Maaaan thank you for making this video I swear yesterday we were up till 2 am trynna figure out how the spark plugs go connected and thanks to you my good friend I was able to figure it out at 5:21 you da best!!
@tubejim101
3 ай бұрын
Glad the video helped :)
@arriristov4960
3 жыл бұрын
So I just took a couple photos, and figured that would be good enough. Not even close. You're a lifesaver man. Thank you so much!
@nohabloemojislosiento4930
6 жыл бұрын
Getting ready to disassemble the top end to do the head gasket, and this video is a lifesaver. The intake side of a 22re looks so ominous with all the vacuums lines and stuff. Thanks for breaking it down where my Chilton manual didn't!
@tubejim101
6 жыл бұрын
No problem. If you get stuck. Will try and shoot a video explaining. Just let me know.
@greglamey6602
6 жыл бұрын
Will the fuel injection manifold off a 22 re fit on a carberated 22 u engine
@tubejim101
6 жыл бұрын
I would think the 22re would bolt to the 22r. Think you would want the change the whole head though.
@elitearbor
6 жыл бұрын
I just happened to be doing the same thing, four days after you posted your video! You saved me from having to try to video and/or label all the lines, thanks a million!
@tubejim101
6 жыл бұрын
Yesterday I was looking at it, to figure out how to put all those vacuum lines back :)
@mcvilllain
9 ай бұрын
Saving this vid for later, I pulled my clapped 22re to put in a good one and the intake wiring and vacuum lines look to be the most difficult part
@99fxr68
Жыл бұрын
Thanks for going down the line and naming all the vacuum lines. I just did my throttle body and my plenum looked as dirty as yours 😂😂 I just wanted to see if I needed any gaskets of anything. Great video
@coyotebrowntrouthunter
2 жыл бұрын
Super cool video man! I got a '91 Pickup and '90 4 Runner and need to do the same thing to the 4Runner. My fuel line from the filter to rail cracked on me the other day so had to order one off Ebay. So purchased the plenum gasket and all new Injector o-rings and seals as well. Now that I watched yer video, I'm contemplating whether or not to just buy a new EGR valve as well. I cleaned the throttle body a month ago and it was filthy dirty in there. I can't imagine how dirty the intake will look when I take it apart! LOL. Appreciate this video....thanks!
@nohabloemojislosiento4930
5 жыл бұрын
I want to thank you for this video. You posted this the day before I disassembled the top end of my 22re and it was a great help then. Now I've finally got it back together after soooooo much procrastination and I came back to this video and it helped even more. I deleted the EGR when I put it back together for the exact reason you wanted to clean your intake. My intake wasnt quite that bad but bad enough that I thought the EGR was doing more harm than good leaving all that carbon buildup in there. Definitely made sure to give the plenum and manifold a good cleaning.
@tubejim101
5 жыл бұрын
Glad the video helped out. Thanks for the feed back.
@israelroman9855
2 жыл бұрын
Thankyou for that video rigth now I'm doing that job to my pickup, my problem is the thermostat is very bad and i had to change the manifold intake very Hard to fine and i get one and i'm finishig the job, 8 of january 2022 Israel Roman from Puerto Rico nice video.
@UOfan714
4 жыл бұрын
Very helpful, thank you so much. I've learned a lot from your videos, having just bought a 1994 22RE and trying to get it up to speed
@snippits75
6 жыл бұрын
Good video! I did head gasket and timing chain kit just over a year ago, and I wish I had made a video. Luckily, I did take a bunch of pictures, so I got it back together just fine. Dang that cold start injector was really dirty. An injector shop can clean it, and get it to working like new. I did not do an EGR delete on mine because I had already spent too much money, and buying block off plates was just more money.
@tubejim101
6 жыл бұрын
How long did it take you to do the head gasket and timing chain kit. Been thinking about the timing chain. Figure if I go that far in, should do a head gasket too.
