You do have to spend some time setting the saw up... blade, fence, etc. But once done, the saw is great. Fairly compact which is Nice kzitem.infoUgkxXh-4_3-ZT1fFWP91ZV7iVqzElr0lEb-a I did get an Incra Miter Gauge which takes some setup as well. The stock miter gauge can be adjusted in the miter slot with a little painter's tape... this tightens up the side to side play a lot.
@DPShopTalk
8 жыл бұрын
I just added a note in the video about not making the saw cabinet air tight. You need to make sure you leave enough openings in the saw to feed the air flow of the dust collector. The key is to control and concentrate the air flow, not block it off completely. I should have clarified that in the video. A member of the BeThePro forum brought that to my attention that I didn't specify that in the video so I wanted to put that out there.
@craigburghardt8604
3 жыл бұрын
I want the gaps to be around where the dust is being created. A vacuum is litterly an absence of air, basically making the saw cavity a vacuum is my thinking. If the shop vac is working too hard when I hook it up, I will add some holes around the saw plate. That is the point of mess creation. I have watched so many of these videos my head was spinning. So now when I am faced with actually setting something up. When that happens I go to big picture. My general thinking is directed wind tunnels. In miniature where the dust is being created . . . in the shop in general, moving in clean air in and moving unhealthy air out. Filtered if possible on it' s way out. I have some experiments to run. Perhaps I will film and post on my other channel. My mind has some ideas that have stumped the internet. Also, I firmly think the end point of any DRS should be outside.
@gruebane
7 жыл бұрын
That back piece is WAY more elegant than the contraption I almost started ... I just completed a cardboard template for my unit ... very happy!
@hammockmonk
8 жыл бұрын
Great tips, thanks! I especially like the magnet solution on the panels.
@killawee118
7 ай бұрын
That overhead is great. I’m surprised more people haven’t built the same…. This version is great and this is 7 years ago.
@QUARTERSAWN
3 жыл бұрын
I just acquired an older Delta contractor saw, and this is exactly what I needed. Thanks for the post and also the template for the back!
@akquicksilver
7 жыл бұрын
Very clever enclosure around the motor and belt.
@randybarton7712
3 жыл бұрын
Good job. Good, practical information for the average guy. And bonus points for having no obnoxious music.
@gregboutelle3902
8 жыл бұрын
Definitely interested in seeing how you made the overarm collection! Nice video!
@stephenwiseman3264
7 жыл бұрын
Liked the earth magnet idea to seal up back of saw.
@mikeash7428
7 жыл бұрын
Nice dust collector adaptations. Very slick design with the puzzle pieces and magnets. I was wondering how to enclose around my outside motor. Also like the fellow who used cardboard templates to make puzzle pieces to patch together before cutting out his real estate sign boards. Love this sharing of great ideas. Thanks. I'd like to see your demo of the overhead blade dust collector if you can fit it in. Would be much appreciated.
@dougnath2772
8 жыл бұрын
Would love to see the arm build!!
@JT_70
7 жыл бұрын
Your mdf panel by the motor looks superb and gave me an idea. I made a cardboard template then used the template to make the interlocking panels for my old Craftsman using leftover political yard signs. These were the corrugated plastic signs. By cutting out the panels with an Exacto knife, the two panel pieces nested perfectly inside each other with no gaps or spaces. It's then easy to cut holes thru only one side of the panels and insert the magnets. Spray paint will cover all the politics. You can also buy corrugated plastic or PVC boards from craft stores and big box stores if you can't find any political signs or real estate signs. I was originally going to use mdf or hdf but this was so much easier and quicker.
@DPShopTalk
7 жыл бұрын
+John Temple great tip, thanks for sharing! Good to see election signs being put to good use for a change :) If you would like to have your setup featured on the Viewer Projects page you can submit some photos and a description to have it added in. www.danpattison.com/blog/viewerprojects
@bobkucheran1950
5 жыл бұрын
I would very much appreciate seeing how you put all this together!
@DPShopTalk
5 жыл бұрын
You can find the link for the overarm video in the video description.
