Please Peter do not play with playback speeds , i like you just the way you are, slow but thorough
@EI6DP
Ай бұрын
yes I found the same
@berndb.5097
Ай бұрын
Da kann ich mich nur anschließen. Diese Geschwindigkeit der "Petersprache" klingt mir zu aufgeregt. Die Leute welchen das alles zu langsam geht sollten sich selbst die Geschwindigkeit höher stellen.
@ny4i
Ай бұрын
I changed the playback to 0.75 so it sounds natural.
@greggabry3128
16 күн бұрын
Thanks peter, always love your videos. This one hit home being an owner of a 705. Pretty cool troubleshooting and props to your skills
@mikefinn2101
Ай бұрын
Peter is amazing and so kind to share such valuable information and teach others. A true Ham and mentor to us all. Thank You so much Peter "The Great" Fixer.
@TRXLab
Ай бұрын
Thank you! That is why we are doing it!
@haramanggapuja
16 күн бұрын
Thanks for the tour. The IC705 is a very complex radio and certainly well above my ability. YOu are lucky to have such steady hands ;-) I was feeling lucky to be able to replace the USB/antenna tuner connector board with the upgraded one. Take care! 73 de W8IJN
@doogsm6013
Ай бұрын
A fault with the first component in the chain! I wish I had that kind of luck! Excellent repair Peter. Not a big fan of these SDR transceivers due to the lack of serviceability. I prefer the old boat anchors ( Kenwoods in my case )and audio equipment for the relative ease of service and parts/donor rigs.
@elcomode
Ай бұрын
For the original voice I switched to 0.75x speed. Thanks for showing the repair. 73's
@lysippus
Ай бұрын
oh, I just saw this comment. i thought it was my youtube settings or something was autotuned!
@elcomode
Ай бұрын
@@lysippus That was also my first thought, because I sometimes watch videos up to 2x speed (e.g. Train cab view).
@coltronex
Ай бұрын
This model is a real pain in the bum,you have a lot of patience,superb instruction!!
@TRXLab
Ай бұрын
Yes agreed.. Thank you
@kennymanchester
Ай бұрын
So good to find another excellent video Peter! As always, textbook methodical process to uncover fault and get a great result. You are a true gem and so valuable for your contributions on proper troubleshooting and repair. I sure wish I could get schematics for all electronics I encounter. It makes me a little jealous. I cannot understand how we have devolved into present day lack of service information for electronics. Anyway, a thousand thank you's for your willingness to share your most valuable time with us. Best 73, NZ5I
@TRXLab
28 күн бұрын
Thank you so much for your feedback!
@richardcook4643
Ай бұрын
Great video Peter, that's way above my ability just getting to the board looks like a pain. Thanks for the video !
@TRXLab
Ай бұрын
Thank you!
@MrKelendros
Ай бұрын
Thx very much Peter for your time. Great weekend with a new great video from you.
@TRXLab
Ай бұрын
Thank you!
@lgroves336
Ай бұрын
Peter CAN fix anything. He is a wizard
@TRXLab
Ай бұрын
Thank you, but not everything...
@tomnorman5461
Ай бұрын
Another fine job Peter, always a pleasure to watch your videos. 👍
@TRXLab
28 күн бұрын
Thank you so much
@chickennugget3362
Ай бұрын
Yay, first! Thanks Peter, Today is a good Saturday!
@TRXLab
Ай бұрын
Thank you :-)
@chickennugget3362
Ай бұрын
@@TRXLab Thank you. Don't leave it so long next time ;)
@AntiqueRadioandTV
Ай бұрын
Peter; Your deductive reasoning and smd soldering skills are impeccable! Looks like we are around the same age. I wish I hands as steady as yours. Fantastic repair, Take care my friend. Tom M.
@TRXLab
28 күн бұрын
Hi my friend, good to see you! Trust you are doing well. Thanks for your feedback. All the best to you and yours! Take care. Peter
@JamesP6084
Ай бұрын
Excellent as always Pete👍
@TRXLab
28 күн бұрын
Thank you so much
@bblod4896
Ай бұрын
Thanks for the Saturday technical class.
@TRXLab
Ай бұрын
Thank you!
@joelkist6493
Ай бұрын
Glade to see you, nice work Mr. Peter!
@TRXLab
Ай бұрын
Thanks
@ouijim
Ай бұрын
Another amazing repair, Thank You.
@TRXLab
Ай бұрын
Thanky you
@ludo9234
Ай бұрын
Excellent detective skills as usual.
@TRXLab
28 күн бұрын
Thank you!
@lylewatts6370
Ай бұрын
Great video and very informative. Professionally done. Thanks for sharing
@TRXLab
Ай бұрын
Thank you!
@skylabby
Ай бұрын
Thanks for taking the time to teach..73
@TRXLab
Ай бұрын
Thank you
@Hank_W6IR
Ай бұрын
You can also see the power out change from 5 watts to 10 at the right side of the PO meter when you switch power to external. Thanks for the look inside. I think this is one radio that if anything dies on me, it will go back to Icom for repair. I did install the USB-C board though but that didn't require complete disassembly.
