I've watched maybe 10 of these videos and none of this made any sense to me until I watched this one. Now I understand it perfectly. Thank you.
@BrandonSolid
Жыл бұрын
Hands down the best detailed video on how to use a timing light for initial timing and total timing advance. Thank you.
@Myvintageiron7512
Жыл бұрын
Glad it was helpful!
@marcusupshaw829
Жыл бұрын
Wow! Vintage Iron is back!! Love the hell out of this mans content. It seemed like it went away for a while. I’ll be watching if he keeps publishing
@ComicalCowboy1911
Жыл бұрын
Very nice video for the use of timing lights! Only thing I’d suggest is the mention of disconnecting vacuum advance (for those who are using it) and plugging the carb and distributor before measuring total timing, or mechanical advance with the light. Some newbies forget this step. Of course it’s not applicable if someone is running only mechanical advance but I wouldn’t suspect many newbies would.
@bubba_hunts
27 күн бұрын
Honestly, I'm glad you commented because I knew about the vacuum line but I had to learn what mechanical advance was because my 350 has it
@kevinw6282
Жыл бұрын
great explanation, and nice use of props ;) Appreciate your taking the time to explain things, folks can certainly learn a lot!
@Myvintageiron7512
Жыл бұрын
Glad you enjoyed it!
@ToddDunning
Жыл бұрын
After dozens of KZitems this is the one that made sense. Thank you sir. Very interesting point about chamber size.
@brentrogers8558
Жыл бұрын
Thanks so much for the videos. For a guy like me starting his very first complete engine build, your content is awesome!
@yaqoubalmounes434
Жыл бұрын
Very good explanation. I watched several videos about this topic but couldn’t understand how it works. Now I got it.👏👏
@flyinhighaerial3193
Жыл бұрын
Thank you, You just explained a advance gun operation better then anything on the net. Now I can use to set timing on my 69 Beaumont.
@javidrumrodriguez2788
Жыл бұрын
I watched alot of your stuff or my first small block block. Your voice brings back the old days
@moparnut6286
Жыл бұрын
This use to be easy cause most of us timed our own engines.... But with modern cars timing is now computer controlled and most people can't understand the concept of engine timing and turning a dizzy or advancing/retarding a cam or chain.... You've explained it very well now no one has any excuse not too know how to time a classic!😁👍
@tinkertime614
Жыл бұрын
Great video found this very helpful and you covered all parts!
@blackbuttecruizr
Жыл бұрын
Super insightful! Wonderful to see more content from you.
@Myvintageiron7512
Жыл бұрын
Glad you enjoyed it!
@cdpperformance2613
Жыл бұрын
Great to see you back thanks for all the great info!!
@Myvintageiron7512
Жыл бұрын
Thanks for watching!
@LJK69187
4 ай бұрын
Always the best videos!!! Very helpful!!!
@brianmaynard7320
Жыл бұрын
Good to see you, Vintage!! Loving the videos! Thanks for sticking around!!
@Myvintageiron7512
Жыл бұрын
You bet!
@richd5749
Жыл бұрын
Thanks and Happy New Years, I follow you almost perfectly. When u state 6 degrees and show it from where you're at, it might b a bit more visually friendly to bring in the camera shot, maybe if possible walk slowly into a closeup shot, this is what the home shop was all about in the 50s, 60s. 70s, when we can fix what we manufactured here at home in the States. I have a 37. & 1948 Dodge Coupe w/ 218.7, homeland fuel resources are being threatened as well as the Classic Dodge and others. Just saying. Thanks again for your time and effort to teach us, so focus up folks!
@rogerowens5669
Жыл бұрын
Good job it'd be nice if you would take them from start to finish on break in with a flat tappet cam!" You seem to have a natural knack for teaching and this would be great for your beginners👍 I'm assuming that's the design of your sight I live in a totally different world with dual dual mags 😉👍 once again great job and I do appreciate your sight very much👍
@Myvintageiron7512
Жыл бұрын
Yea Dual Mag's are definitely a different world high end drag racing I have run magnetos on a few street cars you got to be careful with the amperage it can be lethal
@Wrenchen-with-Darren
Жыл бұрын
Nice, video. Thanks for taking the time to make it.👍
@thadrepairsitall1278
Жыл бұрын
Excellent description. I learned a bit even though I'm a mechanic. I deal with newer vehicles.
