Thank you so much for this video, and the derailed breakdown of this device. It really helped me out on having to figure out which wire goes where.
@604smit
5 жыл бұрын
thank again Robojax, Just one week ago received this meter from China and now you have this review, timing could not be better😊
@robojax
5 жыл бұрын
You are welcome Leo. I am glad you found it useful.
@BrianKarmo
3 жыл бұрын
Thank you kind sir for your very specific informative directions. Did not come with any instructions that also greatly appreciated or I would have been blind
@robojax
3 жыл бұрын
You are very welcome. Please subscribe. I appreciate it and helps my channel grow. Thank you
@moking8095
6 ай бұрын
Hi All I have spent a little time on this problem and finally twigged that the tiny unmarked X in thick red wire was in fact the most important item, namely the load. This all now makes sense.
@ticktock8751
4 жыл бұрын
you can wire the meter off the same voltage supply, what i am trying to say is you don't need another power supply to run the meter. its very easy to do.
@robojax
4 жыл бұрын
If you measure the current for a source less than 5V, the display with turn OFF. You need separate power to keep this working. Thank you.
@ticktock8751
4 жыл бұрын
@@robojax i am not going to go lower then about 7v so its ok
@robojax
4 жыл бұрын
Yes.
@woxnerw
3 жыл бұрын
5 - STARS.. Thank You..
@robojax
3 жыл бұрын
You are welcome. Please subscribe as well.
@tonysfun
5 жыл бұрын
Very nicely done my friend!
@robojax
5 жыл бұрын
thank you dear friend.
@CreativeThings550
3 ай бұрын
Assalamualaikum sir, I am inspired by your educational and knowledge based videos from chittagong city of Bangladesh, also I can learn about electronics from experienced people like you, Allah Hafez.
@vazeel23
4 жыл бұрын
greet, you helped me out, without blowing up this little piece :-D !
@robojax
4 жыл бұрын
Good to hear that.
@LegacyMicro
4 жыл бұрын
Thanks for the info. You got lucky. I bought 4 of them and the current meter jumps around on all of them. Your meter seems stable. The Peacefair PZEM-031 is a better built and more accurate module IMO... Keep up the good work. You make great tutorials!
@robojax
4 жыл бұрын
You are welcome. Thank you for sharing. Here is the search result with keyword Power Meter : kzitem.info/rock/kcBSig_Iu4ZnAIeCeG1TVgsearch?query=power+meter
@charlesantonio8867
3 жыл бұрын
you all probably dont give a shit but does anyone know a trick to log back into an Instagram account? I was dumb forgot the login password. I would love any assistance you can offer me.
@dominikzaire3020
3 жыл бұрын
@Charles Antonio Instablaster :)
@charlesantonio8867
3 жыл бұрын
@Dominik Zaire thanks so much for your reply. I got to the site through google and im in the hacking process now. Seems to take quite some time so I will reply here later when my account password hopefully is recovered.
@charlesantonio8867
3 жыл бұрын
@Dominik Zaire It did the trick and I actually got access to my account again. I'm so happy! Thanks so much you really help me out!
@theprepperfrog167
3 жыл бұрын
Thank you, sir.
@cristiangonzalez1707
4 жыл бұрын
Good work, thanks for the info my friend.
@robojax
4 жыл бұрын
No problem 👍
@tuxillo
4 жыл бұрын
Thanks.
@robojax
4 жыл бұрын
You are welcome.
@moking8095
6 ай бұрын
You show a stylized battery with the thick red and the thick going respectively to positive and negative. Unfortunately, the thick red and thick black go straight to the shunt which would soon short the battery out and burn out the shunt. I think you need to revise your diagrams.
@javiev
3 жыл бұрын
muchas gracias..
@robojax
3 жыл бұрын
no problem.
@ibzanypava9863
5 жыл бұрын
Hello, I thank you for sharing, I have achieved this instrument but I have not managed to make it work well I have seen the video but I do not understand some words because I do not speak English and I would like to ask you the favor if you can give me indications of the written connections, either in English , to translate them into Spanish. you have a subscriber you are the only one who gives explanations. Very thankful.
@robojax
5 жыл бұрын
You are welcome. snipboard.io/x80ryg.jpg
@Pulverrostmannen
10 ай бұрын
I come to the conclusion these devices are extremely sensitive to ripple in the voltage, it just start to jump around in the shown values very easily, If the voltage and current is clean they show fine. otherwise they are pretty nice. I think the issue is that they have too high refresh rate
@janimaabdulmalik6196
15 күн бұрын
Brother how can connect this watt meter into solar set-up
@madhukeshnp
5 жыл бұрын
Sorry to say... The volume is way too low. This is not the first time. Please change your mic or boost it up in the software.
@xeroxene
5 жыл бұрын
Robojax, I can hear and understand you perfectly. I had to turn the volume up 5% compared to the previous video I was watching. I am watching this on a television in a noisy room. Hello from Australia!
@robojax
4 жыл бұрын
MADHUKESH, I just discovered your comment. I have made some changes. Thank you for the tip.
@robojax
4 жыл бұрын
Hi Alpha, I missed your comment. Now KZitem have new tools that shows all comments I have not replied. Thank you . Hello from Canada.
@NsndoBrasil
Жыл бұрын
Can I use a 12Vac output with diodes and capacitor to make a 12 volt source with CI LM7812 to power the lighting of this Module (Deek-Robot Shield Mod.BL-01)? Note that this derivation is from the same transformer that I made the variable source from 0V to 50V!
