30:48 One thing I forgot to mention the retraction settings I mention apply to Bowden tubes. If you have a direct drive you want to test at a 1mm or less or you’ll have some problems.
@NorwegianWeirdo
Жыл бұрын
Hi, is it the "Retraction Distance" that should be less than 1mm? I've had some stringing issues as a ender 3 S1 Pro user. Also thank you for this excellent video.. I definitely saved this profile. Edit: Welp.. something is wrong with the settings. After finishing the initial skirt, the whole printer restarts and I get an "unexpectedly stopped files" message. kzitem.info/news/bejne/mI55tpydsoioapg It only happens when using the settings from this video, any of the default settings works fine.
@spawncalibur1022
11 ай бұрын
@@NorwegianWeirdo curious of what to set. The minimum distance is 10.0mm with the yellow error thing(not red). my retraction distance I have at 0.6. Yet to test
@johnx9318
Жыл бұрын
This is the second of your videos I have watched. After three years of fiddling with Flashprint, PLA and my adventurer 3, and a further two weeks of sheer frustration with trying to use ABS and PETG - I have finally made the move to Cura. So far, I have invested two hours in your videos. Great information and presented perfectly - THANK YOU!!!
@stanstocker8858
Жыл бұрын
You've nailed one of the biggest things for getting good surfaces by telling people to slow down. Three klipper machines here, all tuned, one Marlin machine that hasn't been klipperized yet, and a VMinion also fully tuned for resonance and linear advance. My default print speed range is 35 to 50 mm/sec on all of them when I intend to paint the model. Actually the VMinion can do quite well at 80, but there is a bit of improvement by dropping into the 40 to 60 range. Sort of a gut feel based on the model more than some exact rule. A vaguely boat like blob in 8 minutes isn't something of much use in my little world. You're doing some very interesting and well thought out videos here, thanks!
@ItsMeaDMaDe
Жыл бұрын
Well thank you for your comment. I’ve put a lot of time and thought in my stuff to make it easy to understand and help everyone. Your one of the few I’ve found on my side when it comes to speed. How quick people for get about the tortious and the hair…😄 Thanks again.
@GreySectoid
Жыл бұрын
You can also adjust the wall print speed even lower, that way it doesn't slow down the print time too much because most of the time it's printing inner walls and infil.
@MTRUITT95
7 ай бұрын
One of the best KZitem videos ever! I am a BBQ, Laser Printer and more recently 3D wannabe. I am going to say it, Best Vid Ever! Well done!
@kyleshafer5403
2 ай бұрын
Had so many issues with bed adhesion and I was always having to print on a raft, didn’t even think of first layer speed ! Works sooooo much better and I’m actually saving time and materials!! Thank you, you got a new follower!
@bubbadoolittle2812
Жыл бұрын
Best 3d video on KZitem! Keep posting! You just answered about 90% of the questions I have about 3d printing!
@Frightline777
11 ай бұрын
WOW! Your videos really make a huge difference and your logic is sound!! Because of the videos, i have improved my prints and trimmed the time off substantially.Keep them coming..i will keep watching.You are one of the best teachers i have seen.Thank you
@bjornml.08
7 ай бұрын
I've seen 2 of your videos on Cura and just want to thank you so much! You expain things so well and thoroughly, step by step. Makes it easy to understand and apply.
@RuthRivera-f6k
5 ай бұрын
Thank you so much for these amazing videos. I have had my ender for a year now and gave up on it. until I came across one of your videos and then went on to watch many more. My prints are perfect, smooth and my main thing was warping. Raft has saved my prints. Thank you
@dougbas3980
Жыл бұрын
Learned a lot! Especially about analyzing the slices in Cura to avoid time intensive fails. Great advise!
@ItsMeaDMaDe
Жыл бұрын
That’s awesome glad I could help. Analyzing prints is something most don’t do but it can save time and filament!
