Little bit of investigating from your advice helped me a bunch. Koodos to you bro. Thanks, again. Enjoy your day and God bless 🙏 ❤
@petercriscuolo103
Жыл бұрын
Learning Alot about these scooters.I am buying a Tao Tao 150 next month.Helps to know some things.Thank You.
@toddrapp7904
Жыл бұрын
I’m a Tao dealer .
@louisbasskicker3084
2 жыл бұрын
Really enjoyed your video. Wish you were in LA. My Chinese xpro ninja 125cc front blinkers dont blink but the rear do work after installing a new relay. After watching your very informative video, I am going to check all connections now.
@neomayad
3 жыл бұрын
you should put part 1 and 2 in the description. they're hard to find in KZitem algorithm
@mikefiegl8772
Жыл бұрын
Good video your good at telling it the way its is! A+ i have every thing working but no heard lights>dealer set the bike up ! i went for a ride sat down on the seat the scooter Shut off? Its a Dongfang 300 .i see the wireng problems! but no head lights can you help out om this one!??
@reginaldb.campbelljr.7451
2 жыл бұрын
Thank you for the DYI video
@michaelharris8346
2 ай бұрын
Both my headlights stopped working at the same time it's a tao tao blade 50cc not sure what I'm looking for but I found your video haha
@toddrapp7904
2 ай бұрын
@@michaelharris8346 if both went Out , chances are the ground plug backed out of the plug
@dean3434
3 жыл бұрын
Todd. Great information about Chinese scooters. I'm trying to subscribe to your site but it's not working. I'll try again. Question: I'm interested in the Ice Bear 300cc trike. Any thoughts on those?
@toddrapp7904
2 жыл бұрын
Personally I would stay away from the 300. They are having problems with the rear ends . Icebear is currently working on the problems but are not selling any at the moment until it is fixed.
@seanmayo206
3 ай бұрын
What is the red plug with the jumper wire on these maddogs
@buckmajor
3 жыл бұрын
Help! I have no blinkers? I changed the relay indicator but still not working. I noticed the connector to the cable is rusted thinking if that is the problem?
@nathanhearld474
5 ай бұрын
Did you not watch this video
@carlkennedy2499
Жыл бұрын
Hi theee good good video. Good workmanship. I have a problem with my scooter. I turned tye ignition on and all my indercators are flashing 😮😮 do you no wot it may be its led from factory and was all ok working. But found that the indercators sre all flashing at tye same time
@toddrapp7904
Жыл бұрын
Some Have a red flasher button on the dash like a car . Is it depressed and on?
@olearyfilmz7677
2 жыл бұрын
I work on these and I always run into problems with no crank no start and now I know how to fix it!
@jodyholcomb3738
Жыл бұрын
We're u located
@toddrapp7904
Жыл бұрын
@@jodyholcomb3738 Jackson Missouri
@toddrapp7904
Жыл бұрын
Most are brake switch issues or bad solenoid
@shaunaromine3709
2 ай бұрын
You left me hanging. Once you switched to the handle and master cylinder you didn't go back to all the wires that weren't attached and show what goes where. I'm in that spot and you almost got to that but diverted. Can you help with those unattached wires?
@toddrapp7904
2 ай бұрын
@@shaunaromine3709 check the back of the plugs . They always back out of the back of plug .
@mr.wildwood7342
4 жыл бұрын
I am in the process of converting a 2019 Xmotos 250cc dirt bike to street legal I have purchased all parts to do this my question is can I use the stock wiring harness that came with the bike? I will check to see how many wires come out of stator and my bike did come with a battery
@toddrapp7904
4 жыл бұрын
Mr. Wildwood . I actually have a 2020 XMOTO 250. I will have to look. It shouldn’t be a big deal since it already has a battery and regulator for charging. Front brakes already have a brake switch attached to bottom.
@clifflandes
7 ай бұрын
i have a 200cc doang fang super scooter. the lights work except for the head light and the lights seem a bit dim on the dash and such, what is the issue and how to fix it???????????
@toddrapp7904
7 ай бұрын
The voltage regulator is week or bad . Check headlight bulb. The headlight gets its power from Regulator . All other lights are from battery .