@hannatree478
4 жыл бұрын
I have an ancient Triton sawbench. It's a good old Aussie but a little less sophisticated compared with modern saws. However, I'm a diehard and will make do in the extreme if only to spend days solving all the problems. , after all it does the job it's intended to do. So first I learned to sew badly and made a haute couture bag with a funnel that hung into a bucket underneath. Daggy but it worked fine except for the dust.Today that's a relic of the past having seen this video. Thank goodness for genius far in advance of mine!. Since the bag, I've also added a lovely little windy uppy thingummywhatsit to raise the blade and lower it, oh what a joy!! it even has a brass doorknob for a handle. Well the bag isnt going to de derigueur anymore, so your ideas will certainly be adapted to my situation which is pretty much dust coming from everywhere, including out west and down south of here somewhere beyond the recently blackened stump. Thanks.
@user-mp4me9jm5u
Ай бұрын
I would definitely like to see how the overhead desk collecter arm over the blade is built.
@pperly
3 жыл бұрын
Excellent ideas. Especially liked the idea of the magnets and the soft foam for stuffing in the misc. gaps. Well done.
@edweberjr.3800
6 жыл бұрын
Yes, I would love to see the support system made. Very interesting project, thanks for the idea video.
@DPShopTalk
6 жыл бұрын
Heres the overarm video: kzitem.info/news/bejne/uXyvrZyrbWWliIo
@acerjuglans383
5 жыл бұрын
That back panel is the solution I needed. Thanks.
@stephencosbey7106
Жыл бұрын
Dan, Thanks so much for this presentation. I closed up my old delta table saw as you demonstrated. Of course all saws are different so there was much trial and error (heavy on the errors). However after getting the plywood in place and closing up the cracks and crevices with aluminum HVAC tape, I cannot believe how well it works. I just finished dadoing a couple of drawers with 1/2 and 1/2 joints and there is no dust to speak of. Incredible.
@paddlepower888
4 жыл бұрын
Embedding rare earth magnets to the back panels: drill a hole the size of the magnet, tape one side, insert the magnet and tape the other side. Cardboard is lighter, cheap and allows for smaller magnets. Thanks, Dan!
@user-xu7yq1ud2z
2 жыл бұрын
Dear owner of the channel, I wanted to tell you about my admiration for you and your channel and for my benefit from your experience and style. My heartfelt greetings.. Ali - Saudi Arabia
@rodj9902
3 жыл бұрын
Very nice build, the magnets on those rear panels, genius ! :)
@DPShopTalk
8 жыл бұрын
Be sure to share some tips on table saw dust collection that you've found helpful. What do you use on your saw? Let's get some discussion going and see what has worked for others.
@Dennis-kj9qx
4 жыл бұрын
Much better than the cardboard cut outs and duct tape I've been using... Starting this tonight ! Thanx D
@christinecahill2874
7 жыл бұрын
hi, my first time on your channel and i have to tell you that it was extremely helpful. im headed out to my shop to close up the opening on my 10" tablesaw ( craftsman ) love the idea with the magnets, im not so thrilled on trying to figure out that jigsaw puzzle though. lol i do appreciate you posting. very helpful to me and my lungs. thanks again bud.
@DPShopTalk
7 жыл бұрын
+Christine Cahill glad to hear you found it helpful. It takes a little bit of fiddling around to get a template figured out but it's not too bad.
@paddlepower888
4 жыл бұрын
I revisited this clip and shared to a grateful friend. Immense improvement. Next: Topside collection! Thanks.
@bigthinkinguy
7 жыл бұрын
Thank you for the excellent video. I'm very impressed by your idea for closing off the back to improve collection efficiency.
