Thanks a lot! 🔥 Not Many techs will show failure.. thanks for showing us the good and bad. 💪🏾
@BestCarFixes
Жыл бұрын
No problem 👍
@kwamesuniverse
Жыл бұрын
Agreed
@ramonmcgee2240
Ай бұрын
Will Autel do this via OBD2 for pre-2015 Land Rovers? I am looking to do this for a 2012 RR Sport HSE Lux and a 2012 RR Sport HSE.
@jorgemat8080
2 жыл бұрын
Autel can do it on bench. Choose write key and it will guide you through the steps of removing and soldering the wires so you can add key.. then choose read and check if it's unsecured or secured then choose the one that you read of the two and add your key..
@tjrufu01
Жыл бұрын
Hi is there a way to know if it’s secured or not before soldering on these ones with crystals
@jorgemat8080
Жыл бұрын
@@tjrufu01 yes plug in obd2 and try adding key if it fails there's your answer.
@tjrufu01
Жыл бұрын
@@jorgemat8080 ok thanks I tried on one it gave me the same screed unknown software version, so in other words…..on all unsecured ones keys can be added via obd?
@robertsalmons3344
10 ай бұрын
Unsecured may need to be done bench also. If it's after 15, plan on bench
@nomission4shure
Жыл бұрын
Thanks for the information my friend!! we from brazil and we got the same problem with a discovery sport 2018 its more complicated this atual versions Congrats!
@BestCarFixes
Жыл бұрын
you are welcome
@tommyherrera6456
22 күн бұрын
Yes, I have done it through eeprom & flash many times.
@RadovanPalik
8 ай бұрын
Abrites can do this via OBD (CAN wires under the seat). A special key from Abrites must be used.
@user-us1sf8id6u
Жыл бұрын
tell me, please. the lonsder device can subtract the id of an already registered key and write this id to a new key that has the function of changing the id. can't an autel device do this? that is, the function does not add a new id, but the previously recorded id passes into a new key.
@BestCarFixes
Жыл бұрын
im not sure but not all tools are equal
@user-hj4ft5cz9q
2 жыл бұрын
You need to do it on bench after 2015
@davidcain2985
2 жыл бұрын
those years range rover cannot add key via obd you have to do it via the RFA module. its more complicated requires soldering and removal of crystal on circuit board because the data is secured
@khalidmahdy804
2 жыл бұрын
You can do it via obd with lonsdor key programmer
@davidcain2985
2 жыл бұрын
yes i can be done with londsor but only with londsor simulator range rover key
@davidharutyunyan7244
Жыл бұрын
Can you please help me with HPLA-19H440-BD clear file, I need it can somebody help me?
@OnyedireChukwu-wt6ee
9 ай бұрын
I faced the same problem too
@user-us1sf8id6u
Жыл бұрын
you may have a video of how to add a new key by removing the block and reading data using autel. or if you succeed, record a video of how to do it. thanks
@BestCarFixes
Жыл бұрын
not yet but if i get a chance i will do it for you
Пікірлер: 30