't disconnect the battery. You can connect to any place on metal frame. these is a ground point in the front, low of driver side, it's very inside. Using flash light, you can find it. The most important thing is that you need to know what kind of dash switch you have.
@czgu6398
9 жыл бұрын
The only wiring is to wire the fog switch (if you use ground circuit switch). At the end of this video, you can see the diagram of ground circuit switch. There are 2 red wires. Connect these red wires to red wire of traffic switch (just next to the fog switch). Black wire of the fog switch connect to ground. The green wire (or yellow wire. color may different. it's from pin 2 of the fog switch) is connected to 3B pin 56. 3B is a 56 pin connector which is the longest one on the left side. Pin 56 is the last pin on the right corner of 3B plug. If you have a hot circuit switch, you need another relay.
@tomvu1073
9 жыл бұрын
Cz Gu
@lic4953
9 жыл бұрын
Cz Gu My fog lights came today, and it is the same switch like yours “Hot Circuit Switch” after meter testing. I rarely like to use factory existing harness, as you suggested, but need help to see how to connect the second relay. I watched your video few time, it seems you only installed one blue relay, no second relay on the video show. Can I do the same thing like you did, for Hot Circuit Switch? Will that works? Or, if you are able to offer more picture information for how to install second relay. Since currently eBay only sales Hot Circuit Switch, and you’re the only website offered this video show for using factory harness, that is the best idea! Thank you for your help.
@czgu6398
9 жыл бұрын
LI CHAO Please watch my another video ".... installation 2"
@dustinstelter6020
5 жыл бұрын
Where do you hook up your ground wire? Just on any pice of metal or do you t tap into another wire?
@winsertvedrine1632
5 жыл бұрын
Hi guys do need help to connect my fog light switch. I don't what I didn't wrong , I did use the OEM wires . I got my two red wire connect to red traffic switch , black to ground , and yellow to last pin on my right hand the white wire . Switch turn on but the light stay off . Help please
@alejandrocalderon1784
6 жыл бұрын
I've trying to look for the kit name, model or any info to buy it. can anyone assist me with this info. Thank you
@JoseAGomez-fw4vg
Жыл бұрын
Where does the black wire go? I’m doing everything exactly but lights are not working??
@kingvonfluffy5574
3 жыл бұрын
Does anybody know if you’re able to change out a bumper from a 2014 rav4 to a 2016 rav4 bumper?
@allanmanmano6854
3 жыл бұрын
Hello can any body tell me how to connect the foglight switch.ive used the existing wire harness on my 2018rav4.i put on the relay and the light but i dont know how to install the switch
@luisvarela6694
3 жыл бұрын
Thanks for the information. This also applies to rav4 2017, please help with the connection to turn on the fog light
@user-gi3xj8nz3s
7 жыл бұрын
Will this be the same steps on a Toyota Corolla LE ?
@carlosauza1038
7 жыл бұрын
Mr. Cz Gu, i followed your instructions and everything worked fine. Now I upgraded my car to a 2017 RAV4 LE and i want to add the fog lights as well. have you tried to do it on a 2017 RAV 4 LE? if so, i would be forever grateful if you share your knowledge.
@czgu6398
7 жыл бұрын
2015 Toyota RAV4 LE is so disappointed. I'll sale it soon and buy other SUV instead.
@arkansasguy97
7 жыл бұрын
what was the red wire that was just hanging there ran thru the firewall where does that connect?
@sung5087
7 жыл бұрын
I just bought 2015 rav4 LE AWD. why is this car not good? I paid 15,000 dollars. please tell me what is not good?
@fredchilson6451
7 жыл бұрын
Hello, I followed the directions and cannot get the fog lights to work. My switch shows power, but will not trigger the lights. Any information would be great!
@ChrisG-ph7yf
6 жыл бұрын
Did you add the under hood relay?
@tomvu1073
9 жыл бұрын
j diaz did you get yours lights to work?
@djclown7pb
6 жыл бұрын
Is this a kit? I want to add fog lights to my 2013 rav4
@aguyster
Жыл бұрын
What kind of relay did you put in?
@perf8032
5 жыл бұрын
I want to perform the steps for installing fog lights on my 2015, anyone has an idea where I can get the ground circuit switch? So I can use the factory harness instead and install the simple easy switch.
