Thank you for the info you provided, very nice and helpful 👍🇲🇾 12:15
@paulcook8316
Жыл бұрын
Thanks for the share.i 've been thinking of doing a 32p swap,pretty much straight forward.thanks again.(2wd strc lcg slash/rustler pro-trac 4kv HW)
@MrRui33333
Жыл бұрын
good project and mods !!! i like models traxxas 2wd ,.. so fun,.. sorry my ingles !
@VikingDudee
3 жыл бұрын
I got me a 3674 hobbystar motor I was planning on installing into my slash just to get rid of the heat issue with the VXL system, I just never got around to it
@joshjohnson9167
4 жыл бұрын
I just upgrade my sons bigfoot to 32 pitch and and I know what you seem as far as it seeming "smoother". His is running the blx100 motor/esc 17/54 and its impossibly fast on 3s. GPS at 44 on 2s and wheelies a anything over 52 kn 3s
@scottfirman
Жыл бұрын
I have the Bandit and changed the motor over to brushless. I noticed the gearing still prevents the Bandit from reaching a high speed top end. I think I will change both the Spur gear and Pinion gear. The new ESC is fan cooled, so I don't need to worry about over heating issues like the brushed motor would experience. Good video by the way.
@jorgeguillen6806
Жыл бұрын
I’m having over heating problems I have a 3300 motor and 18/86 gearing and my battery dies quickly
@scottfirman
Жыл бұрын
@@jorgeguillen6806 Dial it back. You can only go so far concerning hopping these things up. Time to move up to a better classed RC.
@rcn4fun012
4 жыл бұрын
I'm in the process of doing the monster conversion. I didnt know about the 48 to 32 conversion until now. Very nice video Have you tried any other pinions?
@mathias4891
3 жыл бұрын
Always use the esc to fix cw versus ccw . Sensored motors wont like the phase wires being reversed.
@stuwest3653
Жыл бұрын
It's clearly not a sensored motor.
@albertrivera8776
3 жыл бұрын
Great video brother ! I have a question can I do the same but still use my velinuem 3s vxl motor ?
@lbrcguy
3 жыл бұрын
Thanks! Yes, but you will need to look for 3mm shaft 32 pitch pinions.
@Miguel_289
4 жыл бұрын
Great video real informative. Gonna try using a 48p pinion with a 5mm bore from hot racing need the gear cover to bash :)
@lbrcguy
4 жыл бұрын
I've had this set up for a couple of months now and I flipped, rolled, and tumbled many times with no damage to the gears without the cover.
@itzpotater8418
3 жыл бұрын
you can modify the gear cover btw my friend
@theshyguitarist
Жыл бұрын
Was watching another youtuber and when he did the 32 pitch upgrade, he put the cover right back on...I think his Slash 2wd was a newer model. Don't know if that makes a difference.
@RCRoads
Жыл бұрын
Great job with your upgrade. I have no idea but does a 32p gear hold up better than a 48p? The reason I ask is because I'm having issues with 2 of my cars destroying spur gears.
@stuwest3653
Жыл бұрын
32p is stronger but you are most likely having another issue with your gear mesh.
@RCRoads
Жыл бұрын
@@stuwest3653 I have been setting mesh with 1 sheet of note book paper for 48p. Maybe there is a better way. My BigFoot and DR-10 are both running 48p plastic and being pushed by Spectrum BLX100 (same as it the Typhon and Granite) . Continuously stripping spurs on both cars. I'm running the exact same motor and ESC in my 1/10 scale Sunfire on 32p metal gears and they don't strip out. The car is lighter and runs smaller tires. I think it could be that with large paddles on the DR-10 and the quick take offs in sand is too much for the spur. The BigFoot actually had a problem that I just noticed. I put different shock on it and there was too much travel causing the sliders to drag on the suspension arms.
@jasonphillips4229
4 жыл бұрын
What CVs are on it?MIP?I'm putting castle creations 3800 kv 5mm shaft in my stampede so I'm looking for gears
@lbrcguy
4 жыл бұрын
Yup...MIP's. Put then on when I broke my first axel.
@RayRiv73
Жыл бұрын
Hpw is that motor holding up....looking to buy one for my Fiesta Rally
@gamercat7004
Жыл бұрын
Do 32p gearing drain the battery faster?
@joejoefasho4267
4 жыл бұрын
Where do you drive it? How do you keep it so clean?
@lbrcguy
4 жыл бұрын
Mainly at the park. I avoid water if possible. I do enjoy cleaning all my trucks... simple green, brush, water hose rinse, air compressor, wd40, air compressor again!
@digeolrc8586
Жыл бұрын
What did you feel after changed pitch 48 to 32m on rc?
@rcn4fun012
4 жыл бұрын
Which traxxas vehicle's use the 32 pinion, I'd like to see they gear ratio chart
@davide.2851
4 жыл бұрын
I believe that 32p gears are standard on the VXL Slash and Rustler 4x4.
@annmatiskam4571
3 жыл бұрын
32 pitch or pinion. They aint the same
@MartinP0815
3 жыл бұрын
Basically all of them (ok I dont have an XMAX^^) My Slash 4x4, 2wd, bandit and ERevo are all using the exact same spur gear^^
@annmatiskam4571
3 жыл бұрын
Can you put the same pitch on a brushed bandit
@MartinP0815
3 жыл бұрын
Yes, you can even still use the cover with some spacers. But I dont see the need for it. The main improvement is the 3665 Motor and they come with 5mm shafts so no 48P pinions for them^^
@firemyster4707
3 жыл бұрын
Is that an upgrade? Your just increasing the acceleration but lowering the speed.
@splooof
3 жыл бұрын
thats not how it works
@el_tanke_grande2458
3 жыл бұрын
Can you send me the links to the spur and pinion gear I wanna upgrade mine
Пікірлер: 43