@Myvintageiron7512
Жыл бұрын
Great to hear!
@arizonanumbersstation1727
11 ай бұрын
Another great video--thank you.
@raypulliamelectronics8312
Жыл бұрын
Your very good at what you do, I really appreciate it. God Bless
@Myvintageiron7512
Жыл бұрын
I appreciate that
@brandonmena3873
Жыл бұрын
Awesome vid. Really appreciated. Thanks
@billyhead1625
8 ай бұрын
Nice video well presented, Thank you Sir!
@manuelpolitis7123
7 ай бұрын
Really good explanation- thanks
@chuckg9805
Жыл бұрын
Great video. I always wanted to see how those fancy timing lights worked. My 50 something year old craftsman ain't got that! Thanks
@Myvintageiron7512
Жыл бұрын
Yea the older ones with no degree meter are really only effective for bone stock engines with a big cam Initial Timing means nothing it can vary greatly depending on cam grind
@Rob_Diamond
3 ай бұрын
Very helpful. Thanks!
@ronbunker5778
Жыл бұрын
Good explanation, it helped me a ton!
@Myvintageiron7512
Жыл бұрын
Glad it helped!
@MrAnimalsrtasty1
Жыл бұрын
Great explanation!
@justinsmith847
Жыл бұрын
Wow I really appreciate this video thanks
@patrickarce5481
4 ай бұрын
Really helpful this video thanks
@ibrahim-chevelleMalibuman
Жыл бұрын
This video helped me out a lot very nice awesome thanks for the great video’s of all time ❤❤❤
@Myvintageiron7512
Жыл бұрын
Glad it was helpful
@barnbuiltdiesel4036
Жыл бұрын
Great video very informative
@Myvintageiron7512
Жыл бұрын
THX
@ssboot5663
Жыл бұрын
Thanks for the video..... My timing light doesn't have the adjustment to pick the degrees.We always timed at low speed with vacuum disconnected and low rpm to achieve timing B.TDC>.. I have always wondered how your kind of lights work to compensate to proper degree setting at TDC. on our Snowmobile engines back in the day we timed them at 6000 RPMS. Thanks again!.
@rksg2003
Жыл бұрын
Camera did a decent job of showing timing light if you ask me. Good video
@woden79
Жыл бұрын
Great explanation! Thanks
@Myvintageiron7512
Жыл бұрын
Glad it was helpful!
@TheFrameoff
Жыл бұрын
Great vid , well explained Build On
@Myvintageiron7512
Жыл бұрын
Glad you enjoyed it
@BarrelMH
Жыл бұрын
awesome video!!
@Myvintageiron7512
Жыл бұрын
Thanks!
@1965escamilla
6 ай бұрын
Best video
@danielesilvaggi
Жыл бұрын
Thank you very well described.
@Myvintageiron7512
Жыл бұрын
Glad it helped
@robertmills3682
Жыл бұрын
You are the first person to explain this and it make sense to me, thank you! You didn’t mention anything about connecting or disconnecting vacuum advance. If vacuum advance is disconnected like they suggest you do, how is that considered showing total timing? Because when you connect the vacuum back up and rev the engine then it’s going to advance further, correct?
@richd5749
Жыл бұрын
Flathead Terry in Canada and on utube does a good instruction.
@dblr616
Жыл бұрын
Engines loose vacuum when the throttle is open so vacuum advance has nothing to do with total timing it’s more for light load and starting purposes I set mine at 32 total and leave the vacuum disconnected and they are 10:5:1 or 12:5:1 mildly built for circle track racing and they start fine and don’t kill starters some guys run fully locked distributors and say 32 is 32 when setting timing, but them guys generally spin the engine first then add ignition otherwise it bucks the starter hardcore not ideal for daily drivers obviously
@Myvintageiron7512
Жыл бұрын
Vac advance only effects timing slightly above idle it has no effect on total by the time you get to 1500 to 1800 rpm your Vac advance is done it will affect timing at low rpm but honestly, I never worry about initial timing only total, I do recommend disconnecting and blocking it when checking timing
@joe-hp4nk
Жыл бұрын
After that you have to experiment with the rpm total timing comes in, that means picking the right springs for the weights in your distributor. For me it's around 2500rpm at about 34 to 38 degrees on my SBCs, it depends on your combination.
@shootermcgavin2819
Жыл бұрын
great video, very informative
@Myvintageiron7512
Жыл бұрын
Glad you think so!