@user-ip6li1xx6j
7 жыл бұрын
how should I connect a black wire to ground? Please tell me.
@scyllis
5 жыл бұрын
I guess you attaching side wall of the car with removing kick panel.
@damiensamad2066
7 жыл бұрын
Good day sir. Where did you get your switch? I can't find the same one. Is there a part number?
@czgu6398
7 жыл бұрын
I bought fog light kits at eBay. There is no part number.
@damiensamad2066
7 жыл бұрын
thank you
@frankt1032
8 жыл бұрын
RE: 2015 Toy Rav4 fog light installation (for hot circuit switch) To: CZ Gu - on your installation 2 you mentioned that the green (pin #2) wire is connected to 3B pin 56. The diagram clearly showed pin #36 ( last pin on the bottom right corner of the 3B plug) . Pin 56 is located on the top right corner of 3B plug. Please make a correction which one is right ? . Thanks
@czgu6398
8 жыл бұрын
+Frank T The bottom right corner of 3B is Pin 56. Pin 36 is on the top right corner. You need to connect to the bottom right corner -- Pin 56.
@jordannguyen9998
4 жыл бұрын
Can you record more videos at connecting the ends of fog light switch rav4 2015 more Thanks
@alonsolopez8736
3 жыл бұрын
Me too
@joekamer7779
Жыл бұрын
where do you get a ground switch
@johnkosheluk1041
3 жыл бұрын
Ues but we're do you get that wireing diagram
@kenny19142
6 жыл бұрын
If I don’t use the switch and just connect the fog light directly to the factory harness, will it still turn on?
@ChrisG-ph7yf
6 жыл бұрын
No
@Tejas04932
6 жыл бұрын
Can you share me wiring diagram for RAV ,2013 model , I want to install after market cruise control switch
@mytube30005
6 жыл бұрын
Will the fog lights automatically turn off like the headlights or you have to manually turns off?
@ChrisG-ph7yf
6 жыл бұрын
Depending on how they're hooked up, but will most likely turn off with headlights.
@cesarmeza8490
6 жыл бұрын
Looks easy at the beginning but 👋🏽 hey you don’t to mess with the cables
@justinohsbeats
5 жыл бұрын
hey so. i was wondering, where is the stocl connector? there is connectors for the fog lights, a location for a fuse and relay. what i dont understand is why isnt there a connector sitting there waiting for a switch to be installed? why would they have everything else ready and not have a connector? i just installed the fog lights. the fog lights plugged into the stock harness behind the bumper. installed the relay. and i installed the switch after splicing. but what i dont get is why do i have to splice if everything else is there? theres gotta be a plug and play setup for the factory.
@handymanaloto642
8 жыл бұрын
I installed already my foglight it is also a rav4. 2015.my switch is turning on but my fog lights are not working... What should i do? Thanks
@titorivera6762
8 жыл бұрын
+Handy Manaloto friend try turning vehicle on and give it a try...see if it works!!!!good luck.
@karlyanny
8 жыл бұрын
hy,can you tell where did you get that foglight switch so I can get it too....
@catrashoo
3 жыл бұрын
I think he said he bought everything on Ebay.
@kaikeeduardos2468
3 жыл бұрын
Sir tha installed was fast but the connection for the cables it's not clearly to see what do you do
@sherilynverdey536
6 жыл бұрын
Hi there, is it posible to connect it to low beam rather than in high beam?
@ChrisG-ph7yf
6 жыл бұрын
I connected my two red switch wires to a positive parking light wire, so that my fogs will work any time the parking lights are on. If you want the fogs to turn off with high beams, you'll need to connect the two red switch wires to a positive low beam headlight wire. That way, they'll turn on with low beams, and turn off with high beams.
@sakitlikod1
5 жыл бұрын
Mr.G ,can you tell me where’s your 2015 rav4 LE manufactured from,is it from Canada ?
@czgu6398
5 жыл бұрын
I don't know. I don't have this vehicle anymore.
@sakitlikod1
5 жыл бұрын
Ok, but it was LE base model and has hubcaps right?
