yup, so I figured this out last night after some trial/error. The bushings are mostly round with a flat side that has to line up with the gear case ends when they are pounded in. If not lined up it will tighten and look correct but causes the impeller to not turn easily. This was masked by the fact that I had to clean the grease off to see this. Works great now. Thanks!
@eddielawnequipment6094
4 жыл бұрын
Thanks for a wonderful video I’m a big fan
@harmonicsl
13 жыл бұрын
dony, that gear you replaced looked like soft material, am i right? if so why? you are the only repair person i watch. i think you are superior.
@turkmyster99
Жыл бұрын
Your videos are a great help with fixing a lot of Snowblowers and lawnmowers you are my go to guy for video help. i have the same snowblower going to rebuild the gear box plus i like to change the impeller bearing at the same time i see you just pack it with more grease but i like to replace it. do you happen to know the part # for the bearing thank you i would appreciated any help you can give.
@donyboy73
13 жыл бұрын
@harmonicsl Yes I think it is brass or bronze, thank you for the nice comment
@johnheidmann1616
7 жыл бұрын
Nice careful work and good production quality. Well done.
@donyboy73
7 жыл бұрын
thanks John
@donyboy73
13 жыл бұрын
@AllenTrucks i usually keep it on because i go in and out a lot
@donyboy73
12 жыл бұрын
@grego10r that should be ok, i usually use a 00 grease
@goodvids6161
6 жыл бұрын
have a 1989 noma 8hp 24". replaced auger gear. per your video.. putting it back together, with gear housing bolts not completely snugged down the auger shaft turns freely, but when torqued to only 5ft Lbs. the auger shaft turns very hard. took it back apart 6 times, cant find what's binding.
@ccalzeti
11 жыл бұрын
Thanks for the great video. I installed a new impeller and the shaft turns fine until I tighten down the screws... it moves very smoothly when the screws are lose but takes a lot of effort to turn after they are tightened down. Is this normal? Just don't want to get back together and have to take apart again. Thanks!
@mignolan
10 жыл бұрын
Terrific work! I've been working on an MTD snowthrower that had a cracked auger gear box, and after removing the auger assembly from the overall thrower box, I found four thin, large washers, slightly greased, on the floor. Any ideas? : ) I also have two bushings -- identical. They don't seem to fit anywhere. Ho-hum. Any help would be appreciated!
@legogamer999
10 жыл бұрын
very funny question so should you be able to hold the augers and the impeller freely spins? Mine did that before now it doesn't could it need more grease? I didn't refill it since it seemed okay and the gear was actually fine. It's a 1998-1999 5/22 Craftsman low use 1-2 times per year. It spins as little as it did in the beginning of this video. The first part helped me take it apart.
@donyboy73
13 жыл бұрын
@redbarn713 thanks very much!
@donyboy73
11 жыл бұрын
you mean the gear box?
@jimschowe2770
7 жыл бұрын
The little half moon shaped item is a woodruff KEY that fits into a 'keyway' Kind of small correction but say what you mean please.
@donyboy73
13 жыл бұрын
@colbycous01 not quite sure why the collar is there
@macspud28
8 жыл бұрын
Just to correct you on your use of keyway, what you are calling a keyway is actually a key (woodruff key in this instance). The keyways are the slots cut into the shafts, gear cog and pulley. I regularly hear people wrongly calling keys keyways so it seems to be a common mistake.
@donyboy73
8 жыл бұрын
+macspud28 yes thanks, I realized that after
@ArchersPlace
7 жыл бұрын
Hey @donyboy73 I have a MTD yard machine that I just swapped out the worm gear like you just did, but my auger has 4 separate blades with spacers. Does it matter how I assemble them back on the bar, or as long as the align with the pin holes and spin without complications, it is fine?
@donyboy73
13 жыл бұрын
@MultiKhaz lol, hopefully u got it for free?
@johnheidmann1616
7 жыл бұрын
The key way is is the machined slot in the shaft, and the woodruff key is the key.
@donyboy73
7 жыл бұрын
lol, thanks sometimes I get it mixed up
@Razorrebel1
8 жыл бұрын
A fully threaded shear bolt for application mounted on a axle is bad business. Is it the actual OEM-part?
@donyboy73
8 жыл бұрын
+Razorrebel1 this is oem bolt on Noma and Murray snowblowers
@richardracicot1982
11 жыл бұрын
hey guys does anyone know who makes Duramark brand of snow blower i need parts for it and i cant find any info on this brand i bought it used so i have no paper work its DURAMARK 2 stage 523 with a 5hp tecumseh motor . need help Ottawa Canada thanks
@donyboy73
13 жыл бұрын
@zigZag776 thanks, lol
@donyboy73
11 жыл бұрын
send me pics
@donyboy73
13 жыл бұрын
@kimokanka yep on a secret mission for the russians
Пікірлер: 31