I think you may be the only one on youtube to install torque converter properly. 👍
@lsj624
5 ай бұрын
This kit is perfect. The steel plate alone weights over 9 lbs. Very heavy duty. The bearing sticks out like that to put it closer to the sprocket. The RED spring on the Driven pulley is already the correct reverse spring and works very well. Comet just paints there spring yellow. Good job Eric.
@fatbuddycat
2 жыл бұрын
Amazing. That thing looks humongous but very awesome!! I never would have guessed it can go on backwards either! Thanks for the lesson Eric!
@raymansmiley
11 ай бұрын
Thanks for the info. Putting a torque converter on a go kart for the first time you helped me out. Thank you sir
@maxberry1149
9 ай бұрын
You’re the man! I’m installing one on a motor I got for a go kart. Just the information I needed. Thank you!!
@Ham_Sandwich98
Ай бұрын
Big help!!
@armicast7803
6 ай бұрын
Thanks master! Saludos desde Mexico 🇲🇽
@MCscarfacematt
Жыл бұрын
just what i needed my secondary is just skipping on top of the pads and not engaging i am currently waiting on the reverse spring but the last tracking i have for it is passed through the usps jamaca NY international sort center
@LoweBrosRacing196
2 жыл бұрын
Hi Eric, I'm I'm interested in purchasing one of these 40 series kits, I was wondering in your professional opinion, do you think that the aluminum plate will hold up if mounted correctly as yoube shown? Will be for a 420cc 15hp. Thanks man, awesome work.
@charlesfehl1551
6 күн бұрын
I have a 301 predator engine. Will that torque converter fit into a golfcart to replace the gas engine which locked up and rusted. I don't understand how to connect this to rearaxle without a drive shaft. Lost in Ohio. Need help for this 82 yr old folk
@DoctorSquash
8 ай бұрын
Great educational video
@cristianalonso13
16 күн бұрын
Hello good sir. So i instsalled this but my go kart wheels spin on idle. I noticed my clutch doesnt go all the flat and is still out a little .could this be my issue? I ordered a new cluth. I hope it helps lol
@AJC-jo3ds
2 жыл бұрын
Can you use this on a 212 predator? I currently have a 30 series and break belts often…
@rf4215
Жыл бұрын
Question maybe you can answer. Yerf dog go kart worked before breaking swing arm. Replaced it with identical swing arm and also identical sprockets and chain. Put it back together and belt slips...won't propel the cart. Driver and driven unit are used but were working before.
@TheGrayGoatGarage
Жыл бұрын
I would need to see it. Send pics to help@ombwarehouse.com and I will take a look
@dustinjohnson2116
Жыл бұрын
What about when u use a jack shaft that is with the motor mount.
@TheGrayGoatGarage
Жыл бұрын
That is awesome!
@dustinjohnson2116
Жыл бұрын
@@TheGrayGoatGarage I can’t seem to get them lined up centered.
@teemuviitaniemi
2 жыл бұрын
Good video! Thanks.
@MrJakedaddy
11 ай бұрын
Do you have a video of this running? I’m curious as to how long the belts last as one side is generally slanted in more than the other.
@duanefrey2449
2 ай бұрын
Hi Eric, what can I do to stop my primary from grabbing the belt @ idle tried a new belt same issue idle is set as low as I can go duramax 440, I put into a b200r coleman thanks I'm puzzled
@TheGrayGoatGarage
2 ай бұрын
We can change the springs in the driver to the red springs to get the driver to engage at 2000 rpms www.ombwarehouse.com/comet-40-series-red-springs-set-of-3.html
@igokarts4510
2 жыл бұрын
On the driver/driven alignment the driven moving sheeve should be matching the drivers fixed sheeve at full engagement. This will cause a bit of misalignment when not active. Does that seem right or am I losing my sh!t?
@TheGrayGoatGarage
2 жыл бұрын
I don't know if you are losing your stuff, but I can tell you that does not matter with these units. The symmetric belt is forgiving. Also consider that the original Comet units used the driver mounted conventionally and the driven had the hub inboard...same thing as what you see here, just in reverse! Trust in the Goat...you will be fine!
@ChrisBusy
2 жыл бұрын
You forgot to show the versatility of adding a band brake unit! Thanks for the good quality video, keep them coming Senior~
@igokarts4510
2 жыл бұрын
@@TheGrayGoatGarage "In Goat we trust"!
@marjuspjeci4097
6 ай бұрын
hi, I also fitted the same kit, when I walk 2 km I touch the belt and it overheats why?? yours is the same i.e. does it overheat??? or is it normal?
@KVofficial112
4 ай бұрын
Can you use a belt with the set up instead of chain?