@tomvu1073
9 жыл бұрын
I have the connector from the fog light harnest that i wont be using. I was planning to cut it and t tap it. Its the same colored wires like in your video , 1 black, 2 red, and 1 yellow one. Will that be okay for ground circuit? Or will i need to buy a new switch? With the same wires like the one you are using? This is the only step i need to do is connecting the wires.. Thanks for responding:)
@czgu6398
9 жыл бұрын
Tom Vu Sure you can use the connector. Also you need to make sure it's ground circuit switch. If it's a hot circuit, then you need the relay comes with fog light package.
@czgu6398
9 жыл бұрын
J Diaz If you check the left 2 wires, they should be regular open for hot circuit switch. If they are not, then check right side 2 wires. If the 2 pair wires are all not open, then this could be a ground circuit switch. Check 1 and 3, 2 and 4, make sure it's a ground circuit switch.
@czgu6398
9 жыл бұрын
J Diaz Actually ground and hot switch has only one wire connect differently. Two red wires always connect to red wire of traffic switch and black wire to ground. You connect yellow wire to pin 56 of 3B, and push the button, if head light is ON and fog light is not, then you have a hot circuit switch. You need add a relay. You can use the relay came with the fog light kit.
@tomvu1073
9 жыл бұрын
J Diaz That's what I have too.. I had to cut the wires from the harnest and just separated the them from the rest just leaving the 2 red wires (connects to the red wire like in his video), yellow (connections to 3b, 56) and black wire (Ground wire, connect it at the very bottom left near the hood opener)
@tomvu1073
9 жыл бұрын
J Diaz Make sure to install Toyota relay 80090-87026 relay in the car before turning on the fog lights
@mhaco0227
9 жыл бұрын
hi... I tried this video on my 2013 rav4... put the other wire in 3C pin 45 instead on 3B pin 56.. but this problem came out.. can you help me with this... thanks when I start the car using key in ignition switch, some dashboard lights still on like steering wheel lock light, abs light, airbag light, traction light... power window, aircon, radio, 12v outlet not working... steering wheel and gear is locked.... but when I start it using remote starter, it works well, all the problems gone... when I started it using remote starter, then put the key on ignition switch to drive the car, all the problems that I said back on, except that the shift gear is working... steering wheel locked light back on, but it is working... thanks...
@czgu6398
9 жыл бұрын
Jester Gallardo 3C pin 45 is acc +. 3B pin 56 connects to ground when the relay triggered. So if you connect this wire to acc +, when you push fog light switch, 3C pin 45, which isacc +, will be connected to ground.
@ETPhHm57
8 жыл бұрын
@Jester Gallardo Did you ever get your fog lights working the way you wanted? I have a 2014 RAV4 LE that has the harness and fog light fuse already in place but no fog lights and no relay (same as CzGu's 2015 model). I too ordered the kit that came with the "hot switch". I liked very much what CzGu did with all his efforts but very unclear on how to modify the "hot" switch to turn it into a "ground" switch. Seems like he is using diodes and such according to his hand written diagram in part 2 of his video. Having fog lights "on" at the same time as the high beams of the headlights is very undesirable. Anyone that has driven in fog knows that high beams make visibility even worse! So, I would rather turn the fog lights on/off manually, but override the fog lights to "off" when ignition key is turned off (position 1). I believe CzGu stated this could be done with 3C pin 45 (+ACC). However, it seems that when you did this, you encountered a whole bunch of warning light problems on your dash panel that you listed above in your post. CzGu replied that was probably because he was connecting ACC+ to ground. 1) So my question is, should I use the "hot switch" version that has a control wire (WHT , YEL, or GRN as the case may be) and also use 3C pin 45 so that the hot switch only receives power when the ignition key switch is turned to position 2 or 3? I am still thinking that the factory installed fuse will still come into play if you are using the factory installed harness, and I am also thinking that I will still need to buy the Fog relay and place it in the relay box on the left side under the hood. Are my assumptions correct? 2) I still haven't figured out where my control wire (WHT , YEL, or GRN as the case may be) connects to and where to connect the red wire of the "hot switch". CzGu says to connect the red wire of the fog switch to the red wire of the TRAC/VSC switch located on the left side of the fog light switch placement in his video. However, that is also assuming you are using the modified "ground switch" version like he used. Again I have a problem with the modifications CzGu made. He says he cut two wires and he added two wires but his diagram shows diodes being used. Very unclear. It is my understanding that CzGu's method makes it where the fog lights only come on if the headlight high beams are "on". I think its a better idea to be able to switch the fog lights "on" and "off" anytime, but only in conjunction with the ignition ACC+ switch (position 2 or 3), so that you don't accidentally leave the fog lights on and run your battery down. I need help achieving this. I apologize for this long-winded post but I think cryptic explanations are the main reason why there is so much confusion here. Words and detailed explainations avoid all that. Thanks again to CzGu for all his efforts in trying to accommodate everyone.
