I have a 1970 cutlass SX I run a beefy stock stall speed converter from Coan racing . The 455 builds alot of torque down low so it really does not need a stall speed to make power. If you unleash a high stall speed it is just going to roast tires. My car has a 3:42 gears and when I bought it many moons ago It came with a small radius converter and was stalling somewhere 3800. Also I have a full 3 inch dual exhaust with NO crossover or x pipes . I have a 750 double pumper with mechanical secondaries and when you nail it its all power . Many people think back pressure is gospel, The 455 runs air-boats , cars and marine applications. It likes wide open exhaust. You have a ground pounder :)
@bobdimartino6738
Жыл бұрын
i had the 850 double pump mechanical secondary dual feed line type c heads edelbrock intake no bog at all lite up the tires at 30mph 1969 motor 290 duration cam
@Marc816
3 жыл бұрын
THE 455 OLDS WAS DESIGNED ALMOST 60 YEARS AGO, BUT WITH A FEW SIMPLE MODS, IT CAN RUN WITH TODAY'S BEST!!!!!
@oldsman4446
3 жыл бұрын
Very true but for some reason people swap it our with a chevy!!! Don't know why. I have a 1980 cutlass and i put a 69 olds 455 h/o in it and it bolted right in and it makes over 520 foot pounds of torque, more than a chevy!!! And parts for it are ez to find! Its only 3800 lbs w the big block. Make sense to keep it oldsmobile.
@Marc816
3 жыл бұрын
@@oldsman4446 "Very true but for some reason people swap it our with a chevy!!!" - I HAVE NEVER LIKED CHEVS. ALMOST ALL THAT I HAVE DRIVEN & SEEN OVER THE YEARS WERE JUNKBOXES & DEATHTRAPS.
@JdmDRFTkid
Жыл бұрын
They’re like the B-52. 60 year old technology, but modern upgrades keep ‘em still going to this day and well into the future. Can’t go wrong with the Olds engines
@justinmartinez5952
2 жыл бұрын
I'm 21 and never thought I'd be into gbody or cutlasses it was handed down to me when my uncle passed away and I inherited a 84 2 Dr brougham and Boi did it need work so I ended up getting another 4dr that was clean in and out and I happen find a 455 and immediately threw that in their. Learned alot about the car I used a turbo 350 trans from Pontiac trans am cause I didn't want to change drive shaft and also uses the same cross member and bolts right up to the 455 and I was able to use the original exhaust and now I have a fast boat
@glennmanchester5335
2 жыл бұрын
I bet and fast for cheap has always been my moto lol listen curve the HEI distributor and put lighter weights and springs bring that advance in quicky those lower compression stock motors love advance in s hurry and make sure the advance mechanism is all in. Good working order w light springs etc don't worry about initial timing as much as total timimg and when you get total timimg that's what is important for performance set it up for that and If she starts good and sounds happy is responsive and we'll you can tell when a motor sounds happy Starts happy and is happy do all that to that 455 and use a good hot coil a really good module in the distributor a good cap rotor and good plugs and hold on I hope your running the. Original quadrajet carb cuz you can't beat them for reliability and performance with any carburetor out there also gas mileage is way better with a q jet when you stay out of it lol. Love the q jet moan too my buddies heard me coming for miles and miles away with that moan lmao
@fredfuller2281
3 жыл бұрын
good ole Olds 455 rocket v8 build!!
@angelo57a51
2 жыл бұрын
Sounds awesome! I have a 69 Cutlass with a 455 that I will be rebuilding soon.
@marcmo7138
Жыл бұрын
I used headers from flow tech for my 1988 Cutlass 403 build. fit fine. Small block but you might want to check them out for a 455
@joeymccullough2716
2 жыл бұрын
Life would have been so much easier if you had removed that hood, first!🤔😆 She’s gonna be a beast when you get her back together-the way a 442 should be👍
@macman987
2 жыл бұрын
I think if you would've taken the hood off it would've made this alot easier?
@moneyandmuscle400
2 жыл бұрын
Been here before. Those gbodies with a olds motors are a pain putting headers on
@jonathanduke8295
3 жыл бұрын
Keep em comeing man.
@BMFcustoms
7 ай бұрын
What brand are the headers that you installed (I know this is a old video I hope you see this comment ) I have a 1980 442 with a 455 and I’m only finding one company ARH that makes headers , are you running normal 455 long tubes and just making them fit in this video ?
@cassw1485
5 ай бұрын
Nice build
@dboyxtrill4296
3 жыл бұрын
How did you hook up the ac?
