argh I watched this hoping to see how in the heck to torque the rear caliper bolts. How the heck do you fit a torque wrench down there without a high lift?
@knsbrakes608
3 ай бұрын
I dd not know that was an issue
@superameric8
4 жыл бұрын
Well done
@williedavismckennie5334
4 жыл бұрын
Great job
@TierOneLandscapes
Жыл бұрын
I used a little Blue Loctite on my C7 break caliper bolt threads. Was that unnecessary or overkill?
@ernest6980
4 жыл бұрын
Good job only one ☝️ thing GET THE RUST off and put anti seize on
@skippynj1979
Жыл бұрын
Was wondering about that🤦
@kennethhu9170
2 жыл бұрын
Love the video I was wondering if these fit on a non Z51 c8
@salvatorecacopardo5460
2 жыл бұрын
You need to change your calibers to Z51 calibers .
@alexpaic2984
2 жыл бұрын
It will just fine but you would have to replace the calipers also
@salvatorecacopardo5460
2 жыл бұрын
How did these hold up with track use ?
@cesarjara6192
Жыл бұрын
no bleeding of the brakes?
@jameshockenberry7030
Жыл бұрын
I want to change rotors on 23 non z51, wasn't the parking brake engaged automatically, how did you remove it? Thanks
@kennethkozlowski5100
Жыл бұрын
Disengage parking brake with the button while in park - then disconect the battery.
@fgburrell
Жыл бұрын
Those rotors are directional. I was under the impression they went the other direction. I could be wrong. 🤔
@knsbrakes608
Жыл бұрын
They are directional. The inner vanes determine the direction of rotation not the slots. These are installed correctly
@stevevelarde6612
3 ай бұрын
Why do you need to disconnect the battery?
@knsbrakes608
3 ай бұрын
If there is no brake pressure i.e. when pump up the pedal after a brake install the car will throw codes and go into limp mode which can be hard to clear
@stevevelarde6612
3 ай бұрын
@@knsbrakes608 Thanks, Ken!
@DeanFetterolf
4 жыл бұрын
When you disconnect the battery do you loose all of your driving presets and audio channels?
@brandonnixon7105
4 жыл бұрын
Shouldn't. Their is a separate mini battery to save that stuff.
@edwardryan2200
3 жыл бұрын
Caliper bolts torque to 140.....think it's supposed to be 160...... can there be that much difference?
@knsbrakes608
3 жыл бұрын
I don't recall if we had verified service manual information at the time of the video. It's brakes so I 100% defer to published service manual specs.
@redLeader1686
7 ай бұрын
I found a couple of spec's that said it's closer to 85ft lbs for the rear caliper bolts - including the paragon performance how to on youtube.
@joegutierrez5202
2 жыл бұрын
NOV-2021 --- 1800 for 4 pc
@maxfly7079
3 жыл бұрын
How much weight did you save per rotor?...thx
@knsbrakes608
3 жыл бұрын
About 4 lbs per front and 5 pounds per rear
@maxfly7079
3 жыл бұрын
@@knsbrakes608 nice, large amounts of unsprung weight makes the suspension and the driver very happy.👍
Пікірлер: 28