@shootermcgavin2819
Жыл бұрын
@@Myvintageiron7512 What brand of timing light do you recommend?
@garythorsell5061
Жыл бұрын
Nice video 📹
@nursecuenca
10 ай бұрын
Great video. What should full manifold vaccum be on 350 sbc?
@chasmontecarlo7271
Жыл бұрын
Very good video I will be starting my 72 montecarlo it has a 350 stroke to 388 will the timing have to be set up differently. I’m self taught on cars I would appreciate any input information thank you very good video 👍
@Ricky-mouser
Жыл бұрын
Centrifugal, or mechanical advance is a speed sensing device, vacuum advance is a load sensing device. The ladder allows one to run more advance on light load for better fuel economy
@theedge8659
Жыл бұрын
Dude do a video on retrofit roller cams and old block versus the TBI block roller cam buttons springs you need how to put LS springs on a vortec but offset keepers because we only got a small party information about roller cams from you thank you sir
@earth2steven197
Жыл бұрын
Can you use timing tape on the harmonic dampner with a non dial back timing light to get the same result?
@greatwhite8571
9 ай бұрын
Question so I need to have the balancer mark lined up with 10 degrees before tdc when I put the distributor in the block correct?
@chasepyles8626
7 ай бұрын
Are you unplugging the vacuum advance on the distributor when getting initial timing and plugging it back in for your total timing?
@MRtucnakCZE
Жыл бұрын
If only you have released this video 6 months ago. Neverthanless, I did manage to set the correct timing with OBD EFI with the notches on the flywheel/timing marks. It is important to make the engine, if it's a EFI, go into a service mode, where all the timing controlled by the computer is turned off. I couldn't manage to rev it up, since the engine automatically goes out of the service mode, but I did set it up as what the manual calls for. Had it waay too much advanced. It just feels like it's a bit sluggish now and gulps a bit more of a fuel. Any ideas as to why?
@fukemallgarage
Жыл бұрын
Great stuff, as always. Weird question, I'm sure you saw blasphemi go lean and break the motor at drag week. Could you do a short video about the science behind how lean causes catastrophic failure. Your the man. Thanks
@Myvintageiron7512
Жыл бұрын
Great suggestion! The short answer is Gasoline cools the cylinder by absorbing heat when the cylinder goes lean its way to much air (air can also be considered a fuel for ignition) and not enough fuel to absorb heat much like an Acetylene torch when you add Oxygen the flame gets so hot it turns blue, this is what happens in a lean cylinder the temps get so high they melt stuff but that is only part of the problem this also causes pre ignition IE: Ignition of the fuel before the spark plug fires the piston has to push up through the burning fuel (Extreme Pressure) for an extended number of crank degrees this can hammer a piston and rings to death very quickly
@fukemallgarage
Жыл бұрын
@Myvintageiron7512 thanks for a great explanation ... you thought you were done teaching lol. Thank you for what you do
@nursecuenca
11 ай бұрын
What temp thermostat do you recommend for 350 small block chevy? I currently have no thermostat and truck runs at 165-185 degrees. Or should I leave it as is? I enjoy watching and learning from your videos. Keep up the great work.
@bonethrower1957
7 күн бұрын
Ok what happens to the total advance when you hook back up your hose to the distributor. It's going g to move the advance higher than 30 right
@RememberanceChirori-ri9hi
7 ай бұрын
Well explained
@DarthMayers
10 ай бұрын
Hi I wanted ask if I have 10 initial timing and I want 34 total . I rev engine 3000rpm do I set my timing light at 34 or at 24? Was confused on this part
@nursecuenca
Жыл бұрын
Just subscribed. Great detail video. I have 350 chevy small block. On my advanced setting set to 30 at 2,800 rpm I get timming to 0. But now I notice a clunking sound from exhaust. Any suggestions? I'm new to car scene and I'm learning about car. My c10 truck has Edelbrock carburetor 1407 1498. Thanks
@user-xk2np8sd6o
2 ай бұрын
Off subject . I have a 300 hp 327 small journal. I was told all small journal have forged cranks. To build a 7000 rpm engine I was told I only need Forged pistons and better rods and the 2 bolt with factory crank is good up to about 500hp. Is that accurate Info?
@nursecuenca
Жыл бұрын
I live in Southern California. What fuel should I use for 350 chevy small block engine?