@michaelgueble6789
Ай бұрын
@ItsMeaDMaDe Good morning. There are plenty of tutorial videos on You Tube. Particularly in French, my native language. I'm new to 3D printing. I use cura and fusion 360. It's really not easy to find videos as well explained as this one. You really go in depth and explain the interactions between such and such settings really well. And despite the fact that it is in English, your video is truly a blessing for me.
@Cferg
Жыл бұрын
Thank you! I’ve been printing almost 2 months now. Today I learned about infill and ironing.
@ItsMeaDMaDe
Жыл бұрын
Wonderful! Those are definitely two important settings. You should be checking and understanding best of luck with your future Printing!
@Clownmeati8
4 ай бұрын
Thank you for all the great info, I just started 3d printing a couple months ago and you and a couple others have been a real blessing.. I bought a budget printer, (anycubic kobra 2 neo) and it has been awesome. The slicer is perfectly fine for most of what i do.. Mostly parts and hardware without tons of detail but I have reached the point that i think more options becoming important now and likely more important as I run into problems I'll need to find a fix for. Im still a little too new to really know what i need yet but im taking your opinion and tryng cura . looking forward to outgrowing my printer and uphrading but i cant say enough about how impressed i am with anycubic so far. Ive been cnc woodworking for about 10 years and now and was intimidated by 3d cad but got lucky choosing onshape to learn on. (Lucky because I went there because it was free) Six weeks later at the youtube university I'm designing and making my own stuff, couldnt have done it without help like yours, so thanks again! Also thanks for saying oriented instead of orientated! 😊
@jasonb-sk4px
3 ай бұрын
this video changed everything i know or knew about 3d printing. thank you for this video
@ItsMeaDMaDe
3 ай бұрын
Wow! Well I’m glad I could help!
@SabMega
Жыл бұрын
I really enjoy how you actually explain what things are your an amazing teacher thank you for your time.
@michaelaxmann7245
8 ай бұрын
Your tutorials are top notch and entertaining. Ever thought of a live stream for beginners to show their problems/fault for you to give troubleshooting advice?
@DennisCrawfordJr
Жыл бұрын
i thought you talked about adaptive layer height in a video but I couldn't find it quickly. guess ill start watching them all again. there has lots of good info. i have done about 5 busts since watching this video and they look so good now. thanks
@ItsMeaDMaDe
Жыл бұрын
Im so glad your prints are turning out great! I actually don’t talk about adaptive layer height. There is a lot to it and the video was long enough 😅. I was thinking I might do another separate video just talking about that in the future.
@DennisCrawfordJr
Жыл бұрын
@@ItsMeaDMaDe cool, I just found out that it messes with your supports. It makes them go at weird angles and not work as good.
@RobOnekea
Жыл бұрын
CHRIS!!! These videos are awesome! Watched two of them already and my prints already improved. Can you pleeeeeeze do one on supports?? That would be mucho appreciated!! Great job!
@ItsMeaDMaDe
Жыл бұрын
ROB!!! Glad you like them and I’m glad your seeing good results. I’m planning on a support video in the near future.
@rachaelb9164
3 ай бұрын
Rafts are awesome for print in place as well. It avoids that elephant foot squish deformity on the bottom layer that makes it hard for stuff to move freely. This is great info. I’ll go a couple months without printing then I forget what settings to use. I have an older Anycubic but I’ve been having issues with external dimensions and pieces not fitting together properly. I think I just need to tweak some stuff and save as its own profile.
@computergururick
3 ай бұрын
Fantastic video. Helps a lot. I am printing with ASA and this has helped greatly. Thanks.
@DennisCrawfordJr
Жыл бұрын
Thanks. When I use lighting I always clicking from the nozzle dragging or hitting the infill.
@ItsMeaDMaDe
Жыл бұрын
Let me do a short explaining what you could do to fix this.