@TheGrayGoatGarage
4 ай бұрын
I am not sure what you mean by that. The torque converters use a belt between the two clutches and then a chain to the axle sprocket. I am not aware of a pulley for a belt that will go in the torque converter
@morraderi
7 ай бұрын
Great video. It is indicate for what power?
@TheGrayGoatGarage
7 ай бұрын
A40 series can handle up to 25 HP when geared properly
@ronp5778
Жыл бұрын
Hello, I have a question. I've read that the 30 series tq is good up to 8hp or there about and a 40 series tq is good for up to 16hp or so. My question is would there be any performance gains by using a 40 series tq on a built 212cc predator engine putting out 15hp? I realize you would need to put a sleeve on the 3/4" shaft to bring it up to 1" for the larger front pulley to be used.
@TheGrayGoatGarage
Жыл бұрын
The 40 series units are very heavy and the snowmobile guys have been known to break cranks. There is a 40 series driver available for 3/4" cranks www.ombwarehouse.com/comet-44c-magnum-drive-clutch-3-4-.html but I do not recommend using it unless you add an outboard bearing and support for the weight. I have seen 30 series converters used on 16 HP engines. There are some modifications that must be done, but they will support the power. The 1" drivers use a 1/4" wide key and the 3/4" cranks and drivers use a 3/16" key. That makes it very hard to adapt!
@davidmorgan8612
8 ай бұрын
You are showing a steel and aluminum back plate. The unit comes with an aluminum back plate. You are not using the aluminum one that comes with it, why? Where did you get the steel one that you are using? Did I miss something you said or meant?
@TheGrayGoatGarage
8 ай бұрын
It does not matter what plate it comes with. The installation is the same. I feel the aluminum plate is stronger and I prefer it over the steel plate www.ombwarehouse.com/40-series-1-torque-converter-with-steel-mounting-plate.html
@davidmorgan8612
8 ай бұрын
@@TheGrayGoatGaragethank you for getting back to me so quickly. Your input will help.
@teeter-built5288
2 жыл бұрын
Can you mount a sprocket on the backside of the the mounting plate behind the engine? Or does it have to be between the mounting plate and the driven pully?
@zombiebloodsparkle1
Жыл бұрын
Hey, I have a question that I cannot seem to find an answer for anywhere. I want to install a 30 series on my go-kart, but the problem is that the sprocket needs to be on the outside instead of the inside. Is it possible to place a spacer where the sprocket would have been on the inside and mount the sprocket outside?
@TheGrayGoatGarage
Жыл бұрын
Nope! That will put too much pressure on the plate and it will break!
@zombiebloodsparkle1
Жыл бұрын
@@TheGrayGoatGarage If i weld a piece of metal to the cross bar and add a bearing that goes on the shaft would that help hold it up and prevent it from breaking?
@ligmaballs1405
5 ай бұрын
My driven pulley bolt is too long for the amount of thread I have. Did you use a different length bolt?
@TheGrayGoatGarage
4 ай бұрын
No, I did not, but we have to work around Chinese tolerances. Get a shorter bolt at the hardware store and you will be fine!
@marjuspjeci4097
6 ай бұрын
Ok
@Cherokee-sz7xi
Жыл бұрын
I got a 40 series china made. 420 predator turning ccw looking at shaft,Do I need the ccw green spring on my driven? Thanks
@lsj624
5 ай бұрын
Can I have the cover dimensions please? Basically plate to outside of cover. Thanks. Good vid.
@TheGrayGoatGarage
5 ай бұрын
I am sorry but I don't have that measurement and do not have the parts here to get them measured for you. I work offsite from the warehouse. My apologies
@lsj624
5 ай бұрын
@@TheGrayGoatGarageNo worries. Cheers.
@plainsabertooth7828
3 ай бұрын
Can you attach a go kart transmission with reverse gear?
@TheGrayGoatGarage
3 ай бұрын
Anything is possible! Just not easily Most reverse boxes would use a driven unit in the input shaft
@plainsabertooth7828
3 ай бұрын
@TheGrayGoatGarage the one I'm looking at has been tested for the 30 series torque converter but not the 40 series.
@mitchdoman8726
2 жыл бұрын
Where can I buy a stage 4 clutch and torq converter for a trail master 200 hurricane
@treycurbow554
Жыл бұрын
I bought the same one and my driven pulley goes the opposite way how do I fix it
@TheGrayGoatGarage
Жыл бұрын
If you are you referring to the reverse spring in the driven, we have that here www.ombwarehouse.com/comet-40-series-reverse-wind-spring-204524a.html
@andrewnemchik7576
2 жыл бұрын
I installed the same kit just the way you did and did not put a reverse wound spring and my golf cart only does 10 miles in hour and rpm go really high. Is this because I need the reverse wound spring? Please let me know and thank you
@TheGrayGoatGarage
2 жыл бұрын
Yes. Without the correct driven spring as soon as the driver clutch engages the belt the driven gets yanked open.