@rla1000
Жыл бұрын
3:40 To seal the gaps under the cast iron table, I used a can of that spray foam insulation (the non-expanding version). It was a bit messy so anyone wanting to try it, take your time. A little at a time works better. I think by masking it would be easier to apply. Narrow slits I caulked with clear adhesive caulk. For small openings (btw, I have a Delta full cabinet saw), I used small pieces of clear packing tape. For the blade tilt hole or other large openings, you can buy rubberized magnetic sheets that you are likely familiar with in the form of refrigerator magnets with ads on them. I bought a five pack of 12" x 12" sheets and cut to fit as needed. Undoubtedly other sizes are available. This would seal better than the spongy foam. I like your over-table arm and I'll likely build something similar to fit, although I want the ability to move it or swing it out of the way when not in use.
@bwelles5983
3 жыл бұрын
Not only informative, but inspirational.
@terryramsey5979
7 жыл бұрын
Nicely done! Would love to see that over arm collector build video as well!
@DPShopTalk
7 жыл бұрын
+Terry Ramsey thanks! If you look in the how to section of the channel I've already done the overarm build video.
@DPShopTalk
8 жыл бұрын
Just wanted to let everyone know that I've put out a new version of this video with the new intro. I had some issues with the old intro music so I'm going to switch over some of the older videos including this one. You can view the new video here: kzitem.info/news/bejne/lZWXzaScgXOYkmk If you want to leave any comments please leave them on the new video and we can continue discussion there. I apologize for any inconvenience.
@BossSpringsteen69
3 жыл бұрын
An answer to my prayer. Thank you, Sir.
@bradsmith1046
3 жыл бұрын
Well done Dan! The health benefits alone are a huge win for folks following your mods. Thanks.
@dankohl3289
8 жыл бұрын
I made one of these panels for my Delta contractors saw using your pdf diagram! It fits perfect! Thanks very much. Used the foam idea too! Sucks like a champ!
@DPShopTalk
8 жыл бұрын
+Dan Kohl glad you found it helpful!
4 жыл бұрын
my friend. very nice. thank you. so much. be happy
@ramaroodle
7 жыл бұрын
Scary. Your shop looks cleaner than my living room.
@paulnitz9682
4 жыл бұрын
That's because he cleaned it after each project
@tegastream
3 жыл бұрын
That's what you are supposed to do with your living room as well lol
@BossSpringsteen69
3 жыл бұрын
LOL
@martyjosephson4937
7 жыл бұрын
I like the back side barrier and have built one for my Grizzly, works just fine. I do have a different approach for the bottom of the contractor saw. I took that flat add-on and cut the port out of it (after removing it). I then built a tapered chute from the full opening at the top down to 7" square bottom. I clears the floor by about 3" and attached the 4" (cut out) port to the lower end. I them placed a 1/4" plywood piece inside to channel the dust and air to the port. I works so much better then that flat plate, which always piled up with saw dust anyway.
@DPShopTalk
7 жыл бұрын
+Marty Josephson sounds like a great solution for the bottom, thanks for sharing! I need to make something like that for the bottom of my saw sometime.
@georgeanen6627
3 жыл бұрын
Yes I really would appreciate you doing another video on how to hook up this dust collection to my table saw and where to buy the clear guard first for your saw for the dust collector port thank you
@DPShopTalk
3 жыл бұрын
If you look in the video description the link to the overarm video is posted there.
@roncooke2188
4 жыл бұрын
Just started on my dust collection setup, i don’t feel i use it enough to do like you have, for now i have just made a start on the blade dust. It should be a bit of help in stopping me getting covered in sawdust. Nice video and of great help many thanks.
@rejeanwolfe3756
3 жыл бұрын
I am definitely ingested interested in knowing more. Tks a lot for sharing your knowledge.
@DPShopTalk
3 жыл бұрын
If you're looking for more info about the overarm collector there's a link to that episode in the video description.
@csimet
2 жыл бұрын
Great ideas. My saw has a heavy mobile base plywood stand that encloses the entire bottom it sits on and not the original metal one. I have a removable box to collect the large chips at the bottom that is easy to pull and empty and only use the dust collector to remove the fine stuff. I've been looking at ways to enclose the back where the motor sticks out. I like the way you enclosed the back and think I will do the same to help improve the fine dust management. Only change I will make is some type of latches to hold the two pieces together so there is no chance they can vibrate loose (I worry about it coming in contact with the belt). It is rare I do non 90 degree cuts, so I'll just pull it off when needed.
