Way more aesthetically looking than most DIY vacuum casters
@shokoladkas
2 жыл бұрын
Wow Dima, this is amazing and inspiring. Talented people are talented in many things :). Excited to see what will you make next!
@noviceartisan
2 жыл бұрын
Hahaha, I ended up doing mine using the lathe... Mounted a drill bit in the chuck and pushed the chamber against the bit by hand till it was done. Might not be perfectly centre, but it worked. Drill presses be tiny when you add on the size vice you need to hold big stuff!
@wasiza6475
5 ай бұрын
Great work man
@laikadefcon8817
Жыл бұрын
Тоже хочу такие инструменты :') Спасибо за видео!
@joshuablanchette2836
2 жыл бұрын
Where did you get the acrylic cylinder from? Can you post link please?
@DmitriIvanov
2 жыл бұрын
I'm in Germany, i got it from this shop here: www.plattenzuschnitt24.de/Plexiglas-Rohr-Zuschnitt/
@yakfish36
2 жыл бұрын
Fantastic job mate seriously good vac caster. Thanks for this.
@phillybpy
5 ай бұрын
How much would you charge to make me one. I don’t have all the equipment you have
@admincvpag7120
Жыл бұрын
any possibility to post dimensions? hard to guess
@NeoQJ
2 жыл бұрын
Did the plexiglass tube still hold up now?
@DmitriIvanov
2 жыл бұрын
Yes, I've used it a bunch to degas epoxy and cast things since I've built it, no problem yet.
@thybigballs
Жыл бұрын
I had to look up the strength of plexiglass. It may be better than a glass dome. This was something I found while searching: "Looking at the load-bearing capacity of acrylic, we can state that the weight required to break an acrylic sheet is about 30 times greater than a glass pane of the same thickness. Suppose a pane of glass 1 metre wide and 3 millimetres thick breaks at a weight of 1 kilo, then a three-millimetre thick acrylic sheet will break at a weight of 30 kilos. That is quite a difference. This is also the reason why acrylic is widely used in load-bearing and heavily loaded structures, such as showcases and aquariums."
@FatKidBrody
Жыл бұрын
A little coolant goes a long way.
@_S_Y.007
29 күн бұрын
Как же это приятно когда человек работает, больше чем разговаривает хотя-бы в половину..... Тебе моё почтение,лайк и подписка!!!!! Вас таких мало!!!!
@dutchdb
Жыл бұрын
"Don't judge me." I can commiserate with this every time I do a thing.
@alliswell8149
7 ай бұрын
Which rate
@paulmanhart4481
Жыл бұрын
Very good work. I won’t say anything about your hand drilling though. Been there too many times. It would have been nice if you had given more explanations about the various steps. What 3D printer do you use? I noticed Formlabs on the screen but wasn’t sure if that was the printing material or printed. Formlabs has some investment casting PLA from what I hear. Expensive equipment though. Thanks, Paul
@octapc
Жыл бұрын
Is it a good idea to degass before pouring plaster and then again in the cast in case the cast has bubble traps?
@florencelibellule7224
2 жыл бұрын
Impressive! Well done!!
@pastapasta3012
Жыл бұрын
Could you specify the dimensions of the material? Pipe diameter and thickness, lid thickness. Thanks.
@DmitriIvanov
Жыл бұрын
5mm wall thickness pipe, lid and bottom is also 5mm. The Plexiglas is 10mm. Diameter is around 150mm.
Пікірлер: 24