@TimothysTractors
Жыл бұрын
You might also consider a larger sprocket. I had the tiny sprocket that was included and got 6-7mph on my golf cart. Upgraded to a much larger one and am getting over 30mph now.
@andrewnemchik7576
Жыл бұрын
@@TimothysTractors yeah i was stumped for a while but then i put a bigger sprocket on a few months ago and it goes about 32
@OscarMartinez-js1it
2 жыл бұрын
Can you put the 40 series driver and driven pulleys on a 30 series mounting plate
@Misifusmiau
Жыл бұрын
Of course not, the mounting plate is half the size on a 30 series.
@jacjumpin7471
2 жыл бұрын
You should saftey wire those bolts
@TheGrayGoatGarage
2 жыл бұрын
That is a great idea, I have just never had any issues with those bolts loosening
@samuellemaster7215
Жыл бұрын
Can you put this on a 12 hp Kohler lawn mower motor
@TheGrayGoatGarage
Жыл бұрын
If the engine has a 1” diameter crank, yes, you can
@issaclopez7445
Жыл бұрын
Hi I know this is a very late comment but how did this hold up thinking about getting one but dunno if it’s good enough to put down money for it
@TheGrayGoatGarage
Жыл бұрын
We sell a lot of these with very few issues. As long as it is installed properly it will easily hold 25 HP and last a long time. The other option is to spend $400+ for genuine Vomet parts!
@TheGrayGoatGarage
Жыл бұрын
Comet!
@issaclopez7445
Жыл бұрын
Thank you!
@dustinjohnson2116
Жыл бұрын
How do you know if you need a reverse spring ?
@TheGrayGoatGarage
Жыл бұрын
You have to look at the buttons on the driven unit and make sure that when the driver grabs the belt the driven unit is not yanked open Send me some pics to help@ombwarehouse.com and I can verify for you
@dustinjohnson2116
Жыл бұрын
@@TheGrayGoatGarage ok will do tomorrow after I receive the new driver and driven pulleys. I will send you what I ordered. Thx
@dustinjohnson2116
Жыл бұрын
@@TheGrayGoatGarage email sent
@Misifusmiau
Жыл бұрын
A 420 chain on such a big engine is a bad idea. The 420 chain is for a maximum of 125cc engines.
@8822fitzy
5 ай бұрын
How do you figure? 😂
@franciscovazquez4073
Жыл бұрын
mine keeps burning the belt any suggestions? 😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢
@TheGrayGoatGarage
Жыл бұрын
Yep! Change your gearing! Need to know more about what the setup is. Email me some pics to help@ OMBwarehouse.com
@Misifusmiau
Жыл бұрын
Engine is too powerful lol.
@koljag5
2 жыл бұрын
Is this going on a mini bike?
@TheGrayGoatGarage
2 жыл бұрын
Haha. Nope! I don’t care for big block engines on Minibikes. I would rather have a rowdy small block!
@koljag5
2 жыл бұрын
@@TheGrayGoatGarage I figured as much, I just assume you are always working on mini bikes.
@mihkelsepp72
2 жыл бұрын
I think you meant to say CVT (transmission), not torque converter. Torque converter is type of fluid coupling unit, which acts a lot like a clutch would. While CVT changes the ratio between input and output shaft rotation speed. PS. Keep up the good work
@TheGrayGoatGarage
2 жыл бұрын
These units are commonly referred to as torque converters and have been for the last 50+ years. If we called it a CVT nobody in the go kart or MiniBike world would know what we were talking about!
@WhatIsTheWheel
2 жыл бұрын
@@TheGrayGoatGarage And they are still mechanical torque converters. There are some really big ones on DAF cars from the fifties, they ran two one driving each rear wheel.
@TheOriginalAndysGarage
2 ай бұрын
That belt looks too tight and your clutch is on backwards
@TheGrayGoatGarage
2 ай бұрын
The driver unit can work in either direction. It does not matter which way it is mounted on the crank. The belt is the correct length for that application
@nightstarking
2 жыл бұрын
10 tooth 40/41/420 sprocket not 12
@TheGrayGoatGarage
2 жыл бұрын
Hi Aaron I have not been able to find a 10 tooth 420 chain sprocket with a 3/4” bore
@nightstarking
2 жыл бұрын
Your description is wrong you said it's a 12 but it's a 10 tooth Check out the description on OMb OK bub
@jasonbledsoe9379
Жыл бұрын
I think you should post a how-to video in great detail to perfection, then once you have done so, then you can be a critic on minuscule topics of someone else's video. Ok bub!
@nightstarking
Жыл бұрын
@@jasonbledsoe9379 just stating the obvious that should not anger you but maybe you just like misinformation go make American great again with your rainbow RC troll streaming dik riding Obama as
Пікірлер: 90