@mhaco0227
8 жыл бұрын
+ETPhHm57 yes, I got my fog lights working, but don't connect it to 3C pin 45 because there is a chance to mess up your car, your 5 amp fuse under the dash might blow... just connect it to 3B pin 56, it is just almost the same. if you are on high beam, just press the switch for fog light off... And I made a thread on how to use the hot switch, instead of converting hot switch to ground switch.... Just visit this.. www.rav4world.com/forums/124-4-4-interior/198386-solved-2013-fog-light-wiring-switch.html Hope you will understand my explanation on that thread... And just reply to this comment if you found something that you didn't understand... Thanks...
@ETPhHm57
8 жыл бұрын
@Jester Gallardo On the other website Rav4World, I noticed that you have exactly or almost exactly the same fog light kit that I have. My 2014 Rav4 also has the existing wiring harness in place, and it also had a 7.5 amp fuse in the fuse box under the hood on the right-hand side, but no relay in the relay box under the hood on the left side. My concerns are, you seem to be using two relays on your setup (one in the relay box under the hood, plus the one that comes with the kit on the harness). Do these two relays seem to play nice together? Also, the existing fuse in the fuse box under the hood is 7.5A, but my wiring harness kit has a 30A fuse in-line (I believe yours does too). The huge difference in fuse rating seems a little sketchy to me and here is why: No one seems to have mentioned or taken this into consideration in other posts and threads, but there are two types of fog light bulbs that are typically being shipped with the kits from eBay and Amazon: There is the H11 bulbs which is what I have (and I think you have as well) and I believe these are 55 watts; and then there are kits that come with H16 bulbs which I believe are rated at 18 watts and I believe those bulbs are what a Toyota dealership typically installs with genuine Toyota fog light parts. There is quite a bit of difference in the wattage on these two bulbs, and hence, I believe that is why there is only a 7.5 amp fuse in the fuse box under the hood because the Toyota OEM bulbs are 18 watts X 2, or 36 watts total. In contrast, the H11 bulbs I believe are 55 watts X 2, or 110 watts total, which is too much for a 7.5 amp fuse at 12 volts. I am not sure if you have the H11 bulbs in your kit, and you did not mention if you used the in-line 30A fuse that came with your kit, but did you replace the 7.5 amp fuse under the hood with something bigger? I would think you need at least a 15-20 amp fuse, but the kit comes with a 30 amp fuse which is pretty big. There is also another potential issue with the higher wattage bulbs: the wire gauge of the stock wiring harness verses the wire gauge of the harness that comes with the kit. If there is a substantial difference between the two, this could be a problem but only if the existing harness uses smaller gauge wire for the power wire. Some of the wires on my kit harness from eBay are a little heavier gauge. You might recall that CzGu makes mention of this in some of his videos or posts and says to gauge it down so it will fit in certain connector splices (not a good idea in my opinion if you have the H11 bulbs). I have not been able to verify if the kit harness is the same gauge or larger gauge than the existing wiring harness. Also, I contacted the wiring kit re-seller on eBay (not the manufacturer, but the retailer) and they strongly recommended using the kit harness and not the existing harness. This would basically turn a 30-minute job into an all day job if you have to re-wire the whole job. Could you please elaborate on the following: (1) do you have the higher wattage H11 bulb types, (2) what did you use for the the fuse under the hood (stock 7.5A or did you replace it with a larger fuse), (3) have you compared the wire gauges of the existing harness verses the harness that came with the kit, (4) did you use the additional 30A in-line fuse that came with the kit, (5) how well do the two relays work together if they are both used in your system, and finally, (6) how long have you been successfully using your fog lights and how often do you use them? I wonder if you had them on for long periods of time if the wiring got hot and melted or shorted out. Thank you so much for responding here.
