You don't need that special tool. All you have to do is put electronic brakes into service mode.
@rayjones5157
Жыл бұрын
On my car they still did not retract fully. Had to turn them all the way in
@maxarothdev7374
Жыл бұрын
How do you do this
@JS416
Жыл бұрын
Didn't apply grease to guide pins, brake pad ends or back of pad. Isn't it going to squeek a lot?
@tcmautosalesllc7994
Жыл бұрын
It is recommended on this vehicle I did not and 10 miles later no squeaking. Still I would recommend…thanks!
@mikeglover7456
6 ай бұрын
You do not need the special tool. All you have to do is put it in maintenance mode on your - and you can push it in as normal.
@erick_s550
Ай бұрын
For cars with Electric Park Brakes. Put it into service mode and you can literally push the piston back in with your finger. No need for that tool, you run on the risk of damage. No scanner required either on Fusion there's a procedure do put it into service mode in the owners manual. Never use force on electric park brakes.
@JULITOPLAYS
Жыл бұрын
Thank you for this video I was about to drop $500 to have a mechanic fix it but I just searched up all the tools and everything turns out to be under $150 thank you!
@directedbytalon
Жыл бұрын
500 to have your brake pads replaced? that mechanic is robbing you
@jpdinosaur
Ай бұрын
@@directedbytalon I got the same quote today for just the rears. over 500. It's bonkers out there.
@daviedmx38
2 ай бұрын
can you use a c clamp instead of the caliper tool?
@tcmautosalesllc7994
2 ай бұрын
@@daviedmx38 Hi, it calls for a caliper tool so I would not risk using a c-clamp…the tool is free with deposit at any auto parts store.
@daviedmx38
2 ай бұрын
@@tcmautosalesllc7994 Thanks
@blkbltz3d
Ай бұрын
Cant you just use a clamp instead of the special tool?
@juantrainsmartnothard3505
2 жыл бұрын
Thank you so much! Saw 2 other videos and no one mentioned rhe special tools. Started the job and had to quit half way. Will rent it tomorrow. Also purchased a kit from Amazon but it arrives on the weekend. Appreciate your thoroughness!
@cornerbck38
2 жыл бұрын
45 torq for caliber bolts
@peeepeeepoopooo7541
2 жыл бұрын
When those things rust inside, they're a pain to take off without snapping them
@jayoliver7153
Жыл бұрын
What size hex key? Or Allen wrench?
@killzone1o3
18 күн бұрын
Bro why you so nervous
@mrsamsung8184
Жыл бұрын
Get so many different procedures for doing the rears pads on fusions I try the emergency brake procedure thing in the freaking piston came popping out cuz I wasn't watching what I was doing and I have the toolkit like this but then you get people that say you don't need the toolkit you do it by doing the emergency brake procedure but when I was doing it the Piston was not going in it was coming out
@JCSIspired
Ай бұрын
Hey man I'm going thru this right now. What did you do? My piston came popping out? How did you get it to go back in?
@matthewsetzer9896
Жыл бұрын
Thanks for the video brother ,God bless from Missouri
@Zizie_sc
Жыл бұрын
Dang.. I need one of those piston jigs. Makes the job so much easier.
@parrishgoodwin9874
6 ай бұрын
Thanks
@eddiecooper5986
3 ай бұрын
Dont the two indentation on the piston you turned in have to be in a certain alignment
@tcmautosalesllc7994
3 ай бұрын
Hi and thanks you would need to research that one but in my experience has not been an issue
@waynesalekin6773
Жыл бұрын
Great video. Thank you very much
@matt8863
2 жыл бұрын
You didn't have to put the vehicle in service mode?
@mrsamsung8184
Жыл бұрын
I did the right rear on the exact same car without doing the emergency brake procedure I just had the tool to spin in the calipers and then I went to the left rear and it would not go in all the way ended up having to get a freaking caliper because I saw the procedure for the ebrake and when I was doing it the Piston wasn't going in it was coming out and I was doing this by myself and the next thing you know the Piston came falling out and brake fluid everywhere and I had to get another caliper
@mrsamsung8184
Жыл бұрын
So I guess you can do it either way I don't know why these cars are so freaking complicated I've done hundreds of brake jobs with that tool I've never run into a problem except with a 2015 Fusion SE
@larrywhite-tk7ve
10 ай бұрын
Ok sorry I was rough on ya brother
@supspud
Ай бұрын
@@mrsamsung8184So you did or didn't do the e brake release procedure?
@rauldavila188
2 жыл бұрын
Thanks for the video really helped me out .👍
@kylerayk
8 ай бұрын
CaliPer, CaliPer, CaliPer! Caliber is the size of a bullet. Please do tell where the 35mm torque tool is used. What size allen wrench? Inch or metric? So do I just go into Auto Zone and ask for a "rental kit"? Last I checked, they had a whole shelf unit full of "rental kits" for different things...ball joints, universal joints, steering wheel pullers, harmonic balancer pullers, and many others.
@tcmautosalesllc7994
3 ай бұрын
Hi yes just ask autozone or parts store for brake caliber kit and they will provide the correct one
@SergioHernandez-yp7hd
2 жыл бұрын
how to disable the rear brakes
@jayoliver7153
Жыл бұрын
What size hex key?
@windynabbie
Жыл бұрын
I believe 7mm
@maxhuerta96
Жыл бұрын
The tools that you got did they come with the dura last gold box or no?
@tcmautosalesllc7994
Жыл бұрын
They were depart , required a deposit and once returned you get full deposit back.
@tcmautosalesllc7994
3 ай бұрын
Duralast box only included brake pads and rental kit was separate you pay a deposit and it is refunded when kit is returned
@Сява-щ5ы
2 жыл бұрын
Good video but you don’t need a special tool to get calipers compressed, you can use a C clamp for that which is pretty cheap
@circusclown9690
Жыл бұрын
These pistons on the calipers turn instead of being compressed with a C clamp
Пікірлер: 47