This cam is made for hydrolic lifters, this means the lobe has a shape to put pre-tension on hydrolic lifters. How is it running on mechenical lifters? Love your build man!!
@WRCgarage
7 ай бұрын
It doesn't matter if we use mechanical of hydraulic lifters, the cam doesn't know that and that's why you need to do the setup for the mechanical lifters to leave a bit distance between lifters shims and camshaft, other than that everyone use them and as long as you do the correct setup it should be fine.
@dieselgate5002
Жыл бұрын
Very good video!! One question, since you had the arp studs, did you have to wear out the camshaft supports?
@WRCgarage
Жыл бұрын
Thanks, no they are all stock the arp's fit just fine. All of the arp kits are made for bolt on, no modifications.
@dieselgate5002
Жыл бұрын
@@WRCgarage Thanks, someone told me that you have to modify them because otherwise they don't fit well.
@WRCgarage
Жыл бұрын
No mate, if you buy them as kit from any website made for 1.9 tdi pd they are all done for bolt on.
@unofficialmusicvideo3441
Жыл бұрын
💪🙏
@dominikkozela9763
Жыл бұрын
Do the pistons have to be machined/clearanced to prevent piston and valve contact?
@WRCgarage
Жыл бұрын
Not necessary, i did it just because i will use nitrous injection and that's a must , otherwise if you stay just with diesel you dont have to.
@yorkshireman7025
9 ай бұрын
With this camshaft do you get lumpy idle when engine is running? I take it the lift is 9.8mm
@WRCgarage
9 ай бұрын
Hello mate, i don't know what means lumpy idle, but i had no problems by now with it, the car is still on rings break in so i don't know yet how will work.
@yorkshireman7025
9 ай бұрын
@@WRCgarage does it sound like mazda rx7 wankel engine at 750rpm 😀👍
@kelekilla
11 ай бұрын
my 1.9 arl engine is stock now ,but im thinking to mounted it because the oem it's dead. will it worth? ...thinking in bigger preparation in a very next future ..or without to go joined to bigger turbo , firad etc it's not gonna work?
@WRCgarage
11 ай бұрын
Anything its good and will improve the power but if you go to far you have to change the internals aswell otherwise will blow up.
@yorkshireman7025
9 ай бұрын
People running 350bhp on stock pistons and rods. How much hp is too much do you think?
@giuffridaelettronica
Жыл бұрын
Measurement of intake and exhaust pads, can you say?
@WRCgarage
Жыл бұрын
I haven't write them down but they are between 2 and 3 mm i think, anyway if you need to do this job just get a set of bigger ones and you will be able to grind them at specified thickness after...
@viktordubnevich9678
7 ай бұрын
Ciao, albero a cam, con cam cosi scuri ? Che marca ??????????!
@WRCgarage
7 ай бұрын
Ciao, its a camshaft from pipercams , nothing to special, just different gradation and valve lift
@viktordubnevich9678
7 ай бұрын
@@WRCgarage E piu resistente rispetto cam di altre marche???
@WRCgarage
7 ай бұрын
I don't know for sure but they are good for tuning !
@viktordubnevich9678
7 ай бұрын
Va bene anche senza mappatura centralina?
@WRCgarage
7 ай бұрын
You have to remap the ecu if you use one of this camshaft as they are different duration and lift .
@elvisvwvw
7 ай бұрын
from what engine were lifters?
@WRCgarage
7 ай бұрын
Don't know exactly i think some ford, JP GROUP 1511400100
@elvisvwvw
7 ай бұрын
@@WRCgarage thanks ... 👍🏻👍🏻👍🏻👍🏻
@petiopetkov8386
10 ай бұрын
Hello, how part number mechanical lifts ?
@WRCgarage
10 ай бұрын
JP group 1511400100
@bradtyson
10 ай бұрын
@WRCgarage How do you get these to work, do you have to use the old lifters and cut them to fit in the top or can you buy lifter heads. The ones I looked at have a hole and recess in the top
@WRCgarage
10 ай бұрын
@bradtyson Check my video with lifters setup, you need to buy new shims for them with the diameter that you have inside the lifters head and thickness about 3mm, then you will have to grind them individually util they reach the clearance you want exactly as you see in my video. If im not wrong, they are 31 mm diameter for your lifters, i let you a ebay link to see what you need www.ebay.co.uk/itm/302508251568?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=9nslwrXiRAS&sssrc=4429486&ssuid=nlA2ZJOUR7m&var=&widget_ver=artemis&media=COPY
@bradtyson
10 ай бұрын
@WRCgarage thank you very much I understand now, what's the best material to use I'm going to buy some 3mmx 31mm rounds and start from there
@WRCgarage
10 ай бұрын
I don't know if they are more types but i think they are all made from a special material.
@flaviumuresan6137
Жыл бұрын
ti-ar fi sarit in cap toti dar aia 90 ii puteai strange fara raportor :)))
@WRCgarage
Жыл бұрын
🤣🤣🤣 Chiar am zis intr-o fraza dar am taiat la editare, e foarte greu sa fac de unul singur si totul perfect si sa mai si filmez totul bine.
@ionutstoican1381
Жыл бұрын
Este același cuplu de strângere si la 1.9 axr?
@WRCgarage
Жыл бұрын
Salut, nu il am manualul de AXR dar toate sunt identice la specificatiile șuruburilor din ce stiu, deci fara probleme cu suruburi noi le poti face exact la fel.
@ionutstoican1381
Жыл бұрын
Ok! Mulțumesc mult! Chiar îmi place ceea ce faci, continuă tot asa cu videoclipurile!
Пікірлер: 42