😊Very helpful reference for Axle work on the Macan. So much easier to remove the top ball joints than messing with the heat shields to get the axle out. Thanks for recording and posting.
@hansgarage1751
7 ай бұрын
Glad it helped!
@n9nes6x69
Жыл бұрын
Appreciate your diy videos on the Macan as not many videos out there exist. 🏆
@hansgarage1751
Жыл бұрын
Thanks! We'll add more each time we repair.
@alexkaka7197
Жыл бұрын
You explained a lot better than most of the techs on the YT
@hansgarage1751
Жыл бұрын
Thanks!
@builtyankeegirl
Жыл бұрын
Great video, saving money, doing hands on and learning while you do it makes having great cars ...even better.
@hansgarage1751
Жыл бұрын
Very true! Thanks for watching!
@ergenekonreis
4 ай бұрын
🎉
@sammdohc
Жыл бұрын
My boot just split too, great video!
@hansgarage1751
Жыл бұрын
Thanks Samm!
@petervandervelden5747
8 ай бұрын
thanks. good video
@hansgarage1751
8 ай бұрын
Thanks Peter!
@leerowe5469
Жыл бұрын
Make sure you land the outboard splines (don't have to be to spec torque but make sure that it is at least finger tight) and put the suspension back together BEFORE reinstalling the 10 mm triple square bolts. If you tighten the 10 mm triple square bolts first and then work the outboard spline into its whole you run the risk of overextending the inner CV joint and dislocating the balls (not that I would do something so stupid). I managed to turn a 1.5 hour job into a 3.5 hour "learning experience".
@hansgarage1751
Жыл бұрын
Good tip! Thanks!
@eddyjawed
2 ай бұрын
what is the correct term used for those 'triple square bolts'?
@hansgarage1751
2 ай бұрын
I think that is correct. Here's a quote from Google "Triple square drives are used in high torque applications, such as cylinder head bolts and drive train components. Triple square fasteners are commonly found on German vehicles such as Audi, BMW, Mercedes, Porsche, and Volkswagen."
@eddyjawed
2 ай бұрын
I just had my axle ruined by a dodgy cv boot replacement. I think i'm better replacing entire drive shaft
@hansgarage1751
2 ай бұрын
That's unfortunate.
@porscheDIY
Жыл бұрын
Thanks… Good video. There are more similarities between the Audi Q5/SQ5 B8 and the 2016 Macan, than it would be between the Macan and the Cayenne. You probably find a lot of videos related to Audi Q5/SQ5 out there. Most likely axle shaft are exactly the same between Macan and Q5/SQ5 B8. For example: kzitem.info/news/bejne/2WuV4GmMgYaIf2U Also, for center bolt, always use a new one because is torqued to yield. The torque is actually 200Nm (148 lb-ft) + 180 degrees final tightening. Got those specs from manual. You can watch my bearing replacement videos… I used a torque multiplier wrench: Front Wheels Bearing Replacement - 2015 Porsche Macan S kzitem.info/news/bejne/jo57umhqj6uDhXo
@hansgarage1751
Жыл бұрын
Excellent note. Thank you!
@porscheDIY
Жыл бұрын
@@hansgarage1751 Thanks for doing this! I’m going to use it as reference if I ever need to change mine..
@hansgarage1751
Жыл бұрын
@@porscheDIY you're welcome
@regal953
Жыл бұрын
That big bolt is typical VWAG hardware as the suspension
Пікірлер: 25