@snippits75
6 жыл бұрын
It took me a few days, but I am old timer now. Back in the day, I could have done it in half the time. A lift would make it go even faster. My engine had about 189,000 miles on it when I tore it down. Chain was slapping on cold start up, and the head gasket was bad because I was loosing coolant out of the exhaust. I bought an Enginetech complete cylinder head from RockAuto for $250. Just bolt it on. Local automotive machine shop that I trust had a five week wait on rebuilding my cylinder head, and I needed it done now, so I bought the Enginetech cylinder head. I used a Cloyes HD timing kit that has the metal timing guide on the drivers side. An OSK timing kit is what Toyota used on these engines, but it comes with the plastic guides. I saved a little bit of money buying the Cloyes HD kit plus I did not have to buy the metal guide. Cloyes makes good stuff. My plenum was not nearly as dirty as yours. I am thinking that your EGR valve is probably mostly clogged. The reason is mine was half way clogged with hard carbon where it bolts to the cylinder head. I cleaned it out with a flat head screwdriver, wire brush, and carburetor cleaner.
@tubejim101
6 жыл бұрын
Thanks for all the info. I have been seeing those cylinder heads for sale. They look like a good deal.
@flyprincess69
9 ай бұрын
I’ll be pulling mine next week to replace the lower manifold next week after buggering up an thermostat bolt I broke off. I wish they used anti seize back in the day.
@ourladyofperpetualmotion79
6 күн бұрын
Thank you so much!
@tubejim101
6 күн бұрын
Your welcome.
@mitchellmcmahon9969
5 жыл бұрын
I have the same motor and the same task ahead of me. Good idea to make a routing video.
@cbh148
6 жыл бұрын
My '94 4x4 5 speed Xtracab looked just as bad in the intake manifold when I removed it for the first time a year ago (~170k miles). The gunk is from the EGR valve. It took me a bit to figure that out since the gunk is heavy even up at the throttlebody, on the opposite end of the plenum from where the EGR connects. The reason EGR gunk is so far upstream is because the plenum has a passage running from the EGR flange up to right behind the throttle. I didn't notice it until I cleaned the inside of my manifold (which required oven cleaner). I didn't want that crud building up again since my pickup already consumes about 2 qts of oil every 3k miles, which is probably why the gunk was so wet looking. Plus I didn't want any higher chances of pinging on 87 octane since oil effectively reduces a fuel/air charge's detonation resistance, so I deleted my EGR before starting it back up again. Also deleted the PAIR system to further simplify things. So far so good.
@tubejim101
6 жыл бұрын
Have been thinking about doing that too. Did you buy a delete kit, or just make your own block offs?
@cbh148
6 жыл бұрын
+tubejim101 I bought the LC Engineering EGR block off plates (the one for the plenum, the one for the intake side of the head near cylinder 4, and the one for the firewall side of the head), then some cheap ebay PAIR block off plates (removed that tube above the exhaust manifold). Blocked off the port on the back of the intake box with a rubber cap for putting on the bottom of a chair leg haha. Also removed the charcoal canister and its vacuum solenoid on the valve cover as well as all the other solenoids up there other than AC idle-up (the grey one with grey plug you pointed out first in the vid). I won't claim that I notice a difference in how it drives, but the engine bay is much easier on the eyes and easier to get to that darn oil filter ha.
@seanchard9678
5 жыл бұрын
How much work was it preparing both surfaces for a new gasket? I have my plenum off the motor and just now taking steps to clean the carbon out of it. I tried throttle body cleaner, but at $6 a can it would cost me a ton of money and I can't really get to all the areas that need cleaning. Considering oven cleaner or a trip to a automotive machine shop to have them soak it.
@tubejim101
5 жыл бұрын
First your going to want to remover everything from it. You will have to reset your throttle position sensor when your done. I have a video on how to do that. The best way that I have found, is to take it to your local machine shop, and have them hot tank it. It should not cost that much. I did not find out about that option, till I cleaned it myself. I soaked it for a few days in SuperClean: amzn.to/2OWS6oq
@mikeporter7240
5 жыл бұрын
great vid ! I have a 1993 toyota 4X4 22re and I've been thinking about removing my intake. How did you remove all the carbon gunk ?
