Thank you so much brother you literally taught me how to do my brakes.
@XxDOECOMExX
3 жыл бұрын
This video helped a lot thank you so much. Just replaced my breaks today
@stevealsip3045
Жыл бұрын
You don't have to remove the top bolt from the caliper,only remove the lower one and it will just pull up...10 min tops
@mechanicallyinclined2715
Жыл бұрын
You should remove the top bolt, too. These bolts have to be greased... if you don't grease them, they will eventually get jammed, and you will have to replace the bolts after fighting them for whole day ... all that time you saved will be for nothing ...
@geno5592
Жыл бұрын
There's more to it. And there is other easier ways to do it too. But thanks for sharing your way I enjoy watching it 👍
@anuheasapla5629
27 күн бұрын
Thank you for sharing the knowledge
@bassamabdelnabi3117
2 жыл бұрын
Thanks so much. May God reward you for posting this video
@ramiroserrano4219
2 жыл бұрын
Thank you for the video was able to do my brakes on my own saves a lot of money 👍😀
@El-Arca_Del-Pacto
9 күн бұрын
Great video man
@imbogfootstrato
3 жыл бұрын
not bad. but you should always get the rotors resurfaced by orielys, a resurfacing shop or buy new rotors. those brake pads are not gonna seat in properly. which in return they dont last as long and warping occurs quicker. plus you dont stop as good. its just more money down the drain and should be done right the first time
@klrdto3250
9 ай бұрын
Are the rotors damaged? The back I assume...?
@RealX-Benz
6 ай бұрын
This is 60% an excellent video and 40% is a disaster and the disaster is that guys to eliminate vibration or any complication is your brake system go to the nearest parts shop and take out the rotor and ask them if they could resurface it for you the price tag goes between 10 to 40 bucksgive that money get your rotor as a brand new put it back in again and install the brake pads and push back your piston and everything
@LarryB-inFL
Жыл бұрын
What about measuring the caliper thickness? What minimum thickness are they supposed to be????
@countsvalable
2 жыл бұрын
Great video I’m ready to try change brakes thank you
@DGOV-zg9px
Жыл бұрын
Great video, but do you have to go a certain order, passenger front first,than driver side, back passenger side, than back driver side. ?
@bob123281
4 ай бұрын
No doesn’t matter. Only when flushing brake fluid u have to do it in a certain order
@franksedlar4795
3 жыл бұрын
Thanks for the video. What kind of grease are you putting on the caliper pins?
@mechanicallyinclined2715
2 жыл бұрын
Synthetic break grease
@seanstrickley3992
Жыл бұрын
Where is the part that u have to disengage to the brake systems back brakes?
@nicandriestevez8444
Жыл бұрын
Thank you for showing us i appreciate you
@nicklanderos3773
2 жыл бұрын
Thank you sir for the video! Much appreciated
@mannyclemente7159
3 жыл бұрын
Thanks for your informative video!
@melvinyang3041
2 жыл бұрын
Thanks for the video bro! Much appreciated
@Kaliguy88
Ай бұрын
Are the 2018 xse and se the same pads and rotors...I am trying to buy then on Amazon but the xse is not included with the other trims
@danquinones9898
Жыл бұрын
good work! please be safe and use a jack stand next time.
@edbtzkhud
2 ай бұрын
You forgot to put the warning bracket on the pads
@user-me1zc6wy4q
6 ай бұрын
When I try to compress the break it’s way to hard what can I do to lose that part when I use the compressor tool
@aksub.4316
Жыл бұрын
Nice job,good process.
@vermontvermont9292
Жыл бұрын
I'm about to start this job at 5:43pm lol..
@ckim1984
3 жыл бұрын
what is the name of the push tool? and what else do I need for the job? what is the name of fluid on bolt?
@stefanchulakov5682
3 жыл бұрын
the tool is called "disk brake pad spreader" and the fluid on the bolt should be "anti-seize lubricant"
@stefanchulakov5682
3 жыл бұрын
also the other way to do it is you putting 1 of the old brake pads on the caliper and hit with hammer!
@rafaelvictoria8593
3 жыл бұрын
Is it Necessary to push in the piston like you did in the first caliper ? ( studying ur video getting ready to do my own breaks on my 18 Camry)
@mechanicallyinclined2715
3 жыл бұрын
Yes you have to press them in otherwise new brake pads won't go on the rotors easily
@seanstrickley3992
Жыл бұрын
Ok well before u do anything disengage the brake system guys. Get in the car the parking brake in middle console u have to click up 3 times then down 3 times on the 3rd time clicking down hold it till the parking light blinks slowly on the dash and then do your brakes then when done do this again to reengage brakes
@mechanicallyinclined2715
Жыл бұрын
That's only for electronic parking brakes system... this one didn't have electronic parking brakes
@seanstrickley3992
Жыл бұрын
@@mechanicallyinclined2715 yes sorry that's true and correct
@klrdto3250
9 ай бұрын
@@mechanicallyinclined2715 how do I know if my camry has it or not?
@DakhilB
Жыл бұрын
Great job Brother
@isolaoluwaseyi
3 жыл бұрын
Is it the same process with 2020 Toyota camry Le?