@nelsongonzalez6292
Жыл бұрын
THANK YOU hello from Colombia the best 3d teacher
@mariedst-louis1459
9 ай бұрын
You’re really good at teaching ! such a nice and good video :) thanks !
@dmonhuntr75
Жыл бұрын
Excellent video. This is very helpful, I wish I had this info when I started printing.
@laich2
Жыл бұрын
very detailed tutorial. thank you so much
@ItsMeaDMaDe
Жыл бұрын
Glad it was helpful! But to be honest this is nothing compared to what I’m putting out in the next few weeks starting tomorrow. I’m going over everything Cura has. If you want detailed don’t miss this series. 🤓
@DennisCrawfordJr
Жыл бұрын
Thanks!
@ItsMeaDMaDe
Жыл бұрын
Thank you so much Dennis!! I really appreciate the support!
@kenspaceman3938
Жыл бұрын
Another very informative video, thanks!
@ItsMeaDMaDe
Жыл бұрын
Glad you liked it!
@grahamwood3105
Жыл бұрын
thanks very much for your video help . i am going to try this.
@ItsMeaDMaDe
Жыл бұрын
Great glad I could help!
@AjeethCheppudira
Жыл бұрын
Great video with excellent tips.
@debrasam5525
Жыл бұрын
I have binge watched your channel since finding it a few days ago. Why do you tun your prints perpendicular? Is there a reason?
@ItsMeaDMaDe
Жыл бұрын
That’s awesome this is my favorite comment today! Just doing my part to feed the addictions of the hobby. I do that cause I’ve found I get less fails. Don’t have any data but it seems to just work better.
@debrasam5525
Жыл бұрын
@@ItsMeaDMaDe sometimes experience over data gets the best result in life. Thanks for the response.
@georgespapillon364
10 ай бұрын
Hi ! I do not have that title bar on top where you choose the printer, material...! I use Cura 5.4
@MrRayGooh
Жыл бұрын
Thanks for all the info.
@apryllsadventures7520
8 ай бұрын
can you make a beginners tutorial for tevo tornado 3d printer?
@cyranodaburgerack8745
Жыл бұрын
I'm printing a Prusacaster (guitar) and the core piece has 7 walls and 25% infill to prevent warping because of strings temsion. On that topic, I printed a remix of the pickguard which has a raised hexagones logo and the lettering "Prusacaster". When I use 0.2 layer height it completely ignores the logo and the lettering. Then I tried 0.12 layer height and turning on "print thin walls" and it worked! Except I don't know which of these two changes made it work. Any idea? Very informative video as always!
@ItsMeaDMaDe
Жыл бұрын
That’s cool. On the topic of your question I would say it’s layer height. The quality naturally gets better the thinner the layers. That’s my best guess.
@goatelope7539
8 ай бұрын
This is fantastic. Thank you
@andrewmortimer3317
Жыл бұрын
Such a good video! This has a huge number of tips I will keep referencing as I keep printing going forward. The info you shared about wall settings for nice models and overhangs will be a big help on some current problems I’ve been working through. Keep up the great videos!
@ItsMeaDMaDe
Жыл бұрын
Glad it was helpful!
@hectorpalacio6131
2 ай бұрын
I have a Flsun v400 3d printer set up the same way the settings would be about the same
@angeladorno2150
Жыл бұрын
I like you tutorials, but I have never get a good set up with yours settings.
@WhereNerdyisCool
Жыл бұрын
I'm confused, in your video about travel settings, you discussed not using Retract at Layer Change?
@NearlyHatedForLife
2 ай бұрын
I love this video ❤
@evosithlaw
6 ай бұрын
Hi, I'm just getting stated in Cura, and it's connected to my Snapmaker J1s and Snapmaker 2.0 A350T 3 in 1 Dule Extrusion printer. How can I import my print settings from one PC to another, or where do I find that file? I don't know where it's stored.
