I love my x& Pro and it is all I can do to maintain control and not pull the trigger on the x30 with the e85 extension kit until I see some real world reviews like this.
@TheClackShack
Жыл бұрын
I will be getting lots of use out of it. I have 2 orders of 160 each coming up soon.
@tazman622
Жыл бұрын
I've picked up the xTool 40 Watt 'upgrade'. I have not had time to set it up on my extended 20w unit though. I'm dying to try it because at 40 watts 1/2" is possible from what I have been told and seen. I'm not working 1/2" materials a lot, but can't ever have enough power! Here's hoping Clack Shack can do a review soon as well.
@TheClackShack
Жыл бұрын
I haven't tried the 40 watt but it 1/2 inch can be cut with multiple passes on some of my other machines.
@ericeinsmann5559
Жыл бұрын
@10:02 it's nice that the shield is removable. I don't think I would ever keep mine on.. I am waiting on my Comgrow 20watt laser but I don't think it's shield is removable. I do have an idea of marking the sides with a sharpie right where the laser should be located. I think this will give me a better idea of where the laser will burn when I frame it in lightburn
@TheClackShack
Жыл бұрын
On the Comgrow, the shield isn't removable, you can take the glass out but it is still very hard to see.
@Samotnick1
Жыл бұрын
I placed an order two days later I got an email that they were out of stock. They offered a more expensive version because as they wrote these are available. I agreed and placed a new order after they returned the money. Two days later I got an email saying that this one is also out of stock! This company is a scam.
@TheClackShack
Жыл бұрын
It may be that they are seriously out of stock. I have dealt with Atomstack before and they are a real company. They were doing a pretty heavy advertising campaign and could have sold all of the stock.
@rohithrao9050
3 ай бұрын
Hi Thank you for detailed video, Can you plz suggest best engraver and cutting for beginners, which one to buy , criyality, sculptfun , or atomstack ?
@TheClackShack
3 ай бұрын
That depends on intended use, needs, size requirements and budget. I have many reviews on good machines but each has different strong points
@stormtaker63
Жыл бұрын
I've always wondered if the Adamstack and the Atzer were made by the same company.
@TheClackShack
Жыл бұрын
They are very similar...
@bazookaproof2
Жыл бұрын
Atezr 35 vs the Atomstack A30 need a head to head video.
@TheClackShack
Жыл бұрын
If I can get my hands on one... there is a rumor I may.
@jackhelm9852
Жыл бұрын
Other than the head power, it looks like exactly the same setup as my A20. Question. Is the USB connection in the control box solid or does it wiggle around when plugged in? Mine really has a ton of play which has always bothered me. And I SO VERY MUCH agree with your assessment about where the cables come out. WHY does it have to come out the top? I wonder if the Module will work with my A20 setup since they look so similar?
@TheClackShack
Жыл бұрын
It does look very similar but I cannot say if the modules would work or not.
@louvp57
Жыл бұрын
I enjoy your watching your videos, I have An Atomsack A5 and have the same complaint about the USB cable sticking up. I purchased a right angled USB cable so it doen't stick up it lays flat.
@TheClackShack
Жыл бұрын
I guess that is an option. I managed to route them better on my new base and it is tolerable.
@dangerous8333
Жыл бұрын
Ahhhhh....NOT the Falcon 2 33 watt like a suspected. 😂 👍
@TheClackShack
Жыл бұрын
No, I would love to try out the new 33 falcon but haven't yet.
@patriklindgren8063
Жыл бұрын
How is the detail on the 33watt? The stronger laser has a little larger laserspotsize (0.08x0.1mm compared to 24w that has 0.06x0.08mm) Is it still smal enough or do you miss out on detail becaus of this?
@TheClackShack
Жыл бұрын
It is not very noticeable compared to most 20 watt machines.
@justinmcclung
Жыл бұрын
Random question but I think you can help. I use Lightburn and have dealt with an issue since day one. Recently I got an Atomstack A30 Pro and the same problem exists so I figured I would dig a little deeper. The issue is when I go to frame anything, the laser head moves just a bit then the whole thing just locks up until I power it down. Is there any way you could share screenshots of your lightburn settings for this A30 Pro? Settings, machine settings & device settings perhaps? Thanks for your help and keep the great videos coming!
@TheClackShack
Жыл бұрын
I haven’t had any issues, you can send them to my Facebook page
@qapla
Жыл бұрын
Maybe by the time I can get a laser they will be up to 100 watt and priced down to $500
@TheClackShack
Жыл бұрын
Looks like it wont be long.. lol
@qapla
Жыл бұрын
@@TheClackShack Wish someone would send me a laser engraver
@Repent1133
Жыл бұрын
I have the X30 Pro where did you go to change the speed from 6000 to 18000? I have the same issues when I do burn tests. I know I am not getting the most efficient use out of the laser right now. Thank you 🙏
@TheClackShack
Жыл бұрын
Machine settings… it’s a controller settings
@DjBillyT
Жыл бұрын
@@TheClackShack I am also looking for this setting and struggling to see it in Machine settings I am sure I am missing something but I definitely do not see max speed settings in machine settings
@carolwolfe757
Жыл бұрын
How do you focus the laser with the shield off? I just bought this laser.
@TheClackShack
Жыл бұрын
Using the tool that comes with the machine. One way is shield, other is no shield. Sticker on the tool explains
@carolwolfe757
Жыл бұрын
@@TheClackShack Thank you! My laser comes tomorrow!
Пікірлер: 35