@pandaking3658
11 ай бұрын
Thank you
@ManuelGutierrez-be1ci
3 жыл бұрын
How do I figure out the wiring to hook up the blinkers when the colors are the same? Do I test them and how? I don’t have the money to pay someone so I have to do it myself.
@toddrapp7904
3 жыл бұрын
Front right blinker is pink Front left is brown. Rear right pink Rear left is brown The problem with vinos are the rear blinkers housings will both have brown wires coming out of the blinkers . So be aware of that. Taillight is purple/violet same as main headlight power Brake light is blue-white Black is ground
@hakeemfb3
3 жыл бұрын
@@toddrapp7904 is this wiring color coded the same for all scooters or it varies between makes models?
@toddrapp7904
3 жыл бұрын
@@hakeemfb3 most Chinese scooter have similar coding . Blinkers are usually light blue and orange with green(ground ). Headlight white , blue and green ground . ( white and blue are your hi and low wires) Ignition switch is red(hot), black(on), green (ground). Black with white stripe is kill So when you turn it on it connects the red and black. Off is green and black with white stripe connected. Start button yellow with red stripe .
@banditmorrell
3 жыл бұрын
Have a turn signal bulb not wanting to work.. thought it burnt out and even with new bulb wouldnt light up
@ryanmonti4903
6 ай бұрын
Fix the turn signals, why? It's not like they are going to get used anyway, at least not here in the Philippines...
@Dydda
11 ай бұрын
Please show the combination of colors because i have many problmes with this. Tku
@ardakaraoglanyan6319
Жыл бұрын
Dear sir, i'm going nuts... My 50cc GY6 scooter's back park lights not turning on... Front park light, ok. Brake Light, Ok. Blinkers, Ok. Bulb is also okay. I'm checking connection with a light pen connected to ground, there is light on the pen. But some how not enough voltage is coming for park light. Can you please point where to investigate? :(
@toddrapp7904
Жыл бұрын
I don’t know if I have seen a scooter with parking lights . Most just have tail light , brake light , blinkers and some have running lights .
@ardakaraoglanyan6319
Жыл бұрын
@@toddrapp7904 In here they call parking light that the one allways runs. One on the headlights and one on the tail. The one on the tail has one bulb but two functions, one low light allways runs and it gets brighter when brake applied. The one should allways runs doesn't work properly.. (No light comes, looks like lower voltage than it requires to lit, because when low voltage light tester touches the socket it lits)
@brianbolt3721
6 ай бұрын
Thanks
@thetruthhurts922
Жыл бұрын
Good vid 👍
@carlkennedy2499
11 ай бұрын
Dose rhese lights have a light controller like a little regulator
@toddrapp7904
11 ай бұрын
There is a voltage regulator that converts power from stator to run headlights and charge battery . Blinkers and tail light run off battery
@vijayakrishnannair
10 ай бұрын
Nice 👍
@prathamchavan7193
3 жыл бұрын
if I turn on headlight, brakes works electric scooter hero Optima
@danielsolivan6347
2 жыл бұрын
my front lights com on but i dont have no night lights in the back can someone tell me what might be wronmg
@stefanandersson5604
3 жыл бұрын
Halleluja! Some Times it's Essy! 👍🤠
@ManuelGutierrez-be1ci
3 жыл бұрын
I figured out the taillight and signal lights but the headlight doesn’t come on so does the scooter need to be running for the headlight to work?
@toddrapp7904
3 жыл бұрын
Yes. The headlights only work when the scooter is running . Head light and tail light run off the rectifier (voltage regulator). Blinkers and brake light run off the battery
@neopositivity
3 жыл бұрын
When we first started fiddling with the scooter (it had been sitting for 2 years) my friend put the jumper cables on backwards (pos on neg). We saw smoke coming from between the front turn signal area (the cover was on). Can someone suggest a video to help me troubleshoot what happened? I can't find any burnt-out wire or anything looking suspicious. I have a multimeter but have no clue on how to use it for this application.
@toddrapp7904
3 жыл бұрын
Probably melted the group wire
@toddrapp7904
2 жыл бұрын
Check ground wire on ignition switch . Make sure it is not melted
@esolgatorres6403
Жыл бұрын
My 2019 wolf lucky sCooter 49cc just changed the turn signal relay it did burnt the wires.....
