Learn how to install your 2017 GMC Yukon XL rear bumper cover. This larger rear bumper is pretty easy to work on but the parking sensors and may brackets can be a headache.
Where to purchase: bit.ly/17-20Yuk...
Source: www.revemoto.com
0:00 Start
0:23 Intro
0:46 Install the bumper accessories
2:28 Step pad install
3:12 Lower valance install
5:11 Parking sensor module install & harness
7:21 Parking sensor install
8:51 Mount the rear bumper
12:22 Tow hitch cover install
12:57 Outro
Thank you for stopping by to watch our GMC Yukon XL rear bumper cover installation video. This bumper really hasn't changed much in style in some time. The older Yukon rear bumper covers are similar in style but may vary in length or bracket positioning. Also, this video can work un almost all the GMC brand SUV rear bumpers. The Cadillac Escalade, Suburban, and Tahoe all have similar styles/shapes, and a lot of the bumpers are the same across several years/models. We tip our hat for GMC being lazy, or genius for keeping a lot of these rear bumper covers the same.
TOOLS NEEDED:
You will need a 10mm & 8mm socket wrench, a panel clip removal tool, or a flat-head screwdriver for the clips. You will also need a T30 bits hex key for the top bumper bolts. You will need a rivet gun, pneumatic or handheld with rivets.
PROCESS:
Hopefully, you watched the previous video on how to remove the GMC Yukon XL rear bumper cover. If you are one of the unlucky ones to completely be missing your rear bumper, you're in the right place. No bumper comes with the accessories pre-installed. This bumper has about 6 major pieces that need to be attached. We started by getting the most annoying piece out of the way, the tow hitch bracket. This piece is riveted onto the bumper. Very easy to do, just insert the rivets into the gun and compress it until it snaps. It's definitely more annoying to drill them out but they are very sturdy and easy to install. You can purchase a rivet gun kit at your local hardware store for around $20. Then we proceeded to install the top pad and lower valance. Both these pieces snap into the bumper and should pose no problems. The lower valance has this bracket that is best removed before installing it. It just makes life go a bit easier. They are held on by small circular steel clips. Just gently and slowly pry these up with your flat-head screwdriver or panel clip removal tool. Now you can install the parking sensors and harness to the bumper. This should easily attach or snap in place if you didn't break anything during the removal process. If the harness cannot snap-in, you can always tape it to the bumper. There is one module for the parking sensors that is also riveted on but it's only one rivet, and it should not slow you down. When installing the parking sensors, be sure to install the rubber liners correctly. There is a rubber liner for the parking sensors that will hold the sensor in place when you drive. They can easily get twisted out of place when inserting the sensor into the circular opening. Now you can mount the rear bumper to the SUV, but don't forget to plug the sensors back into the main wire harness. Once you get one side snapped in, secure the bumper with one of the top bolts to make your life a lot easier. Move your way to the fender liners and secure the bumper there before finally bolting the bottom of the bumper. Lastly, you can now snap your tow hitch cover onto the bumper, and voila! You have installed your GMC Yukon XL rear bumper cover.
Follow Us on:
FB: / revemoto
IG: / revemoto
Twitter: twitter.com/re...
_____________________________________
#YukonXL #Yukon #GMCYukon #DIY #revemoto #paintedautoparts #HowTo #GMC
DISCLAIMER: While ReveMoto tries to make the information in this video as accurate as possible, we make no claims, promises, or guarantees about the accuracy, completeness, or applicability of the content. No information contained in this video shall create any expressed or implied warranty or guarantee of any particular result. All do-it-yourself (DIY) projects entail some risk. It is the sole responsibility of the viewer to assume this risk. ReveMoto is not responsible or liable for any loss, damage (including, but not limited to, actual, consequential, or punitive), liability, claim, or any other injury or cause related to or resulting from any information posted in this video.
Негізгі бет 2017 GMC Yukon XL rear bumper & parking sensor install | ReveMoto
No video
Пікірлер: 9