Love me some two stroke videos. MXA your articles and website helped me survive the boredom of a year long deployment in the South China Sea in the navy 😂 for some reason your website would always load for me. I must have read every article and bike test from the last 10 years 😂
@jdub976
Жыл бұрын
Gas Gas seems to get the new stuff after the bugs get worked out. Nice bikes.
@northerntoyota7584
Жыл бұрын
This bike hits hard, put a JD jet kit in mine (needle makes the biggest difference, along with updated jet block gasket) can’t see how anyone would ever need more power unless wide open desert riding.
@andrewpereira1117
Жыл бұрын
Can you list the parts you got? I might get one tomorrow!!
@northerntoyota7584
Жыл бұрын
@@andrewpereira1117 I just went to JD jetting website and ordered the kit for the 2021 Ktm 250sx. They didn’t list a kit for the gasgas last summer. My jet oem block gasket failed after less than 5 hours.
@andrewpereira1117
Жыл бұрын
@@northerntoyota7584 another oem gasket ? Or different part number
@northerntoyota7584
Жыл бұрын
@@andrewpereira1117 it’s through jd. It’s a more ridged design that doesn’t fail.
@andrewpereira1117
Жыл бұрын
@@northerntoyota7584 appreciate the information 🙏 👌
@maxwelllittle3562
Жыл бұрын
love everything about this bike!!
@vintagetrikesandquads4012
Жыл бұрын
Love the red frame on the GG too. They should keep the carb--at least for a few more years. I thought the whole point of GG was to give customers options. Carbs are cheaper and much easier to tune. Maybe I'll have to get one before they change to fuel injection.
@Sleepy.Time.
Жыл бұрын
carbs are only easier to tune for people with experience using them, for the average modern day rider they are very unlikely to have a clue how to tune a bike using a carb let alone have a selection of jets and needles on hand
@Ray-ol8bx
11 ай бұрын
I couldn't find a good bike after covid so I got a low hour tpi and stock it was ordinary but after a ECU flash it's so dam good I'd find it hard to go back to carb and I'm a big fan of keeping it simple.
@evo5349
Жыл бұрын
The last of the old type 2 stroke instead of the nanny state new models Ktm's, I mean a rev limit on a 2 stroke, give me a break!
@rickstrom6097
Жыл бұрын
Nice! KTM and HUSKY will have better mapping next year guaranteed they basically created a whole new bike the future of TBI and fuel injection is brite for 2 strokes we can only dream at this point that they make a 450 2 stroke they will be whole shot masters.
@wmosman100
Жыл бұрын
I’m a bit surprised you weren’t racing the totally new KTM or Husky 250. Do you feel the previous generation platform of the GasGas is superior to the first iteration of the TBI bikes? And if so, in what area(s)?
@ottokirk2325
Жыл бұрын
Yup, the needle is a cheap and easy way to shape the PB to your liking. The smoother/linear may feel slower, but it is only perception and you will save energy, BTW. Personally, i'd be installing my spare Keihin 38mm AS with an old quad tapper Suzuki or JD needle. I might even install the STIC metering block carb insert. 20 minute install and it's like porting with a 25+ CC big-bore kit. May need a throttle tamer, retard the timing, -2 teeth at rear or a 110/90 and an 11oz FWW. It will have more over-rev and be a short shift beast at the same time. Ask me how my STIC'd 200SX runs with these changes.
@Doc-jw4iy
Жыл бұрын
You got a part number for the return spring from Honda?
@tattol7723
10 ай бұрын
Do you have the part number return spring honda?
@spacejaime
Жыл бұрын
Josh - what's the peak h.p. reading on Mitch's dyno?
@scottphillips445
Жыл бұрын
I would like to know what modifications were made prior to the smoker national
@MrSuperflydude
Жыл бұрын
I really hope the next ones don't look like the factory edition
@mixerguru
Жыл бұрын
uh? do you mean "forged " or "cast" are the CNC clamps made from forged aluminium stock or cast? CNC'd doesn't determine the density which would dictate the flex from the piece . a forged part would be the strongest CnC machining would be the most precise shape (hopefully) it could be either cast or forged
@Robledo_Moreira
4 күн бұрын
❤
@alexarmstrong1134
Жыл бұрын
2023 Gas gas vs KTM 250? 🙏
@rudolphhessian4183
Жыл бұрын
air forks was all i needed to hear to switch vids and look at a different bike. Want oil hydraulic forks, air can leak out very fine to tune.
@ryandragunas6798
Жыл бұрын
Could anyone tell me how much horsepower this bike puts out? I've been looking all over the place for that spec and cannot find it for the life of me..
@jg79100
3 ай бұрын
It should be identical to the horsepower of the 2022 KTM SX 250, which has a listed HP of 49.23.
@ottokirk2325
Жыл бұрын
I wish there were more in-depth reviews. Thankful for MA efforts, but they are like SX broadcasts, geared to noob-ish riders. Ya can't geek out on this stuff.
@lel3972
Жыл бұрын
There are any difference from 2022 ktm sx 250?
@ctrott4824
7 ай бұрын
How does this compare to a Yamaha YZ250
@SpeedDemonExpress
Жыл бұрын
I don't think the new 300sx needs a new map. It's already fast. I have 23 hours on mine. There's no problem with the engine power at all.
@bugs7425
Жыл бұрын
Which Honda model/year rear brake spring?
@christophe2591
Жыл бұрын
Ah ah ah !!! : Tester des " kt gas ou des husk tm ... " Ça c'est du bon boulot , vive la mondialisation . ( Moi je retourne à mes vidéos des GP cross 86-95' ... )
@CoolcatAMA-Pro
Жыл бұрын
No more calloused fingers
@AmpAHolic-wn6mr
Жыл бұрын
Gotta get rid of those 4 stroke background fart sounds throughout the video. They ruin everything.
@mouthofpower8492
Жыл бұрын
i'd buy em all like crazy if they just put showa or KYB springs on them. waste, so sad
@Kawiboy
Жыл бұрын
✊👊✌️😉
@lawrencemacdonald-yz4vn
9 ай бұрын
Just a cheaper ktm 😂
@thomasrenfrow609
Жыл бұрын
If I'm gonna spend this amount of money it won't be for a carbed bike.
@jpesicka492
Жыл бұрын
It's a 2 stroke. It's ALL about the carb.
@northerntoyota7584
Жыл бұрын
Bye Felicia
@googlesucks3520
Жыл бұрын
You can get a brand new mc250 for $6800. Thats less than I paid for my 2013 250sx brand new in 13....in a post covid world thats a steal and also proves you don't even know how much they sell for anyways you just wanna talk shit 😂
@racerx2580
Жыл бұрын
Obviously these new name/manufacturing companies are good considering the reviews of the bikes. I guess it's weird talking about something called GasGas. Not your standard Zuki, Yami, Kawi etc. My question is we know the Honda CR250 was the rawest 2 stroke ever. And the others have stood for so many years. I can't help but look at this bike as a "cheap knock off" lol. It's a shame what things have come to but I truly would like to have a GasGas MC250. It reminds me of the old school CR250's and the like. Thanks for the video on it. EDIT: He pretty much answered everything. Wow what a shame where things are headed.
Пікірлер: 44