@tubejim101
5 жыл бұрын
Ended up soaking it it SuperClean: amzn.to/2PI7jPs
@mikeporter7240
5 жыл бұрын
how long did it take and how good did super clean do in disolving the carbon ? Thanks, mike
@tubejim101
5 жыл бұрын
If you use a toothbrush, it works pretty fast. Gas works good too.
@Samson-EC
3 жыл бұрын
Hey Jim, on your throttle body there are three vacuum hose ports. One goes to Charcoal and two go to EGR. What ports on throttle body did you attach them to. They are labled "P", "E" and "R". DO the lines match up with your vacuum schematic under the hood? Also what year truck is yours ? Thks...jc
@tubejim101
3 жыл бұрын
Hoping this video will help: kzitem.info/news/bejne/03-psKJ7saBmhGU My truck is a 91.
@Samson-EC
3 жыл бұрын
@@tubejim101 thanks for the link. That throttle body has 4 ports whereas mine only has 3. In addition I could not see the letter designator by each port so I am going to see if I can download the video and look. R U in calif because I have to deal with calif emissions? Thks again..jc
@tubejim101
3 жыл бұрын
@@Samson-EC no emissions, and no sales tax.
@Samson-EC
3 жыл бұрын
@@tubejim101Lucky you. Hate this crappy state ..jc
@elirenigar9357
5 жыл бұрын
The title is misleading because the intake manifold wasn’t removed.
@tubejim101
5 жыл бұрын
Think your correct. Still getting used to the Toyota engine.
@Community-Action
4 жыл бұрын
Wow, what is all that gunk from?? Looks like it’s worse in only two of the air inlets.
@tubejim101
4 жыл бұрын
Most of it comes from the valve cover vent, which goes into the throttle area.
@Community-Action
4 жыл бұрын
Did ethanol cause most of that?? It almost looks like someone put sugar in the gas tank. I have had several vehicles with 22RE engines and have never seen anything that bad
@tubejim101
4 жыл бұрын
@@Community-Action Had over 300 miles on the engine. It was a bad design that was forced on the industry for EPA stuff. Seems like 3/4 of vehicle repairs are related to EPA in some way.
@kullerbees323
5 жыл бұрын
What is the hose that is behind the oil cap on top of the engine at the beginning? I think it connects to the intake
@crisibarra1171
4 жыл бұрын
Did you ever find out what hose that is mine just broke
@billwithers7457
3 жыл бұрын
@@crisibarra1171 PVC hose. Small amounts of gasses slip passed the piston rings and down into the crank case. The gasses slightly pressurize the engine and the two hoses at the top vent those gasses back into the intake to be burned again and sent out through the exhaust.
@billwithers7457
3 жыл бұрын
I think your engine is burning oil. The burnt oil travels with the exhaust gasses through the EGR line and is injected right behind the throttle plate. This can foul up an intake manifold like yours is.
@okbye1
3 жыл бұрын
I have new 22re..it smoked on start after off overnight or hr or so. Did start with plugs out..nothing came out, also did bore scope with pressure on coolant..nothing in cylinders. What in the intake can cause these symptoms? If i pull the intake and look for coolant? Been going though hard times after putting out 3k. Engine runs great otherwise, although it seems to want to vapor lock on start after sitting all night.
@billwithers7457
3 жыл бұрын
@@okbye1 I am no expert, and you should certainly take everything I say with a grain of salt, but my first thought is a bad idle air control valve could be part of the problem if the problem only occurs on cold starts. The IACV takes a small coolant feed that adjusts the air flow through the throttle while at low temperature. This has the potential to cause all sorts of issues when faulty. It's relatively easy to get to and easy to replace. This will also let you check the throttle body and upper intake manifold for any obvious abnormalities like excessive carbon build up. All you'll need is a new throttle body gasket, which is like $2. If there's coolant in the intake... well, that's certainly not good. First I'd check your oil and coolant to see if either is contaminated by the other. I presume you've done that. If your coolant isn't contaminated and the cylinders are clear, it's probably not a headgasket issue. If the smoke is dark, it might be that your piston rings are too loose and oil is getting passed the piston at low temperatures, but sealing properly once at operating temperature. I would do a compression check to test that possibility. These are just the first thoughts I have and though I've owned a 22re for going on 15 years now, I am far from an expert at troubleshooting it. Before doing any engine work, please consult... someone or something more qualified than me.