@ksmillar69
Жыл бұрын
Why can't I see the Nozzle Drop down when in "Prepare"? I only see an option to see "Material"
@ItsMeaDMaDe
Жыл бұрын
I’m not aware of this feature in Cura.
@ReelSpider
2 ай бұрын
Is there a way to change my location and dimensions to millimeters instead of meters? Everyone is telling me I can, but not one person can tell me how. I'm from the U.S., metric is not my system, and with my old eyes and tired brain, I can't count the zeros anymore...
@richardsimmons6470
Жыл бұрын
Little confused about changing Permanent settings ie Those that will refer to EVERY setting on a particular Printer ie saving the results of these tests If so what should the order be of each setting Are changes saved automatically or should they be changed into a Profile which would then be updated each time I presume you would be running on that profile for everyday printing Special settings would be saved into that Model ie if you wanted a special pillar type A lot of problems are caused by insufficent instructions from manufacturers like setting up the build plate (Auto Level machines) initially AnyCubic has a Level Template Creality you adjust the wheels initially and then ise auto levelling
@caintforcookie1018
Жыл бұрын
Hello. Thanks so much for your tutorials. I am about a year into my 3D printing journey and I mainly print cookie cutters. Biggest headache is stringing. Could my filament brand be the issue? I’ve tried changing settings and retraction towers with no luck
@ItsMeaDMaDe
Жыл бұрын
Hey! I have found some filaments are more prone to stringing it also depends on the printer. The filament could also have moisture in it as well there are multiple factors but changing to another brand to test is a good start.
@caintforcookie1018
Жыл бұрын
Thank you. I'm on a ender 3 v2 BTW.
@botondbalazs4893
2 ай бұрын
Hey im begging you to show me how to ajust my bedsize , because i have a anycubic kobra 2 max and my bedsize is 42mm x 42 mm but my cura is showing a much much more smaller bedsize .
@rodgertaylor3204
Жыл бұрын
Hi Chris, been going through your videos for the umpteenth time lol. Was just wondering when in your quality setting you the layer height at. 0.1mm and initial layer height at 0.2( 0.4 nozzle). Do you level the bed to 0.1 or 0.2, I have a feeler gauge. Thanks for all the good work you are doing for the 3d printer community. Thanks for any help. 🍺🍺
@ItsMeaDMaDe
Жыл бұрын
So I typically will have a first layer of .2mm and I will level my bed to a .1mm height. This ensures I get a good squish on the build plate. So you would use a 0.1mm feeler gauge.
@rodgertaylor3204
Жыл бұрын
Thankyou.
@sanjivk
Жыл бұрын
Need some help.I made a Stl file with certain dimensions. however when I load the file into Cura and scale the dimensions all change. How do I tackle this
@wilsonrivera1156
5 ай бұрын
I have a Qidi tech shadow 6.0 pro3d printer and new to add this can I do the same thing as the kingroon 3d printer or should I stay with just the kingpin 3d printer also I lost the Zip drive that came with it how do I replace it or do I just download it. PLEASE HELP !!!
@alexandermoon4031
Жыл бұрын
Is there any way that you can share or talk about how you get the G code to actually have Cura run the machine if it's connected to a computer?
@ItsMeaDMaDe
Жыл бұрын
I could add that to the list for a future video.
@drewd6083
11 ай бұрын
Can we get your profile you created in this video?
@Bart_Depestele
Жыл бұрын
Hi Chris, thank you
@ItsMeaDMaDe
Жыл бұрын
You are very welcome
@dakupenndragon810
Жыл бұрын
Love the videos on Cura man. I just got a question, will changing speeds and stuff in Cura effect Klipper speeds? I just preordered the Elegoo Neptune 4 Pro which has Klipper built into it, my current printer the Shark v3 doesn't have that. I'm just curious because I have never messed with a machine with Klipper.
@MMQsTacosConLimons
Жыл бұрын
How can we add your profile into cura?