@johnchidester1324
5 жыл бұрын
Terrific ideas, I have an old Delta/Rockwell that I will be working on.
@alexspecht1705
8 жыл бұрын
awesome video Dan. I hope I can do some modifications to my table saw soon
@bufford14
7 жыл бұрын
I'm remodeling my 20x30 garage and turning it into a place where I make a few things. I have a new Dewalt DWE7491RS contractor saw with the wheels and all. This past winter I've been making a dedicated table for it, with a router as well. I like the saw but the dust goes everywhere. It has a port in the back sucking all the dust to from an enclosed hopper, but still way to much dust still gets out. I bought a brand new Craftsman shop vac that really works good, with my DeWalt planer, but the table saw is another problem. I have to stop up all the useless holes that should have been done in the factory. I have been looking for someone on here to see how they did it, and you young man have solved my problem. I will get to this soon and see if I can make it suck more dust instead of getting it all over me. I hope to have a dedicated dust collector come my way via Santa Clause. Keep up the good work, I going to check out some of your videos. See ya Mark
@jesser9134
3 жыл бұрын
I've been working on this too. Didn't close the back, but I guess something easily removable makes sense because I don't tilt that often
@sergiogomezphotography
5 жыл бұрын
Thank you! I will try the lower pan idea, I had added a collection bad but that didn't do what I thought it would. I'm subscribed.
@Allbbrz
5 жыл бұрын
Great idea with the magnets. I like your first three approaches. The last one will not work for my "garage" - err... shop.... I need to constantly move my table saw around. But I can certainly work the first three. Thanks for the video as we all know what we should do but we need some encouragement :-)
@rogerk7194
7 жыл бұрын
Good stuff Dan. Thnx for your time and videos
@henaken08
3 жыл бұрын
Great, thanks a lot, I'm struggling a bit with dust collection on my table saw. I think this will improve a lot
@4vinos
7 жыл бұрын
I liked the hood you placed on the bottom of your saw and the ones next to the belt. I will do this on my contractor saw. Please make the one you mentioned (oped hood like others have shared) Thank you for sharing. I have subscribed because you make a lot of sense and your videos are minus the music which I detest. Thank you.
@josephspina7827
7 жыл бұрын
Very clever rear cover build . I also have a contractors/high breed saw {Jet s10} i covered the openings under the top with a foam and the seams with a hvac aluminun tape.Yes please do a how to build the over the table dust collector. Thanks
@mozes42
6 жыл бұрын
Just about to head over to 80/20 Inc and put together one of those dust collector arms. Thanks for the inspiration!
@eversleyowl
8 жыл бұрын
Nice video, top tip about using foam to fill gaps.
@thomasklink3766
8 жыл бұрын
Excellent.. Love the idea of using the two part cover in the back with the magnet mounts. I have been kicking around some ideas for my old Craftsman, but you gave me the solution. Thank you, I'm surprised I hadn't run into your channel before. I'm subscribed.
@DPShopTalk
8 жыл бұрын
+Thomas Klink glad you found it helpful and thanks for the subscription!
@stevenfernandez4787
4 жыл бұрын
you're the kinda guy that\t motivates me. thanks for that.
@leehaire1300
8 жыл бұрын
Thanks Dan!!!! Have it all printed out and it will be done as soon as I can get to it. If you decide to make up a diagram of the over the blade dust collector I'll make that up also. Thanks again!!! Lee of Western Mass.
@robertdake594
2 жыл бұрын
I think any kind of dust collection while it's happening is a 'knip-N-th-Bud' ! I'd like to see how you make the overhead arm part ! Very Good Thnx
@TheMikeNan
5 жыл бұрын
Well done. Your explanations help us a lot.