@RODR0505
5 жыл бұрын
Where can I find the torques for the bolts? Thank you for your help. :-)
@tubejim101
5 жыл бұрын
amzn.to/2V1wrhW I think you can find the manual online for free.
@marlanamcvey6098
5 жыл бұрын
5:12 there is a grey connector top right of video. what is it and where does it go?? Me and my husband just fixed the intake and found that grey connector not hooked anything and cant figure out where it was supposed to go.
@tubejim101
5 жыл бұрын
Do you see it in this video? I think you are seeing an air conditioner connector. kzitem.info/news/bejne/03-psKJ7saBmhGU
@JesusHernandez-lv4rx
5 жыл бұрын
Marlana its a vacuum switching valve. If its a California emissions model it should have 3 of them. You’re talking about the bottom most connector ontop of the valve cover, and by that i mean the one closest to the engine cooling fan. The middle connector has a vacuum overflow exhaust port with a cap and the topmost blue connector ontop of the valve cover is the third vacuum switching valve (vsv). All 3 are vacuum switching valves (vsv) but have different part numbers and specific functions. It’s clearly outlined in the vacuum diagram on the hood. I know because I barely got done replacing the intake manifold gasket along with the gasket that was being replaced as shown in this video, which I would term the middle-of-the-intake-manifold gasket. Removing the entire manifold is more cumbersome in case you wanted to know.
@mariocastro634
2 жыл бұрын
Tienes video de como cambiar inyectores motor 22R toyota 1995
@tubejim101
2 жыл бұрын
Only have this one: kzitem.info/news/bejne/zoKOwH-khWp2m4o
@mikeporter7240
5 жыл бұрын
You might as well clean out your injectors and install a new fuel filter.
@tubejim101
5 жыл бұрын
Fuel filter is on my to do list. It seems tricky to get at. Also need to find the local, part numbers for the washers. Keep hoping I can find another engine local, then I can pull parts off it. Would like to get some used fuel injectors and clean them up, then install them on my truck. Trying to keep down time low.
@donnygraves8429
Жыл бұрын
You go that far into it I would just take off the fuel rail and I'm pretty sure your trucks ready for new fuel injectors
@arthurtzouros5622
3 жыл бұрын
What year is this truck?
@tubejim101
3 жыл бұрын
91
@ramonquiroz7153
5 жыл бұрын
4runner ?
@tubejim101
5 жыл бұрын
1991 Pickup DLX
@Caveman1420
Жыл бұрын
Cool I got mine back together with making a video but watch your to make sure my egr valve line was right. How is your motor so clean but inside looks like 500000 miles normally on the outside but inside. Lol
@tubejim101
Жыл бұрын
Had like 350k miles on it when I got it. Did not look well maintained. With a clean engine, it is easier for me to spot problems.
@lauramorales7868
4 жыл бұрын
Buenas tardes a todos, necesito este video tal cual pero en español. Alguien me puede colaborar
@tubejim101
4 жыл бұрын
Click CC, then * select Spanish CC
@shadowXe123
5 жыл бұрын
Good enough for me 👌🏽
@KingKatRider
9 ай бұрын
Screw 22re's, pull that thing and do a swap. My lawn mower has more power than my 22re and I dare to say that its faster too. I hate driving around with my foot to the floor just to try and keep up with traffic. Anyone wanna by a first gen 87 4unner? Need the cash for gas money to start driving my chevy again. lol
@flyprincess69
9 ай бұрын
I had an 86 4Runner in 1993 and I feel your pain. I currently own a 93 pickup and I can cruise 75 easily.
Пікірлер: 71