@Oldmanflyfishing
10 ай бұрын
Sometimes you just have to tell Cura, “ Wasup”? Classic
@ultrabob32
Жыл бұрын
Hi, thanks for the videos, very helpful, i have a problem with my filament flatten out to the point of jamming, any ideas to look for rather then turning of retracting
@kevinwithrow
11 ай бұрын
Extruder is too tight had that issue last night
@BB-kz9cb
Жыл бұрын
How does this model print without supports?!
@johnx9318
Жыл бұрын
We can't go on meeting like this...
@TrasherBiner
11 ай бұрын
The 1930's cartoon villain moustache is too distracting...
@TheRamenGhost
8 ай бұрын
Lol 😅 I love his mustache
@AP-yd1wz
10 ай бұрын
Dude looks like he 3d printed his mustache. Good content though. 👍
@cyates42
Жыл бұрын
Thanks!
@ItsMeaDMaDe
Жыл бұрын
Thanks so much I really appreciate it and I’m super glad I could help you!
@TheExtremeElementz
Жыл бұрын
Where is it!? I want to see the Hulk print! Haha 😂😭😅 But seriously this is helpful print gold right here thank you. 🙏🏽
@ItsMeaDMaDe
Жыл бұрын
Ha. I was waiting for someone to say that 🤣😂
@frankieventura9923
Жыл бұрын
Aloha I know you mentioned on here that these settings are for ender3, would it work on cr10 with a 0.6 nozzle?
@ItsMeaDMaDe
Жыл бұрын
So I have a CR-10 and these settings work for it too. But. I haven’t used a .6mm nozzle with it. I would have to do some tests to find out.
@wolfman75
Жыл бұрын
Thanks Chris!!! Very Helpful!!!! 👊👍😎
@ItsMeaDMaDe
Жыл бұрын
Great to hear!
@jimmenet7956
3 күн бұрын
Would these settings apply to a larger nozzle size such as a 6 ? I have some glow in the dark glitter I want to a quality model with.
@Jaguet
7 ай бұрын
Just wow! It was the best video ive ever watched about cura settings, Thanks!
@MadMackz
8 ай бұрын
YOU DONT ACCELERATION OR JERK ADJUST??/!!!! BRO,,,,,,BRO0..... I highly suggest trying out all accelerations set to 500, Jerks at 20, initial layer jerk/layer print jerk 8, in layer travel jerk 5. skirt brim jerrk 8. You will cut hours off your prints without quality loss. try it dude . its worth it. (And I also swear by the 15-20 mm adhesion layers but I use a cht hoternd so i crank the speed to 60 due to the extra flow ive gained with the cht nozzle (also highly recommend a CHT)
@meyou9369
7 ай бұрын
I really like how you go by each setting and explain it in a way that you understand what it is doing and why. Normally, people just gloss over settings like this and act like it's already clear enough. The use of examples and scenarios is great.
@TasosX
7 ай бұрын
What a wonderful channel, very helpful, whenever you find time, could you please make a video with the best settings in Ultimaker Cura for 3d printing miniature wheels for rc drift cars? 30mm x11mm.
@PeterAgostiniJdcap26
10 ай бұрын
You know guy your videos are good but way too long ya my loss … get to the point . Ty
@amused2deth
Жыл бұрын
Bless you brother! Great video!!
@ItsMeaDMaDe
Жыл бұрын
Thanks I’m glad you liked it.
@amused2deth
Жыл бұрын
@@ItsMeaDMaDe LOVED it!
@BB-kz9cb
Жыл бұрын
Is there a way to import settings profiles? for example I have an Anycubic Kobra Max. Could I download like a fine detail profile for doing busts or figures?
@ConnersWorld
Жыл бұрын
Finally! Someone with a Cura video explaining this process like I'm 5 years old! Hella yeah, bless you brotha! So ready to begin my printing journey!