@lisacoleman2046
3 жыл бұрын
Need help with the throttle wires there is no we're to pull it in
@RedzicAnel
3 жыл бұрын
My right turn right signal doesnt work when engine is on. When is off it does work
@CenlaSelfDefenseConcepts
2 жыл бұрын
I have a tao tao 150 that's been sitting for awhile I had to replace the ignition switch because the people that gave it to us lost the keys I put a new battery on it and I can't get the lights to come on or the starter to cranks unless I jump the solenoid
@toddrapp7904
2 жыл бұрын
There is an online fuse connected to positive terminal . Make sure that is good. Also make sure the ignition switch wires match . Red/red Green to green, black to black, black/white to black/white. Sometimes they are not in the same position in the plug.
@deathcon6669
2 жыл бұрын
We're does the wires go form the brake my horn nothing comes on the wires are not all connected and can't find it no were
@toddrapp7904
Жыл бұрын
The head light and tail light are usually ran off the same circuit . The brake light is a totally different circuit . The rear bulb has two filaments . So one could be bad.
@seanmayo206
3 ай бұрын
I got stock front signals an after brake an signals on bike of gen v maddog
@GkorHerbalife
3 жыл бұрын
Hi.. I got a trouble with my headlights on my scouter.. The problem is that my lights are not strong enough... I have changed the light machine and the Regler and the battery problem not solved any suggestions?
@toddrapp7904
3 жыл бұрын
giwwrgos-svetlana there are two different bulbs made a 25 watt and a 35 watt. Make sure you try the 35/35 watt bulbs. Also the Xenon bulbs (blue) help as well
@toddrapp7904
3 жыл бұрын
Also make sure the socket is grounded good.. run a wire from the socket to the frame . See if the brightness goes up. The regulator should be putting out around 13.8-14.3 bolts at headlight..
@timcarlisle4990
Жыл бұрын
Why would break lights work and turn signals don't
@toddrapp7904
Жыл бұрын
Flasher
@Gothguitarist
2 жыл бұрын
Mines the opposite everything but the rear tail light works when I press the brakes the brake light turns on but without the brakes engaged the rear light stays dark any help?
@toddrapp7904
2 жыл бұрын
They work off of two different wires and power supplies . Brake light works off battery and brake switch . Tail light runs off of voltage regulator same as headlight . Motor has to be running to power tail lights . If not check wires at rear plug and socket
@Gothguitarist
2 жыл бұрын
@@toddrapp7904 the front light works everything but the taillight will work when bikes runing stays dark i dont want to have to rip apart my front cluster again haha
@zexmon2666
Ай бұрын
my scooter was in the rain and now no lights work
@vijayakrishnannair
2 жыл бұрын
Nice
@mrcleanisin
3 ай бұрын
You didn't ohm test the first brake switch to see if it was defective.
@AgeofReason
3 жыл бұрын
Hey buddy, found your clip by searching for "LED headlight upgrade flashers not working" I don't think this covers that, though, so please allow me to pick your brain, if you have knowledge please let me know, if not no offense taken. So I switched to the plug and play LED headlight from old lamp. The spread of the LED is great, but my flashers stopped working, simply staying "on/lit" solid. My flashers are still stock bulbs. Do you have any tips on what would cause this issue? If not, I didn't mean to waste anyone's time. Thanks for reading. Notes:horn and brake light still works. Unit reference from eBay: WinPower 6000K BA20D H6 COB LED Motorcycle Moped ATV Headlight Bulb Hi/Lo Lamp White USA
@toddrapp7904
3 жыл бұрын
The LED DO NOT DRAW ENOUGH POWER for flasher to work . You can use LED on front only or back only. . Or install a resistor then all will work. There are also special LED FLASHERS
@AgeofReason
3 жыл бұрын
@@toddrapp7904 so, in order to complete this modification, one should also upgrade the flashers system or install a resistor, yes? Did you do the flashers or resistor? I used LED only on front headlight bulb. Only. Nowhere else.