@jameskarchner8218
3 жыл бұрын
Noticed a C head casting , 68 or 69 455 ? . Came out nice , is it an 85 442? Didn't see a center brake light . Will probably bury the 85 speedo in second or third gear ! The 84 hurst looks nice too. Is that a 307 still ,or a 350 ?
@BigGeorge3397
Жыл бұрын
My Casting says CA. Do you have any knowledge of what that means?
@bobdimartino6738
Жыл бұрын
@@BigGeorge3397 i had a 69 with c heads regret selling it
@atomix62t
2 жыл бұрын
My Very First Car Was A 1984 Hurst Olds With A ‘Moon Roof’
@lennycoluccio9129
2 жыл бұрын
What oil filter # did you use
@w41duvernay
10 ай бұрын
Derek, I would like to know what brand and part # of the headers you used on this swap?
@thefakederekrufle
10 ай бұрын
Not sure, flow tech maybe 🤷♀️
@armyjeep4
2 жыл бұрын
So you don't need special motor mounts? You can use the 307 mounts?
@thefakederekrufle
2 жыл бұрын
Yeah, stock engine mounts
@gregoryduffin524
3 жыл бұрын
Cam Break in? , dumping the exhaust just past the trans mount, good luck with it bro
@ayemanedrico8893
Жыл бұрын
What motor mounts did u use
@thefakederekrufle
Жыл бұрын
Replacement for a 307
@BigGeorge3397
Жыл бұрын
Good job! What all brackets did you use to make that 455 work in your Cutlass?
@thefakederekrufle
Жыл бұрын
Original ones from the 307. Pulleys and brackets
@BigGeorge3397
Жыл бұрын
Thank you! One more question. Did you have to modify the ac bracket?
@thefakederekrufle
Жыл бұрын
The front bracket got cut then extended with a donor section from the air pump.
@BigGeorge3397
Жыл бұрын
@@thefakederekrufle It would be awesome if you can show a video of modifying the a/c bracket
@MrShade-tree
2 жыл бұрын
why is the engine red ?and why didn’t you prepare and or painted the engine bay before you put the engine in there just curious
@garywesterhouse851
2 жыл бұрын
scrap the headers and find some 455 dual manifolds will run just as good i have a 455 and got it in 82 and had it in that car plus a few more i gave up on headers years ago and some tru dual manifolds are a lot less hassle and will seal alot better
@BigGeorge3397
Жыл бұрын
I've heard the American Racing headers are pretty good. Do you think they wouldn't seal well?
@garywesterhouse851
Жыл бұрын
@@BigGeorge3397 not sure on that have not used those but the headers come with a few problems extreme heat on starters ground clearance gaskets i always used metal stock gaskets and doubled them butt the heat would wear them out fast since i went to stock manifold duals i have never looked back and if i did go back i would use the shorty style not cheap and i think their gasket surface is thicker ..
@BigGeorge3397
Жыл бұрын
Ok. Headers maybe a no??? What size pipe do you run for your duals?
@garywesterhouse851
Жыл бұрын
2 and a half inch and I use the straight through glass packs sound good
@petercarr3686
7 ай бұрын
Wow, 3 days for an engine swap? 1 1/2 days tops. Ok, first off, take the frickin hood off. Assemble everything including headers before. Line up, drop and slide on heavy rear angle, headers will slide right by frame. Done this 6/7 times with no lift. And I'm not a certified mechanic. All the cars are still running yrs. later.
@jeffhargett6078
3 жыл бұрын
what air cleaner are you going to run on that?
@erickton1
3 жыл бұрын
I'm new to the 455 olds im building the engine basically from scratch at the shop i was wondering help me by telling me what all sensors and small components it needs and is the fuel pump is outside the tank
@wildrosegarage4208
3 жыл бұрын
It doesn't need any sensors. Factory fuel pump is on the front passenger side of the block.
@whirlwind8825
3 жыл бұрын
Buy a new sending unit with a new filter sock for the fuel tank. That sending unit tells the gas gauge how much fuel is in the tank
@marcoshernandezjr.4474
2 жыл бұрын
I have a 84 delta 88 olds. 307 5.0... what engine can I put in it? I heard the 442 olds what fit... but if so, what yr make would I look for?
@BigGeorge3397
Жыл бұрын
I believe anything GM makes
@outdamudtv
2 жыл бұрын
Do u still have this motor bro
@gbodyp2725
2 жыл бұрын
Do you have any cutlass doors for sale
@deontamccray4164
2 жыл бұрын
Can you tell me which belts you used for the alternator and power steering???
@bookkeeper9902
8 ай бұрын
Why in the world would you not take the hood off? Grinding metal without eye protection?? Work safe and smart not hard.