@MichaelJohnson-cm4wp
13 күн бұрын
When you had the timing light at 0, you had 6 degrees BTDC on the damper..When you add 30 to the timing light that moved the mark way down..As the engine revs to make the mark move up to zero, wouldn't that be a total of 36 degrees? Or maybe 24 degrees if I am looking at it backwards..?? I would set the engine at 0 advance(runs like terrible), set the timing light to zero and then you advance the distributor to 6..I am just wondering if it is 36 or 24 or it is correct the way you did it..
@davidharris8861
Жыл бұрын
Just make sure that with number one cylinder at top dead center, the timing mark is at zero before doing anything else first. Over the years, I have run into a few harmonic balancers that had spun slightly on the rubber lining!!!
@reddbulll7644
Жыл бұрын
Thanks for the info, that motor sounds like it has a cam upgrade does that change anything on how u time ur engine?
@Myvintageiron7512
Жыл бұрын
Total timing is what you go by with a bigger cam
@Chasemanuti
4 ай бұрын
What if your timing chain cover is not matching the balancer marks?
@tomthatcher3444
11 ай бұрын
Great video, thanks
@jayambry510
Жыл бұрын
I’d really like to see a detailed video discussing how ignition timing works. For example, what static timing is versus mechanical/centrifugal versus vacuum. Also, how to adjust total timing and know that your okay with where the initial timing ends up. Curve kits, etc.
@FirieonOG
Жыл бұрын
? The distributor is a static timed piece ; with vacuum modulation it just advances the timing based on the less vacuum applied to the distributor
@trickster8635
Жыл бұрын
That was the point of the video, dude.
@kylesweeney5647
8 ай бұрын
Check out Uncle Tony's Garage timing vids
@shaflower3183
Жыл бұрын
The engine, a 4-cylinder 22RE, on my 89 Toyota pickup got wet, and I had to change the airflow sensor. Although doing that got the truck going again, I might have thrown the timing out while trying to fix it because the idle is still very rough. Can I make the timing better from just adjusting the position of the distributer without necessarily using a timing gun? Another thing is that I think there's too much grease build up on the timing cover and balancer to see a degree setting, or does the gun somehow let you see what's needed even if there's grease buildup covering that area? Thanks.
@Myvintageiron7512
Жыл бұрын
I would not mess with timing without a light you could cause engine damage if it's advanced to far why do you think the timing changed? did you move the distributor?
@nursecuenca
Жыл бұрын
I have small chevy 350 with mild cam. I tune engine to advance 35 at 3000 rpm tdc. On idle its running 12 degrees before tdc. When using vacuum meter to adjust my edelbrock carburetor the best number I could get it was 14. Truck sounds good but would I cause a problem with the engine? I have not check the springs inside carburetor. Would you please offer any suggestions I would appreciate.
@Myvintageiron7512
Жыл бұрын
Don't worry about where timing is at idle, set total at 3K where you wany it and send it
@mjtii9177
6 күн бұрын
Great content can you make a vid on a reverse rotation engine
@juniorwhelchel6337
Жыл бұрын
I race dirt circle track here in South Carolina we have to run completely stock motors in your opinion what is the best timing degree for performance on a stock 350
@Myvintageiron7512
Жыл бұрын
That depends on your fuel you want to advance it as far as possible without pinging (detonation) the best power I have seen is 36 degrees for a SBC with flat piston and closed chamber head but that was with good gas our fuel these days isn't that good if you're running totally stock you have dished pistons and an open chamber head 7.9 to 1 compression IE: lower compression this will allow more timing with low grade fuel you kind of need to play with it to find the sweet spot 87 octane probably won't like much more than 33-34 degrees with your low compression you could probably get away with 36 and premium fuel but is also depends on you altitude and humidity levels they have a pretty dramatic effect on timing as well
@nursecuenca
Жыл бұрын
Do I start with advance settings 1st or do I start with tdc at zero settings 1st. I'm new to car scene. Great video. Just subscribed
@Myvintageiron7512
Жыл бұрын
I would go right to total you don't worry about timing at idle set total at 3K RPM and where ever initial ends up that's where it stays it will usually be 8 to 10 degrees
@rustybritches6747
Жыл бұрын
Can you use a dial back timing light with an MSD ignition to set Total timing MSD says you can't use a dial back light to set the timing but I think the multiple spark stops at higher rpm? I built a pretty nice little Ford 302 with full roller valve train aluminum heads mild cam and I'm running about 16 degree initial and all in about 3000 rpm for a total of 37 degrees I think but again Im using an MSD 6al box so I'm just not sure if that's too much or if its even correct! I have the same timing light as you also!
