Finally! Someone shows the entire process! Bravo my friend. Very helpful.
@nelsona779
3 жыл бұрын
Glad you could find it useful 👍
@veryconfusing
Жыл бұрын
That was SUPER HELPFUL ! - Thank you for posting. I have seen two others so far that did not point out that you can punch out the little spots to get to the clips - that makes this whole job easy !
@MatrixAlphaCWX
8 ай бұрын
Best video i found! Thank you! Made it a simple process! All the other videos they tore out and dissasembled everything.
@DavidEDebus
3 жыл бұрын
Thank you so much! The jeep dealer wanted $700 to replace the door watch cable. I was able to get it done in about two hours. The part only cost me $40. Thank you so much for this video. It made it possible for me to do this myself
@nelsona779
3 жыл бұрын
That's awesome 👌 glad my video helped. Its also good to save money. 😎 enjoy your weekend.
@Pearljammin56
3 ай бұрын
Got me thru it! My panel had to have the access holes cut out, and a 8mm nut removed from the upper right access hole (remove rubber Plug). Thanks for the great vid!
@jlfuse2834
Жыл бұрын
We had an additional step of removing an inner screw on our 2012 for to remove the panel. Learned the hard way because we broke mechanical plastic bracket on our first door.
@Pearljammin56
3 ай бұрын
Yup. Luckily I saw that in another video prior...
@drewb5738
2 ай бұрын
On my 2012, there was one more nut to remove that was behind a black rubber plug located about 6 inches above the door latch on the interior side of the door (opposite side of the door handle). I had a really bad rattle somewhere in my door and it magically went away when i put the door back together. I have no idea how i fixed the rattle but thanks for the helpful video.
@mikecates619
3 жыл бұрын
Thanks man this saved me a ton of headaches!!!
@nelsona779
3 жыл бұрын
Glad the video helped 👌🤟😎
@johngranato2673
8 ай бұрын
Thanks a Million
@jonathanpartridge8155
3 жыл бұрын
Very helpful!!! Thanks much for the info
@yukon2159
6 ай бұрын
Thank you brother.... This video is a great help!
@adrienrivero4375
3 жыл бұрын
Good Job. Great explanation. Extremely helpful. Thank you
@nelsona779
3 жыл бұрын
😎👍🏽 glad it helped.
@arthurquinlan3862
2 жыл бұрын
Perfect! I was able to fix my manual door lock (one M5 screw had fallen out, and the only way to get at the specialty screw was to remove the inner door trim) thanks to your complete instructions.
@sergioibarra3499
3 жыл бұрын
Thank you ive been looking for a video to do this need to change out the cylinder to jeep since we replaced the door due to a roll over
@nelsona779
3 жыл бұрын
You're welcome and glad I could help ✊🏽😎
@Marco00070
9 ай бұрын
Thank you
@mitomr.twiceasnice4358
4 жыл бұрын
They hide screws everywhere nowadays. Thanks for the upload.
@nelsona779
4 жыл бұрын
Yes they do!It's not as easy as it used to be, Not that it's a lot harder but the simple design went away. Thanks for stopping by bro.
@hailiepeterson2393
3 жыл бұрын
Now how do you put it all back together
@nelsona779
3 жыл бұрын
Reverse the process 😎✊🏽
@timparrott775
2 жыл бұрын
Thank you, When I got to the point of removing panel the plastic piece on the acuator seemed to be attached to the door handle and lock and it did not just slide out? Did i miss something
@Pearljammin56
3 ай бұрын
There is an access hole behind the rubber plug (upper right) 8mm bolt
@connor7877
2 жыл бұрын
What extra steps would one take to remove the glass from the door
@mongaragedecarrosserie1827
2 жыл бұрын
Merci beaucoup
@yogotro
Жыл бұрын
Nice, this worked perfectly, thanks for the info.
@user-gz5di3py9m
9 ай бұрын
I have question for anyone that knows….in the bottom front of the door, just below the strap, is a bolt. What does it do? Mine is missing and I have a rattle behind it so apparently it homds something in place
@tbozf4izzle
3 жыл бұрын
You rock!! Big jku jeep wave from Tazewell Tennessee 37879
@nelsona779
3 жыл бұрын
🤟😎🤜
@WeSuckAsHumans
Жыл бұрын
Aww was hoping to see full removal of rear inner panel....mine is hanging up somewhere
@mathewmaldonado3570
4 жыл бұрын
That's what's up homie
@Alhammadi-gy5jb
3 жыл бұрын
Thanks for the video
@chekovelazquez9133
3 жыл бұрын
could you do a video how to put back the glass? thanks
@nelsona779
3 жыл бұрын
Make sure its on the window channel and slide up tape to top part of the door to prevent the window from sliding down, slowly but everything back together and slide down the window on to the clips.
@johnnymacleod9559
Жыл бұрын
Thanks bro i was going loco
@usedtobekye9310
4 жыл бұрын
Nice homie
@nelsona779
4 жыл бұрын
Thanks!
@JayWhite124
3 жыл бұрын
How do you rock the window out? I’m trying to replace my glass but I can’t get my old window out.
@nelsona779
3 жыл бұрын
Slide it from the top if not attached to anything
@refugiolopez6194
4 жыл бұрын
Cool bro.
@nelsona779
4 жыл бұрын
Thanks for stopping by bro I really appreciate it😎
@JohnnyG1956
3 жыл бұрын
Are there clips/rods for the outside door handle and lock?
@nelsona779
3 жыл бұрын
Yeah depending on what model you gonna have one rod and 2 nuts or bolts
@JohnnyG1956
3 жыл бұрын
@@nelsona779 Thanks! It is a 2016 JKU Rubicon Hardrock. The nut at the top of the lock assembly released everything.... I didn't have to mess with the rods. The problem was that the door would not unlock (or lock) all of the time and you could hear a buzz from around the latch assembly. I took the panel off and cleaned the latch/lock assembly. Now is seems to work but there is still a slight buzz. I had the same problem a couple of years ago and the dealer replaced the lock assembly (or at least they said that they did.)
@kdh3706
Жыл бұрын
The engineers that developed these kinds of door panels should be publicly flogged.
@seancalverley4709
2 жыл бұрын
The worst design ever. Could they make it any more complicated, shit
Пікірлер: 53