@faustthehammer8706
2 жыл бұрын
Take the hood off I cracked my windshield for that on a g body
@edwinrufle7070
2 жыл бұрын
I have an electric vacuum pump you can have. Never used.
@lennycoluccio9129
3 жыл бұрын
Please what headers are they
@lennycoluccio9129
3 жыл бұрын
I have 83 olds with olds455 im gamed to put those headers on what 70 and # pleases thank you
@thefakederekrufle
3 жыл бұрын
11154FLT
@lennycoluccio9129
3 жыл бұрын
Whats the specs and headers in that 442 86
@lennycoluccio9129
3 жыл бұрын
That's what I'm using a 75 degree iol housing
@lennycoluccio9129
3 жыл бұрын
What # iol filter
@rickstephens1130
3 ай бұрын
You have already ruined those headers! And you have wasted the 200.00 bucks that you paid for them. Those will never work
@SupDoggyTV
3 жыл бұрын
What transmission goes best with a 455?
@Flatlandproductionz
2 жыл бұрын
400 b.o.p but that built up 200 will handle it. You want a 4 speed with lock up action.
@glennmanchester5335
2 жыл бұрын
Or a built up 700r4 but yeah your right a overdrive trans is always best a lower first and a fourth gear is always awsome but a 400 w a shift kit will take way more abuse lol
@SLJ2137694
11 ай бұрын
@@Flatlandproductionz200 is not a 4 speed.
@Davey-Drums
2 ай бұрын
I noticed that someone is making new copies of the original 70 W/Z factory performance dual exhaust manifolds. I actually got lucky and found some originals. Headers are such a pain! I have not installed them yet, but I think they will fit my 81 Cutlass 455 wagon. I originally just used the factory crossover pipes from my 69 455. My heater box prevented me from installing some really nice Speedmaster aluminum valve covers. I was thinking about modifying it with fiberglass to make room and all, but not yet. I had to drill holes in heater box to get pushrods out.
@rickstephens1130
3 ай бұрын
You are going to have a lot of problems later on down the road if you don't get these things figured out now. And you don't want that exhaust running up against the firewall at all, you will start having electrical problems and possibly a fire because those headers will get red hot and transfer the heat to everything that is on your firewall. I have a set of headers on my 1966 Oldsmobile, and I have seen how hot they get
@glennmanchester5335
2 жыл бұрын
Headers are always a a pain in the ass always and I've never been a fan especially on a stock motor the gains you see are so not worth the work to use them then they leak later on as well even w the best gaskets etc you'll. See pain in the Ass
@d-money314
2 жыл бұрын
I had an olds 455 put in my 86 442 two years ago
@sewerpipecasso8750
3 жыл бұрын
Keep those videos coming bro
@Flatlandproductionz
2 жыл бұрын
So does the 200 shift fine with out the quadrajet emmisions carb? Thats how those shift from the electronics of the t.p.s.
@marcmo7138
Жыл бұрын
Pretty sure it is the detent cable that does it.
@ssw4022
3 жыл бұрын
Any engines/transmissions for sale??
@jameskarchner8218
3 жыл бұрын
You didn't have to take off the hood? Amazing..
@jermainebankstonsr.3379
9 ай бұрын
Derek...i have an olds 425 and if you can remember i need the headers brand and number
@83HURSTROCKET
Жыл бұрын
Derek do you have a video of you installing the intake manifold? I have an OLDS 455 in an 83 hurst and want to dress it up, and place a new intake manifold. Have never done it so need a little help brother
@nateb3703
Жыл бұрын
How are you liking your 455 in your 83 I have the same setup I should have it back from the mechanic this week
@richardkauffman924
3 жыл бұрын
Could you have used shorty headers? You might have had better clearance.
@BigGeorge3397
Жыл бұрын
Who makes a short header for Oldsmobile in a Cutlass?
@thereluctantgearhead4544
2 жыл бұрын
I used the Hooker Super Competition 455 Olds in a G-body swap headers. They fit like a wet dream. But they ain't $200 bucks.
@thereluctantgearhead4544
2 жыл бұрын
I have a 79 Cutlass tucked away I swapped a bunch of Olds engines into. Ran 6.80s in the 8th with a healthy 69 455. Drove it everyday for 2 yrs.
@michaels.ramsey7803
2 жыл бұрын
back in high school (mid 90s) we looked for old square body chevy pickups with oldsmobile diesel engines and swapped the 455s in them. Instant smoke machine.
@faustthehammer8706
2 жыл бұрын
They make a diesel 1 3/4 tube header for g body's for olds
@timothybrown3495
3 жыл бұрын
Bro do mines lol
@Svazquez510Gamingsubscribe
Жыл бұрын
What’s how did you get start I have a 455 just making explosions
Пікірлер: 91