@aaronlogan7084
Жыл бұрын
I built a 350. Put it on a run stand it fired right up and ran it for about 35 min for cam break in. Timing was set perfectly and ran awesome. Too engine and put it back in my k10 truck put distributer back in and put carb back on and now I cannot get the timing right. It will not start at 0 degrees. It seems to run at 30 to 35 degrees. I checked for vacuumed leaks and everything. I'm not sure where to go from here.
@dblr616
Жыл бұрын
Make sure you put the wires back on where you had them if you didn’t pull the distributor, it should not have changed…I’ve seen bad engine grounds on a run stand cause some odd issues so maybe give the block a ground in the truck just use jumper cables for testing going back to the wires most people think they need them in a specific place I mean technically you can throw the distributor in where ever get it in then drop it in the oil pump roll the engine over until the #1 is on tdc then wher the rotor lines up set #1 to the prong on the cap that’s just before it and wire it from there 18436572 boom you got a runner I usually set it to the second prong past the coil/ ignition wires on the cap then vac advance don’t usually get in the way when timing it.
@jasonfenn3391
Жыл бұрын
That's not quite how I understand it to work. So correct me if I'm wrong.. I own a 1995 gmc Sierra k2500 4x4 with the 5.7/350. And on the decal it says the timing for that engine is "0" degrees..so I set my timing light for "0" degrees and and unplugged my brown wire for the computer started the truck up and rotated the distributor till my timing marks lined up at "0" degrees. I tightened the distributor shut the engine off and plugged the brown wire back in and started the truck back up . I don't remember exactly what the advanced timing was somewhere between 15 I think and 20 advanced but I could be wrong about that .. but the engine does run excellent. It's not hard to start at all. Turn the key and starts instantly. So would that be correct ???
@Myvintageiron7512
Жыл бұрын
You are comparing a computer-controlled ignition (TBI) to an HEI and a carb, it's apples and oranges, in your case the timing is advanced by the computer so 0 is the baseline and the CPU takes over and does the rest without a computer (Carb and HEI) setting at 0 will not work
@michaelbelknap2923
Жыл бұрын
What balancer did you use ? Part number? I am building a sbc and want the full timing scale on the balancer. Thanks 😊
@ChauncyFatsack
Жыл бұрын
Summit sells balance stickers that wrap around the whole thing and ive seen better more visible ones then that just Google them
@Myvintageiron7512
Жыл бұрын
Professional products part # 80000 www.summitracing.com/parts/pfs-80000
@michaelbelknap2923
Жыл бұрын
@@Myvintageiron7512 Thanks
@dtruth5769
Жыл бұрын
At what rpm should engine be at when timing it? Also should vac advance be disconnected when setting initial timing?
@dblr616
Жыл бұрын
Usually they stop advancing somewhere between 3 and 4K. You basically rev it up til it stops moving set it to your desired overall and lock the distributor down, there’s only one setting. if you set your overall to 32 then your base timing is what it is if you set your base timing to say 6 degrees with vac. advance unhooked it’s gonna advance to whatever the distributor advances to from there which may be higher than a desired of say 32 so I think that’s why he’s sharing the video because you don’t wanna set your base at 12 and be 45 overall on a higher compression engine because it will destroy itself so important to check overall, ideally dyno session with carb and timing adjustments to find out your happy place but even a blind squirrel finds a nut from my experience you build a little domer 355 or 383 it’s gonna live at 32 degrees total timing
@Myvintageiron7512
Жыл бұрын
for total timing you will be all in around 3000 to 3500 depending on ignition system and engine and yes with engine at idle disconnect the vac advance and plug the hose sorry I forgot to mention that in the video
@jerbear6947
Жыл бұрын
@@Myvintageiron7512 Hi, hey so why again do we need to remove the vacuum advance hose and test it out of normal functioning condition? Being that when it is actually running regularly it is with vacuum advance hose on ???