@arviecordero7976
8 жыл бұрын
Hi.. I just want to ask if the fuse that you put in the fuse box is included in the ebay kit? If not were can i buy that and what kind? Thank you sit..
@mariselv.5159
8 жыл бұрын
Where do u buy the ground switch itself or how do u convert from hot circuit to hot circuit switch?
@synedis
6 жыл бұрын
did you ever get an answer? i am after this specific answer as well lo clear the generous but quiet foggy technical details of mister cz gu
@ChrisG-ph7yf
6 жыл бұрын
See my long post above
@tomvu1073
9 жыл бұрын
what is t tap size for the wiring?
@stephenbrown5844
7 күн бұрын
Whats he up to,,, the bumper now needs spraying🙄no need to remove it😮
@synedis
6 жыл бұрын
it should be mentioned that this wiring is ok i think for left hand drive canada made rav4.for japanese made rav4 it is different.
@ozcnueve
3 жыл бұрын
nice!!
@user-yk7fw8fn4n
5 жыл бұрын
what size lamp fog light ?
@georgecavazos2449
6 жыл бұрын
Where did you order the relay from? Please provide part #.
@czgu6398
6 жыл бұрын
I bought it at eBay. Denso 90080-87026 or Toyota 90080-87026.
@georgecavazos2449
6 жыл бұрын
Thank you
@edcuenca4843
3 жыл бұрын
@@czgu6398 is it original toyota part? Thanks
@czgu6398
3 жыл бұрын
@@edcuenca4843 No it's not.
@edcuenca4843
3 жыл бұрын
@@czgu6398 will the installation be same for 2018 rav 4 le? Thank you
@kmills4408
9 жыл бұрын
what is the part number of the blue relay you added?
@czgu6398
9 жыл бұрын
+KMills440 Please check video "Please check "2015 Toyota RAV4 LE Fog Light Installation 2".
@galileoabejo2652
4 жыл бұрын
Just ask where and what site did got the fog light assembly?
@czgu6398
4 жыл бұрын
I bought it on eBay
@galileoabejo2652
4 жыл бұрын
how about the relay,what kind?
@czgu6398
4 жыл бұрын
@@galileoabejo2652 Toyota relay 80090-87026 (about $7 on ebay or Amazon).
@mrg406
6 жыл бұрын
Does anyone know thé model of thé kit and additional parts used
@dansyz80
Жыл бұрын
I did the same on my 2016 rav4
@berenicesanchezsuarez967
3 жыл бұрын
I can't see the pink cable well where the connection is made
@jeepneyride
8 жыл бұрын
Do you have the complete wiring diagram of 2015 Rav4?
@czgu6398
7 жыл бұрын
No I don't have. Check following link: www.rav4world.com/forums/124-4-4-interior/176649-every-wire-its-location-2015-rav4.html
@parastiwari7903
8 жыл бұрын
Hello cz gu! What can I use for 2013 le that can use factory wiring?
@czgu6398
8 жыл бұрын
Yes I think so.
@parastiwari7903
8 жыл бұрын
Great! also could you send me a link to where to buy it. Thankyou!
@czgu6398
8 жыл бұрын
It's been long time. I bought it at eBay. You can search "2013-2015 TOYOTA RAV4 BUMPER CLEAR FOG LIGHTS" at eBay.