@carlcarlson7253
4 жыл бұрын
I would appreciate how to video on over arm dust collection. I have same table saw so pattern for two part magnetic rear of saw filler boards would be great too. Great video! Thanks, Carl
@DPShopTalk
4 жыл бұрын
You can find both the video and the template here: www.danpattison.com/blog/2016/10/7/4-table-saw-dust-collection-upgrades
@danieltaylor8347
5 жыл бұрын
Nice mods. Looks very efficient. Would like to see video on the arm build.
@dYna77
8 жыл бұрын
Hey Dan, thanks for your videos. I hope you will get some more views soon, since i think you do great work. And yes, i would like to see how you build the arm thing...
@DPShopTalk
8 жыл бұрын
+dYna77 Thanks and I'm glad you're enjoying the videos!
@19Dennis53
3 жыл бұрын
Very nice work! One smart cookie!
@dallanwordekemper3836
7 жыл бұрын
I do like your approach to the air flow design. Let me know when you have a plan for the dust collection on the top of the saw.
@DPShopTalk
7 жыл бұрын
+Dallan Wordekemper have you seen the video about how to make the overarm collector? I don't think I'll be producing a set of plans for it since it would be custom for each saw but I show how to make one in the video below. kzitem.info/news/bejne/uXyvrZyrbWWliIo
@BobBlarneystone
Жыл бұрын
Thanks for some ideas. For the back of the contractor saw, I'm going to try making a dust director that is mount on the motor bracket mount bolts. That way, the dust director moves with the arbor carriage when beveling. For the upper shroud,could you incorporate a splitter?
@DPShopTalk
Жыл бұрын
A splitter would need to be attached to the saw itself rather than the overarm but you could add one.
@stuffsethmakes
8 жыл бұрын
Nice! I never thought to use foam to seal those gaps 👍🏼
@ChrisHodges87
4 жыл бұрын
Great example. Thank you.
@emilsabbione7529
8 жыл бұрын
Loved your ideas and look forward to seeing a fabrication video.
@DPShopTalk
8 жыл бұрын
+Emil Sabbione did you see the video on how to build the overarm dust collector?
@jamiejessup90
8 жыл бұрын
Awesome video. I have a similar Delta and liked your method of two pieces coming around the rear trunnion for the back cover. I'd love to see an over the blade how to!
@DPShopTalk
8 жыл бұрын
+Jamie Jessup thanks, glad you found it helpful. I'm actually working on the video for the overarm collector how-to video now so stay tuned for that coming out.
@DPShopTalk
8 жыл бұрын
Thanks for the comments guys!
@petechandler9502
Жыл бұрын
Yes. Please show how to build top fit collection arm.
@DPShopTalk
Жыл бұрын
The link is in the description.
@davethurston753
2 жыл бұрын
This is great. Thanks
@harrisedgar
6 жыл бұрын
Yes...!!! Let's see how you build it..!!!
@DPShopTalk
6 жыл бұрын
kzitem.info/news/bejne/uXyvrZyrbWWliIo
@ZK10002
7 жыл бұрын
Great video! Thank you!
@doubleww2
4 жыл бұрын
Waiting on how and instructions on making the dust collection system for table saw. Thank you.
@mrlifetime64
6 жыл бұрын
meticulous-great work-very neat
@davidwinn8492
3 жыл бұрын
Dan, you tha man! Great video.
@ljackson8220
3 жыл бұрын
Thanks
@roncooke2188
4 жыл бұрын
Great video i like the over arm system
@charlieking8785
6 жыл бұрын
very nice shop thery. please understand we woodworkers should learn dust control. small shops do need this system.have a rigid portable table saw but it does need a system to control dust. keep up the great projects, learning at my age is great to see different appplications in a shop. thanks.
@steventhibodeau841
2 жыл бұрын
really really would like to see a how to video on the arm dust collection feature
@DPShopTalk
2 жыл бұрын
You can find the link in the description
@NeoQJ
3 жыл бұрын
Inspiring , thank you
@VBWilhite
6 жыл бұрын
Nice job Dan. I sub'ed, liked, bookmarked your website and down loaded the plan. Thank's
@winna101ify
3 жыл бұрын
A very helpful video. I have a delta table saw similar to the saw in your video, to which i wish to add a dust collector port. i shall be following the example in your video. I am also interested if you do a video showing how to make the over blade dust collector. Thanks fr publishing this helpful video.