@TRXLab
Ай бұрын
Yes, true, the power goes up to 10 Watt. ICOM's policy it to swap PCB's only. So be prepared.
@ctid107
Ай бұрын
Nice work. Very compact little radio.
@TRXLab
Ай бұрын
Thanks
@OregonOrcadian
Ай бұрын
Another great video! Thanks. I only wish you had included the hot air soldering work. (Maybe there was not enough room under the microscope?)
@TRXLab
28 күн бұрын
Thank you! In narrow spaces, it is unfortunately difficult to work around the camera..Sorry
@Philg0jba
Ай бұрын
Nice repair Peter. Thank you
@TRXLab
Ай бұрын
Thank you
@iw0hex
Ай бұрын
Good job Peter, nice to see your video, 73 Pasquale IW0HEX
@TRXLab
Ай бұрын
Thanks, Pasquale. Trust you are doing well!
@hamradioop5777
Ай бұрын
I always enjoy your videos, your patience and your skills. Wonderful. Please would you consider showing your desoldering and soldering techniques in the future if possible? 😀
@TRXLab
Ай бұрын
Thank you! Most techniques have already been shown in earlier videos. But hopefully we have some more time in the future to show again all of this stuff..
@aussiedazvk4djh889
Ай бұрын
G'day Peter. I like the replacment board with the USB C connector. Might be something I might look at for my 705. 👍 Great Video.
@TRXLab
Ай бұрын
yes, not bad and very easy to install...
@hancecrawford
Ай бұрын
Hi Peter trust you are keeping well radios seem to be getting smaller nice to see you
@TRXLab
Ай бұрын
Thank you.
@vu3mes
Ай бұрын
This usually happens with the original mini usb connector, I have mine changed to a C type charging port. It works fine.
@notfallmed
Ай бұрын
Hi Peter, danke wieder echt klasse, habe wieder viel neues gelernt ... Grüsse Peter. best 73 😉
@TRXLab
Ай бұрын
Vielen Dank! Das freut mich Grüße 73
@TheGmr140
Ай бұрын
Nice intro for 705😊
@TRXLab
28 күн бұрын
Thank you
@TheCondoInRedondo
29 күн бұрын
Thank you!
@berndb.5097
Ай бұрын
Hallo Peter, gute Arbeit. Hier hört es bei mir auf. Ich bleibe dann besser beim Reparieren von Geräten mit bedrahteden Bauteilen ;-) 73 de Bernd
@TRXLab
Ай бұрын
Hallo Bernd, ja man braucht wirklich die richtigen Werkzeuge insbesondere ein Mikroskop und ein wenig Erfahrung... Danke fürs Vorbeischauen! 73
@michaelclutton8446
Ай бұрын
Thanks for the video Peter de Mike G4VQH
@TRXLab
Ай бұрын
Thank you!
@dl2kck738
Ай бұрын
Hi Peter, I guess that the reason for the filter failure was a bad solder connection of the inductor on that side you have observed the burned pad. I you still have the removed inductor, please measure its resistance. Best Regards vy73, Chris DL2KCK
@TRXLab
Ай бұрын
The inductor was measured fine. The solder joint was burned as seen in the video .
@EI6DP
Ай бұрын
Goo grief Peter that was some challenge to repair the fault. My first thought was a voltage spike which destroyed the filter. What did you find that caused the failure ? Did the OM alter the power out. Jeez looking at the compactness of the circuitry/components it was incredible how you manage that repair. I think I will stick with my Xeigu G-90 🥸 I would not purchase a modern rig at this stage. I believe the manufacturers nowadays are producing equipment which require board replacement instead of board repair. Great job Peter.
@TRXLab
Ай бұрын
Thank you. Most likely we'll never know what caused the fault..It is not that radios like this can't be fixed on component level, it is more that manufactures more and more support PCB swap only. My personal point of view is that it is the wrong way because we all need to be able to afford such a repair...
@extreme978
Ай бұрын
thanks for a good video, keep em coming!
@TRXLab
Ай бұрын
Thanks
@dg3seg
Ай бұрын
Hi Peter, another amazing Video. Tnx 4 that. I am wondering where Do you get those radios 😂. Every Radio has its own special little problem and you fix it. I am very impressed! 73 de Stavi DG3SEG
@TRXLab
19 күн бұрын
Thank you !
@DL5LC
Ай бұрын
Hi Peter. Nice work, but a lot of mechanical work to do, before you can analyse the reason of the error. Thanks a lot for sharing! vy 73, Andreas
@TRXLab
Ай бұрын
Thanks. Yes, agreed it is a lot of work to get everything out, and it is a puzzle to get it back hi hi
@Zeus-ub2zp
Ай бұрын
Hi Peter Please what probe do you use with your spectrum Analyzer to check the power levels in circuit?