@czgu6398
9 жыл бұрын
2015 Toyota RAV4 LE all have existing fog light harness. Your RAV4 has it for sure!! www.ebay.com/itm/291014764749?_trksid=p2060353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT This is the cheapest one I could find. But the dash switch was not good. So I had to buy another dash switch. Price was low but not a good deal!! The switch came with the fog light has only one LED light -- ON or OFF. Dash switch need 2 LED lights. Both LEDs will be OFF, if switch is not pushed in or car does not start. If car is running and switch is ON, but headlight is OFF, one LED will be ON. If headlight is ON, both LED will be ON. Some one said that he bought fog lights and brackets without harness for about $40. But I couldn't find it. You only need a pair of fog lights and brackets, one dash switch (with LEDs) and a Toyota relay 80090-87026 (about $5 on ebay). Maybe following deal is better: (Dash switch has two LEDs) www.ebay.com/itm/2013-2015-RAV4-BUMPER-FOG-LIGHT-SET-LAMPS-OE-STYLE-SWITCH-HARNESS-/271881302717?fits=Make%3AToyota|Model%3ARAV4&hash=item3f4d6372bd&vxp=mtr
@efgarcia7354
7 жыл бұрын
Isn't necessary to remove the bumper cover to do the installation.
@czgu6398
7 жыл бұрын
I did two projects, one was fog light, another was installing front parking sensors.
@chasburns3303
6 жыл бұрын
EF G. Do you know whether installing fog lights for a 2015 Highlander Le would be a similar install Also, do you know where I can find installation instructions '15 Highlander? Is there a harness already there? Thanks
@dickjavier8777
3 жыл бұрын
Does this connection work with 2013 rav4?
@oi32df
Жыл бұрын
for a canadian made Rav4 : yes
@chunkylover382
3 жыл бұрын
What is the part number to order ?
@handymanaloto642
8 жыл бұрын
When i turn on my foglights switch its button lights turn on but foglights are not turning on.
@czgu6398
8 жыл бұрын
+Handy Manaloto There are 2 conditions to turn on fog light. 1. Fog light switch must be ON, 2. Head light must be turned on.
@handymanaloto642
8 жыл бұрын
Yes my fogwitch and headlights are on but foglights are not on.. Is it possible that they give me the wrong relay?
@sibrahim2531
6 жыл бұрын
good job thanks
@synedis
6 жыл бұрын
as 100% of the fog switches sold on ebay are hot circuit one have you any idea how to convert it to ground circuit ?cheers
@ChrisG-ph7yf
6 жыл бұрын
See my long post above
@wackz21
8 жыл бұрын
did you change your foglight bulb?
@wackz21
8 жыл бұрын
thanks for the video
@czgu6398
8 жыл бұрын
+wackz21 Yes. I used LED fog light. I bought 2 sets of LED fog lights. One pair for share. These are very good.
@wackz21
8 жыл бұрын
+Cz Gu do you have a link where you purchased the bulb? how about for headlight any recommendations too?
@czgu6398
8 жыл бұрын
+wackz21 I bought from China. But you can easily find LED fog light for $15-$25 on ebay.
@jbizarroable
2 жыл бұрын
Where does the blk wire go???...is it a ground ??????
@jatinderminhas1424
8 жыл бұрын
His Video has missing almost all electrical wiring and connecting point. The way he is explaining, only he can finish him self. He could not explain all wiring connection. I can see red wire coming out by left door Driver side panel. But he forgot to tell where it had to Attach
@synedis
6 жыл бұрын
i agree this video is very generous from mister cz gu but incomplete and confusing as his words and explanations don't match the pictures.
@rudyestrella8223
6 жыл бұрын
¿Hola!!! Como puedo conseguir las mismas luces , como se llaman las que el le instalo
@cesarmeza8490
6 жыл бұрын
Las fog light ? Oh el color de las Luces si no me equivoco el color parece ser un 5000k
@cesarmeza8490
6 жыл бұрын
Pero todo lo que tu quieras lo puedes conseguir en EBay solo ocupas la información de tu auto y encontrarás bastantes artículos
@zeta6798
5 жыл бұрын
Rudy Estrella Gracias
@shonabraham3808
4 жыл бұрын
Good
@MCCarbons
7 жыл бұрын
buy a led fog lights replace the original halogen fog lights must be cool.
@angelbluerider9588
5 жыл бұрын
dropped the bumber hope it didnt get scratched.
@tomvu1073
9 жыл бұрын
Hi thanks for the video.. Can you show more of the wiring? Or do a short video more on connecting the wires. Thanks.. video is very helpful.
@user-gi3xj8nz3s
7 жыл бұрын
Tom Vu yes that would be helpful and will this be the same steps to follow on a 2016LE Corolla
Пікірлер: 194