@DPShopTalk
3 жыл бұрын
The link for the overarm video is in the description. Glad you found the video helpful 👍
@craigburghardt8604
3 жыл бұрын
I guess you remove the back panels when you changed the blade angle? I am getting a headache trying to cut one that allows the swing of the motor and belt. Since it is almost always 0 or 45, maybe just two different back plates will solve this head ache. Thanks for the video and inspiration. Wish me luck.
@DPShopTalk
3 жыл бұрын
Yeah I remove the panels when I tilt the blade. It is very rare that I have to tilt the blade so for me its not an issue. All the best with fitting yours.
@JimDockrellWatertone
8 жыл бұрын
Another great one! Thanks for the tips!
@58Chev
8 жыл бұрын
+Jim Dockrell (Watertone) Agreed, Another great video Dan. ThanX
@DPShopTalk
8 жыл бұрын
+58Chev thanks for the feedback guys, very much appreciated!
@knowmater
2 жыл бұрын
Great Ideas!
@ronlabelle2962
Жыл бұрын
I would like to see a video on how you made this overhead dust collector.
@DPShopTalk
Жыл бұрын
The link is in the description.
@DPShopTalk
7 жыл бұрын
Have you built one of the DP Shop Talk projects? Submit your project at the link below and check out other projects that have been submitted by viewers! Also leave your comments, questions and ideas at the bottom of the page in the comments box. www.danpattison.com/blog/viewerprojects
@murphsworkshop4214
7 жыл бұрын
Thanks for sharing this info!
@davnunn1
Жыл бұрын
Where did you get the hose connector and plastic shroud from? I have made a similar collector using an after market guard. However the connection from a 67mm (2 1 /2in) hose required a step down to about 32mm and so much power is lost it doesnt work that well.
@DPShopTalk
Жыл бұрын
There is a link for the shroud in the blog article that's linked in the description.
@DennisYamaha1985
6 жыл бұрын
Outstanding video!
@StupidEarthlings
5 жыл бұрын
Nice tips. Looks like my saw too.
@quietkey2003
5 жыл бұрын
thanks alot Dan. I have the contractor saw and was about to start on my dust collection mods for it. Didn't want to use a job site saw. I'll purchase the bosch attachment through your website to you gets some coin....Peace
@DPShopTalk
5 жыл бұрын
Thanks, I appreciate that!
@carterscustomrods
6 ай бұрын
1:20 I'm not sure if the video is flipped but it looks like your link belt is put on the wrong way? I mean, its not too big a deal, but I've noticed it's noisier. It supposedly causes the link tabs to be pushed, rather than roll when they reach the pulleys, and causes the belt to wear out quicker. I say this because my first link belt, I put it on the way you have it, and it caused the belt to get very hot, and break down faster. The little tabs on the inside started to wear out and if I didn't notice it in time, one could've become so damaged that it would've broken free.
@DPShopTalk
6 ай бұрын
I think I did actually flip it around at one point but I don't have the saw anymore so I can't be sure. I think someone else had pointed that out too. Thanks for the comment👍
@carterscustomrods
6 ай бұрын
@@DPShopTalk thanks. I'm always second guessing myself (and info I have) when I see something that is not the way I have it set up. Lol
@MerkleAkrunphleuphle
2 жыл бұрын
Would similar work for plastic pipe shavings you think?
@davidnleeh4
4 жыл бұрын
AWESOME job!!
@JAYJAYJAY53
7 жыл бұрын
I was so sick of the large amounts of dust produced by my saw that I installed a plywood box on that back of my saw that allows the saw to be set on 45' angle and the blade to be raised to max.height.I use blue paper tape on the angle adj. slot in the front. The bottom has one of plastic pans that I attach my shop vac to
@celia.gallardo
4 жыл бұрын
Impressive! I want to see how you made your upper dust collection arm adapter
Пікірлер: 306