Life would be easier and less likely to damage the hub plate by extracting it using the tapped holes around the centre boss. Obtain a disc larger in diameter than the boss, something like 60mm dia x 3mm thick. Drill some clearance holes to match the PCD for 3 of the 6 tapped holes around the boss and attach using some M4 bolts, You can then use a 2 or 3 legged puller around the disc overhang to safely remove the plate. You would also need to drill a clearance in the centre of the disc to lower it over the spindle before attaching the M4 bolts
@EbikeRepairs
5 ай бұрын
Great idea!
@jpvSoccer
9 ай бұрын
hi, big fan here :). just noticed your Flux can; I still use my dad's old Flux and never saw another one like it until this video; good stuff that Flux :).
@EbikeRepairs
9 ай бұрын
They still make it! Fluxite - 'the best flux known'
@bobravenscraft5376
Ай бұрын
Cable ends etcetera NEVER EVER EVER THROW ANYTHING OUT
@EbikeRepairs
Ай бұрын
Must hoard more parts
@therealkirby101
Ай бұрын
hi, ive just come across your video after searching for hours, please tell me you can help with fixing my hub motor? do you have a place i can send my motor for repair please there isnt anywhere that will deal with this type of hub unless its a top of the range name branded ebike. Hopig you see this and can make this 1 guy happy. subbed to the channel anyways 👍
@EbikeRepairs
Ай бұрын
Hopefully! Yes I do, ebikerepairs.co.uk Send me a photo of the motor - I'll see if it's something I can work on thanks
@chrismartin6427
2 ай бұрын
Dude I know you're in the UK I'm down south near Brighton where is your shop I need someone to sort my hub motor out
@EbikeRepairs
2 ай бұрын
On holiday currently but back 14th may, I'm normally not too far from Brighton in Bexhill 👍
@chrismartin6427
2 ай бұрын
@@EbikeRepairs ok I will message you after the 14th hope you enjoy your holiday I will be needing a pcb and Hall sensor replacement
@pavlovauk9162
4 ай бұрын
Can you tell me why you didn't just cut it off and solder new cable? Then isolate properly.
@EbikeRepairs
4 ай бұрын
It's ugly! Often damaged at the entrance to the axle so I just replace the whole thing. But there isn't really any reason you couldn't do it.
@Justforyoulot
2 ай бұрын
I have the same problem my wire has like 6 wires in side big ones and small ones have not opened it yet I can see in the spit big ones and small ones I can't find the right extension cable it's got 3 pits then 8 little pins next to the beers pins (3+3+2) have you got a link yo where you have bought your from please as iv looked all over for the right one, thank you and your videos are very educational keep up the good work 5 🌟
@EbikeRepairs
2 ай бұрын
Just check on Amazon UK for hub motor extension cable and cut the end off 👍
@mrgeorgeturner
8 ай бұрын
Sweet video. I got the same issue, just struggling now to find replacement cable. I can find the ones i got now but i want the quick release wire for it. Where abouts did you get the cable from?
@EbikeRepairs
8 ай бұрын
AliExpress for this one 👍
@user-zi1hv3fk3k
6 ай бұрын
Where did you get the replacement cable? Great informative video by the way!
@EbikeRepairs
6 ай бұрын
Aliexpress. Check out 1000w ebike motor cable. Thanks!
@eliezerortizlevante1122
4 ай бұрын
amazon has a lot of those 1000w cables for $10. Extension cables. i got 4 just for replacement purposes
@StevenPerez-fl3wk
28 күн бұрын
My hub motor axle broke I need a new one where can I find that part
@EbikeRepairs
22 күн бұрын
Unfortunately it isn't easy to find one unless you know your exact motor specs, often cheaper to get a whole new kit from eBay!
@revparsons3tl
Жыл бұрын
I have you ever used ferrofluid to put inside the rear hub motor
@EbikeRepairs
Жыл бұрын
I haven't, but I've used ATF instead :) It's much cheaper
@revparsons3tl
Жыл бұрын
@@EbikeRepairs is OK to use on the hub magnets you got link please
@EbikeRepairs
Жыл бұрын
I'm not sure actually - it may cause them to become unstuck...
@marklouch
Жыл бұрын
@@EbikeRepairs 😢
@michealfraser2351
5 ай бұрын
Canu use any old wires?
@EbikeRepairs
5 ай бұрын
Technically yes, but correct motor cable would be best! As ratings etc. differ
@stan140574
Жыл бұрын
Can you fix bafa hub motor wire is broken thank you
@EbikeRepairs
Жыл бұрын
yes sure - all contact details on our website www.ebikerepairs.co.uk thanks
@user-hq3hc7ou5v
Жыл бұрын
Its too bad we can't see what you're doing or hear what you're saying.😢
Пікірлер: 33