@ItsMeaDMaDe
Жыл бұрын
I tried to make it for any skill level even the level of I have a box with a 3D printer in it now what?! Be sure to check out the rest of the series I break down Cura and how to use it. Best of luck and happy printing
@juliofranco9244
11 ай бұрын
Hello sir I buy a creality 3v2 neo but I can print nothing it just spaghetti salad can you help me please thanks
@MorrWorm8
Жыл бұрын
Bro I’m struggling. I’m going to go through every second of this. I have a old Anet A8
@DennisCrawfordJr
Жыл бұрын
Do you have a must do list for when you get a new filament. Like, temp tower, retraction tower, flow calibration and so on
@ItsMeaDMaDe
Жыл бұрын
I’ll make you another shirt to answer this. Let’s see if I can answer it in 60 seconds 😅
@ItsMeaDMaDe
Жыл бұрын
Here is your answer! kzitem.infoVyunhZ6LEEA?feature=share
@EngMakerBr
11 ай бұрын
Thanks!
@ItsMeaDMaDe
11 ай бұрын
Hey!!! THANK YOU! Thanks so much for the super thanks and supporting my channel. I really appreciate it!
@WarrenPenner
Жыл бұрын
Pure gold right here! Thanks again!
@ItsMeaDMaDe
Жыл бұрын
No problem glad to help!
@hdyeahh
Ай бұрын
great video ! thanks !
@ritesha8050
10 ай бұрын
i print my first layers at 5mm/s🤣
@dianabarron6447
Ай бұрын
Do you share the profiles you create?
@cyates42
Жыл бұрын
I’m a newbie 😂 but these videos make me a pro. Appreciate you my man… GREAT VIDEO AND KEEP THEM COMING
@ItsMeaDMaDe
Жыл бұрын
That’s amazing. Super happy to hear that. Thanks for the comment.
@richardsimmons6470
Жыл бұрын
Can you save "Your Settings"
@omidesmaeili
Ай бұрын
one of the best tutorials ❤👌
@hendrikjbboss9973
Жыл бұрын
Hi there Chris, fantastic presentation as always 👏🏻 👍🏻 Remember that I asked about nozzle size in a previous video? Well, watching this video I realized that while Cura 5.3.0 does provide different nozzle sizes for Creality Ender 3 Pro it does not provide any other sizes than 0.4mm for Ender 3 S1 Pro. This is a problem for me as it forces me to use Cura 5.2.2 or PrusaSlicer 2.6. 😮
@ItsMeaDMaDe
Жыл бұрын
Thanks! Very strange. You can’t change it in the top panel of the screen? I’ve never heard of anyone not being able to change it…
@hendrikjbboss9973
Жыл бұрын
@@ItsMeaDMaDe There is always a "first time" for everything 😛
@prateekbajpai2291
6 ай бұрын
waiting for supports
@andyb7754
Жыл бұрын
Excellent informational video, as always! Thank you.
@ItsMeaDMaDe
Жыл бұрын
Glad it was helpful!
@SUVwanderer
Жыл бұрын
Fantastic video! Really well done, it was a huge help.
@ItsMeaDMaDe
Жыл бұрын
That’s great I’m really glad to hear it!
@franzgriffle6063
11 ай бұрын
Nice!
@TheAgyemangDuah
Жыл бұрын
Thank you for these tutorials, they are really helpful. I can't help but wonder the amount of tinkering you did to achieve all these helpful tips
@vfpfineart
Жыл бұрын
what was the settings for print in place models? Ty for such detailed instructions 🙂
@dcchillin4687
Жыл бұрын
New to printing, thanks for the cura rundowns!
@christian_U81
Жыл бұрын
Takk!
@ItsMeaDMaDe
Жыл бұрын
No Thank you so much. I’m glad this could help you!!
@jesseburson
Жыл бұрын
I print slow too. Mostly of the time I don't go more than 40mm/s. When you print for quantity, you lose that quality.
Пікірлер: 139