@toddrapp7904
3 жыл бұрын
@@AgeofReason , either one. The headlight has no effect on flashers . Nothing needs to be done to it . The blinkers work on a flasher system and there needs to be resistance for it to work .. Either way will work . The LED FLASHER IS EASIEST . Just a plug and play . Just make sure the plugs are the same . There a a few different plugs .
@AgeofReason
3 жыл бұрын
@@toddrapp7904 thank you. when I installed the light my flashers worked at first so I suspect a different short popped the flashers relay.
@toddrapp7904
3 жыл бұрын
@@AgeofReason unless you installed a new headlight with the blinkers in it , the headlight itself is usually on a different circuit .
@nicolewebb558
2 жыл бұрын
I need help with an ice bear three wheel moped the horn don't work and someone messed with the wiring and I don't have any knowledge on this type of moped
@toddrapp7904
2 жыл бұрын
Biggest thing is to determine if your horn is bad or wiring /button. Hook up a charged battery directly to the horn . If it Honks then your horn is good and you can direct attention to the switch . Or if you have a bolt Meter . Unplug horn and hook Leads to the horn wires. Push button . If you have 12 volts then button is good and you have a bad horn
@nicolewebb558
2 жыл бұрын
@@toddrapp7904Someone already been messing with it and cut the wires to short and tried jumping stuff and now the turn signal don't work and it keeps blowing fuses
@nicolewebb558
2 жыл бұрын
@@toddrapp7904 does it matter what wire goes where on the horn
@toddrapp7904
2 жыл бұрын
@@nicolewebb558 not really
@nicolewebb558
2 жыл бұрын
@@toddrapp7904 is the horn in sequence with the turn signal
@hot-shotlabel3212
2 жыл бұрын
What if my light gets broken everytime I put a new one on it
@toddrapp7904
2 жыл бұрын
Replace your voltage regulator . If it is bad it will blow the bulb once you rev it up .
@BigBoyJay_69
Жыл бұрын
Where is part 2?
@danylynn4028
4 жыл бұрын
Code is fire
@skitsafonic8510
4 жыл бұрын
Hi Todd rapp, I have an issue with my 125cc scooter and it's the headlights turning on and off while I'm riding at random times. Do you have any suggestions as to why this may be happening and any fixes that can help me? Many thanks dude, and great vid by the way
@toddrapp7904
4 жыл бұрын
Check the ground wire on the socket .
@toddrapp7904
3 жыл бұрын
SKITSAFONIC cold also be metal prongs on bottom of socket are barely touching the bulb. Simply remove bulb and push up prongs with your finger the reinstall bulb
@petercriscuolo103
Жыл бұрын
That's why the prices on line are so low.
@nomansland5739
3 жыл бұрын
im dizzy now.. thx
@jodyholcomb3738
Жыл бұрын
It's a fuse
@jodyholcomb3738
Жыл бұрын
What do you do for one if horn works an lights working but won't start. I've got one bin try to fig it out four 2 years now can any one help me
@jodyholcomb3738
Жыл бұрын
I fix it
@jodyholcomb3738
Жыл бұрын
Some got fuses to might be a fuse
@handyhawaiian
2 жыл бұрын
I have a 2013 tao tao my blinker wont blink just stay solid when turned on then turn off when u out the switch back to center i replaced the relay n that didn’t help
@toddrapp7904
Жыл бұрын
There is a flasher that I would replace first . Second , if the bulb is bad on the other blinker on the same side it may not blink . For instance , if the front blinker comes on but doesn’t flash, check rear build to make sure it is good
@Hari-888
2 жыл бұрын
Thank you, I learned something today
@robertsavell17
2 жыл бұрын
You are not right I got mine from a dealer they have the same issue.
@toddrapp7904
2 жыл бұрын
I am a dealer and have been dealing with the Chinese market for 13 years. They have gotten better but still have to check everything before they hit the showroom .
@ManuelGutierrez-be1ci
3 жыл бұрын
I bought my Yamaha vino 50cc as a project and I need to figure out the blinker wires and the headlight and taillight but I can’t afford the oem stuff. What’s your suggestion on diy?
@toddrapp7904
3 жыл бұрын
Unfortunately YAMAHA STUFF IS UNIQUE. Main thinking is to determine if it getting power . Some Vinos use a tiny battery that sucks . And is expensive to replace .
Пікірлер: 105