@davidwarland2680
Жыл бұрын
Gday from OZ, mate watch n love your stuff, very well worded and so easy to understand. Got a question on timing, rebui8lty an engine, 4cl toy, over double the horspower of stock, no dyno for a thousand miles, so, have been told big webers, go direct to 38 degrees total timing, which is what i have, but ? no knocking that i can hear, so, add some more, take some out, leave it therte ?| 10.5-1 instead of 8.5-1, cnc worked head, twin dcoe webers, custom one of cam, med 6al-2 ignition system. custum headers to 2 1/4 exhaust How do you calculate correct timing when u leave stock behind ?
@Myvintageiron7512
Жыл бұрын
I advance 2 degrees at a time until I start to hear ping under part load the back it off until it goes away
@davidwarland2680
Жыл бұрын
@@Myvintageiron7512 sweet, thank you, is what we did in the 70s, lovely to see some things stay the same.
@BOWGUY3015
Жыл бұрын
What model timing light? I have a dial from hobo freight and I hate it.
@Myvintageiron7512
Жыл бұрын
I bought it at AutoZone it's not top of the line, but it does work well I also have Snap-On Light, but I didn't want to use that for this video it might scare people off not wanting to spend the money I think I paid about $80.00 for the one in the video the Snap-On light is $350.00 the AutoZone brand works just as good I compared the timing of this one with the expensive timing gun from Snap-On they read exactly the same so you don't need the high priced light
@joe-hp4nk
Жыл бұрын
The first thing you have to do is make sure the TDC of #1 piston and the 0 mark on the balancer match.
@bobdimartino6738
Жыл бұрын
i thought you disconnect vacuum to the distributer to set timing
@danielmoreno3122
Жыл бұрын
Does the engine have to be at operating temperature??
@Myvintageiron7512
Жыл бұрын
it should be
@trickster8635
Жыл бұрын
Not every mechanic makes a good teacher.
@jimmyjimbo61
Жыл бұрын
Just trying to learn... so, my distributor has 24 degrees of total advance built into it at 3,000 rpm on a machine. So... to get it to 34 degrees total timing at 3,000 rpm, I need to basically retard (after top dead center or 0 degrees) the timing 10 degrees after while idling. That way, as the advance comes in, it will come back to the zero mark on the pointer at 3,000 rpm. Is that correct for the initial timing?
@Myvintageiron7512
Жыл бұрын
10 degrees before not after
@TheTopCat650
Жыл бұрын
💕💜💕💜💕💜💕💜💕
@joe-hp4nk
Жыл бұрын
The next thing you do is rev the engine up until the timing stops advancing and dial the timing light back to 0 to find the total advance the engine is at.
@joe-hp4nk
Жыл бұрын
If you need more or less, you can play with the initial up to a point. If you need more, the football in the distributor needs to be changed.
@cjwelty2012
Жыл бұрын
Just to check? If you started with 6 degrees. And you 30 total. Wouldn’t you want it to say 6 degrees when you rev it up. Because the light is not getting the signal until 6 degrees
@Myvintageiron7512
Жыл бұрын
no with the light set at 0 you want to see 6
@coarsegrind
Жыл бұрын
Not all engines are timed to the number 1 cylinder. International Harvester 304 engine uses the number 8 cylinder.
@Ricky-mouser
Жыл бұрын
On a sbc, I sometimes use 6 and split the difference. I bet on your 304 you can use its running mate as well
@ehguy3628
Жыл бұрын
8:55 don't you mean that you have built 30 degrees of delay into the timing light? Not 30 degrees of advance.
@user-bw5nc
4 ай бұрын
Couldn't you just keep the revs up, then set it at zero?
@rogerpatton-zr7qd
6 ай бұрын
Ibeleave that tech mark is two degrees
@tombentson9693
Жыл бұрын
Nice vid, but didn't show how you came to get to 34 degrees without going over
@Myvintageiron7512
Жыл бұрын
The timing light is set for 34 when you Rev it up and the timing advances just make sure your mark is on zero it’s actually 34 degrees because that is what you have set your light for basically your retarding your light 34 degrees so when it advances to zero your actually at 34
@johnstonis7977
Жыл бұрын
Or you need a Progression Distributor.😉
@tombentson9693
Жыл бұрын
Or when tim8ng starts to come in and whu
@lincolnstovall9471
Жыл бұрын
Degree with that, LOL.👍🤙👍🤙
@SPEEDYBEANIE22
Жыл бұрын
Just learned how to use a VACCUM gage and now I’m learning this
Пікірлер: 147