@LawpickingLocksmith
Ай бұрын
I bet it either had overvoltage or reverse polarity. Good job!
@TKomoski
Ай бұрын
Wrong the fault was on the radio side of the filter not the supply
@Wendy_Peng
17 күн бұрын
Hello, we are a company that was established in 2003. We mainly sell DC power supplies, AC power supplies, LCR meters, electronic loads, power meters, and other equipment. We often have some defective machines or machines with damaged packaging. The recycling value is extremely high. Are you interested in buying faulty electronics?
@Jimbo10250
Ай бұрын
Great video. I would like to have seen how you soldered that new EMI filter in place with the pads underneath it. Solder paste?
@TRXLab
Ай бұрын
Thanks! No, hand soldering, no solder paste. The filter melts if it gets heat from above. We took it out with hot air, but that was no option for the new filter..
@rlysitt
Ай бұрын
Really nice job
@TRXLab
Ай бұрын
Thank you
@TKomoski
Ай бұрын
As always Peter you make it look easy, I agree with you on what caused the failure. Will you ask the person that owns it if they used excessive power levels? *Cheers* *73*
@TRXLab
Ай бұрын
Thank you!
@sylvainbel
Ай бұрын
Merci pour ce partage
@TRXLab
Ай бұрын
Merci
@davidcottee2808
Ай бұрын
I wonder about the USB connector. If it is able to supply 1A power through the port, then the 3.5A might be exceeded under constant Tx load. Might be even worse for the USB-C connector. And if charging is required as well with a flat battery. The filter might be under specified. Maybe the 7A version should have been used. Most likely though Icom have thought about this, and the current supply is limited through the USB port.
@TRXLab
28 күн бұрын
The USB connector is NOT used to supply the radio..
@davidcottee2808
28 күн бұрын
@@TRXLabBut it IS used to supply power to a connected device. Or is that function disabled?
@theheathkitshop2424
Ай бұрын
Peter, how long did it take to work down to the board with the fault?
@TRXLab
Ай бұрын
If you are trained it takes only a couple of minutes, but if not it may happen that you give up.
@jontze
Ай бұрын
Thanks Peter. So the lifespan of an IC-705 is as long as there are batteries. Or you have have to fix the issue...
@TRXLab
Ай бұрын
lol obviously yes
@AG8000
Ай бұрын
Gute Arbeit 👍
@TRXLab
Ай бұрын
Herzlichen Dank!
@borjaruiz1941
Ай бұрын
Hi Peter, great job with that EMI filter soldering. Did you check the service menu to see if someone was messing with the power settings?
@TRXLab
Ай бұрын
Thank you. Setting was finde...
@reginaldriley904
25 күн бұрын
Hi Peter my name is Reggie and I would like to know if you can do the TX mod on my icom 705 and is there any other way to get in touch with you. Thanks Reggie
@esbenarndt5703
Ай бұрын
could you short leg 3 and 4 on the emi? wouldn’t that show if the filter is the only fault?
@TRXLab
28 күн бұрын
Yes, possible as long you make sure that there is no short behind the filter
@dl7majstefan753
Ай бұрын
Murphy: The probability of a faulty component is inverse to it´s accessibilty!
@TRXLab
Ай бұрын
That's true
@transmaster
Ай бұрын
continuous FT-8 for hour after hour, after hour?
@de_w8tam
Ай бұрын
I've run my ic-705 pretty hard on ft8/ft4 without a problem. I suspect it may have been a faulty component.
@TRXLab
Ай бұрын
Not only FT8 there must have been another factor too...
@willietorres283
Ай бұрын
Enjoyed the video . Can you tell me how you got started in repairs and what books you used ?
@TRXLab
Ай бұрын
Oh boy that is a long story..but to make a long story short after college a lot of different positions in big companies and collected experience over the decades..
@jamesgeorge1709
Ай бұрын
How can Icom call a 20watt rig QRP? I have a 703 and would not trade it for a 705..😊
@TRXLab
28 күн бұрын
It is a 5 Watt QRP radio with the internal batteries attached. If you put an external supply to the radio, it delivers 10W..
@jamesgeorge1709
28 күн бұрын
@@TRXLab doesn't day that in the
@jamesgeorge1709
28 күн бұрын
@@TRXLab advertising doesn't say that
@dbailey3024
Ай бұрын
Could you please tell me where the USB c board came from? Dylan
@de_w8tam
Ай бұрын
If you search for 'Icom IC-705 USB-C/SEND Control Board Upgrade' the first link that comes up is the source. It's pretty easy to find. I have one in my ic-705 and it works great. It also provides a higher current buffer for switching an external PA. 73
@dbailey3024
Ай бұрын
Thankyou for the link and I love your videos the way you explain things is just exquisite and is so helpful so for that thankyou
@angelomarcone8221
Ай бұрын
A very interesting video. Amazing job. Thank you. 73 de ik8vrq
Пікірлер: 122