@TheHottestOut23
2 жыл бұрын
Yes
@bobit8742
11 ай бұрын
how you put the rear brake in service mode?
@Jnlix_Cvstrx
8 ай бұрын
DG1212 doesn’t fit 2018 according to autozone. Its DG1879 i believe
@mechanicallyinclined2715
8 ай бұрын
Yours could be different trim then whats in the video
@Jnlix_Cvstrx
8 ай бұрын
@@mechanicallyinclined2715 2014 Camry SE
@awesomegaming1754
5 ай бұрын
Very helpful
@jack8356
Жыл бұрын
Looks to me that your rotors was never broken in properly. I bet your probably get a little vibration when stopping
@mechanicallyinclined2715
Жыл бұрын
No vibrations... rotor do have groves
@a_k1988
3 жыл бұрын
Thanks for you
@gomezbrian77
Жыл бұрын
What about the rotors ?
@arazking80
3 жыл бұрын
I have a question when to replace paint break in a car........?
@mechanicallyinclined2715
3 жыл бұрын
Paint break ... what is that?
@countsvalable
2 жыл бұрын
Can you do rotors video
@krazziejrboi
11 ай бұрын
Ty
@danieltico2604
3 жыл бұрын
Thank you 🙏
@Wesmancan
2 ай бұрын
Good videos start with a tool list. I’m out n
@edward5710
3 жыл бұрын
Thank you aper
@linusmethtips90
Жыл бұрын
Thank you Boss
@andersonrodriguez8258
3 жыл бұрын
Add brake fluid ?
@oserratos
2 жыл бұрын
So i noticed you didn't put the brake system in service mode. Is that really necessary?
@Thebeevas
Жыл бұрын
Only with electronic E-brake.
@sshowtime2k
Жыл бұрын
So I have electronic E brake what’s my first step
@Eertios
2 жыл бұрын
Thanks man!
@AwWwWwWwWyA
Жыл бұрын
when compressing the piston do you have to open the brake fluid cap?
@floridadog7773
Жыл бұрын
Yes and leave loose on top
@AwWwWwWwWyA
Жыл бұрын
@@floridadog7773 perfect so that's it do i have to bleed the air out as well?
@jack8356
Жыл бұрын
No you dont have to open it. Its better if you dont. When you open it you introduce moisture into the system.
@AwWwWwWwWyA
Жыл бұрын
@@jack8356 I ended up not opening them and it has been completely fine. probably when I change out the front brakes ill do a bleed
@diald009
Жыл бұрын
good thanks
@georgesanchez7048
3 жыл бұрын
What size tool do you need for the bolts?
@jamrs12
3 жыл бұрын
14mm
@chanalsonnent
3 жыл бұрын
How much miles was on it when you replaced break pads ?
@mechanicallyinclined2715
3 жыл бұрын
60k i believe
@dumbeezy5480
2 жыл бұрын
Mileage can be irrelevant sometimes. Better to take a look at your pads and rotors.
@user-kj7nh7oe3g
Жыл бұрын
Fat name please?
@dakillaisme21
3 жыл бұрын
You don’t have to bleed it like the typical process?
@mechanicallyinclined2715
3 жыл бұрын
You can bleed it if the pedal is spongy... if it isn't you don't have to ...
@reyluque7430
3 жыл бұрын
Thank you for the video. I bought everything at the dealer but didn't know about greecing the upper and lower bolts.
@CMDR_Birb
2 жыл бұрын
Always bleed every 3 years, 5 max.
@klrdto3250
9 ай бұрын
@@CMDR_Birb bleed what exactly? Change the entire brake fluid?
@dfhhtyu3434
3 жыл бұрын
Should of use akebono
@mechanicallyinclined2715
3 жыл бұрын
Yes they are good... but my friend bought the brakes ...
@kuva2012
2 жыл бұрын
Man after watching this video I feel like drink a bottle of whiskey, can you ask your wife or boyfriend to hold that stupid phone? And by the way you don't really have to remove both bolt just only one and loose the other one
@mechanicallyinclined2715
2 жыл бұрын
You should remove both bolts and grease the caliper pin every time... they start to fade the brakes unevenly if you don't... and if you saw the video i had the camera on stand a few times too but to show the bolts or things closely I have to handle the camera...
@traceurernest2222
2 жыл бұрын
Booo hoo go cry about in your closet
@joevallini7170
Жыл бұрын
KVN Please post the link to your perfect video on how to do this. This gentleman did a great job 👏
@Slime_Lizard
Жыл бұрын
you ain't on shit @kuva2012
@wicked1rish
Жыл бұрын
Dude my caliper is not moving at all and it's not rusted.... both bolts have been removed and it refuses to budge. What am i doing wrong?! This is for the rear
@mechanicallyinclined2715
Жыл бұрын
Sorry for a late reply ... maybe your electric brakes are on ... you need to disengage them first
@NorthPhilly4life
Жыл бұрын
I have a XSE what’s with the electric brakes I keep getting asked about.
@mechanicallyinclined2715
Жыл бұрын
Sorry for late reply ... you have to disengage the electronic parking brake ... hold up the disengage button for 3 seconds... it should do it ..
Пікірлер: 92