@johnstone-gh9nj
Жыл бұрын
Is the Deek made to control power from Solar Panels to Heat Water Element in Cyclinder. Will the element Arc ?.
@yogeshitaliya473
5 жыл бұрын
Nice one sir
@robojax
5 жыл бұрын
Thanks.
@laurikranz3469
3 жыл бұрын
Obrigado
@robojax
3 жыл бұрын
de nada.
@tomb2623
3 жыл бұрын
Good video! Is it accurate in 0.5v-5v range too ?
@robojax
3 жыл бұрын
Yes it is . But for very accurate reading you should get something that measures up to 10v or 20v
@GladstonAlmeida8667
3 жыл бұрын
Plz do video how to connect this meter to solar panels
@robojax
3 жыл бұрын
This is how it is done. I mentioned the load which is your load. I mention power supply which is your solar panel.
@jhonmcheaven3205
Жыл бұрын
If you put that in motorcycle where should you put the wire in load that all load will be calculate?
@robojax
Жыл бұрын
I have shown in video two things 1-Power supply 2-Load. so whatever I said, for you 1-Battery and the 2-motorcycle is your load. Just follow that
@wachidintegal5180
4 жыл бұрын
Hii... what can be replaced with a external shunt ....if you want a higher range measurement? Thanks sir
@robojax
4 жыл бұрын
Hi, here is using shunt with Arduino to measure up to 500A kzitem.info/news/bejne/2X6bn4aIiol-dYI or use a module with shunt kzitem.info/news/bejne/1Z2ky4JooayDmGU
@sec.0991
8 ай бұрын
can it measure in the range of millie watts ?
@robojax
8 ай бұрын
All features have been explained d shown. Please watch and get answer.
@Maersky-747
5 жыл бұрын
I have the BL-02. What is the supply voltage/current needed to power the device? Can the device be connected to a 12v car battery and measure the voltage/current of the battery?
@robojax
5 жыл бұрын
this device can be connected to Car battery to measure the voltage. It can measure only 10A max. When you start the car, it uses about 400A or more if larger car. So this can't measure it. Of course if you connect a device that uses 10A or less, it can measure it in car too. What is B02? I did not find it
@Maersky-747
5 жыл бұрын
@@robojax The BL-02 is the same Ampere Power Meter you used in the review. If you look on the back of the circuit board you'll see 'BL-02'. That is the model. I have a device that draws 12v @350 mAh from a car battery. When the car battery is fully charged, I want to use my BL-02 to monitor the Voltage and power consumption for a month or longer, until the battery is flat. Can the Meter be connected directly to the battery or does it need a small load in place?
@robojax
5 жыл бұрын
Thank you for telling me the model. I will have to look at it. My answer is the same as above with addition, to measure Power, you need to measure the current.
@edinfific2576
4 жыл бұрын
I have read that the device itself uses under 15mA. The voltage is apparently 7-12V, but I would say that it can go at least up to 15V (it would have to go that high to work with a car battery). UPDATE: I have checked mine and the supply current is 10mA. The specs say 7-12V supply, elsewhere I've seen warnings about not going over 13V, but it ran fine for a month or two (until I replaced it with a better power meter; it didn't fail) on my battery which often got to 13.5V and very rarely up to around 14.4V.
@thagoson
3 жыл бұрын
The connection of the DC 0-50V (input or output source?) as shown in the diagram is not correct since these two terminals which is connected with the red and black wires from this source is shorted together with the wire shunt and cause short circuit to this DC 0-50V unless the black cross in the circle is to indicate the red wire is not used, if so then it should not be in the diagram in the first place.
@thagoson
3 жыл бұрын
Apologize for my above comment on the diagram that I've got the image from the net. The info in your video does now make everything clear up now. Thanks for your good work.
@robojax
3 жыл бұрын
no worries. you are welcome. You can edit comment by clicking on the 3 dots that shows for each comment. good luck.
@beastcode2865
2 жыл бұрын
Can you use external shunt to make the amp capacity higher?
@robojax
2 жыл бұрын
No you can't. you would need different meter. see this video kzitem.info/news/bejne/rqOu3WuKa2uLaaA
@dj_sorra8605
Жыл бұрын
Can I put a 24v adapter with 6Ah and 100w instead of the 0-50v battery?
@robojax
Жыл бұрын
of course you can.
@dj_sorra8605
Жыл бұрын
RESPECT🙋♂️
@praias50
Жыл бұрын
Boa noite tem esses vídeos em português Brasil
@robojax
Жыл бұрын
Sorry I speak English and Farsi.
@paolomichielin4849
2 жыл бұрын
Una domanda. Dove c'e' la crocetta a sx, cosa bisogna mettere? Una lampadina? Se si', da quanti volt? Grazie per una eventuale risposta?
@robojax
2 жыл бұрын
Ciao, mi dispiace aver visto il video e non ho capito cosa croce. per favore menziona l'ora come le 3:50, quindi la guardo. Grazie
@paolomichielin4849
2 жыл бұрын
Il carico da collegare al voltmetro amperometro come deve essere? Intendo il filo bianco!
@Bergwacht
4 жыл бұрын
Can I use this measuring device on my car? Supply voltage is described with DC 7-12V. But if the car's engine is running, there are 13.7 to 14.7Volts, can i use this wile driving?
@robojax
4 жыл бұрын
maximum voltage is 12V. you may have to risk and test it to see if it dies or not.
@Bergwacht
4 жыл бұрын
@@robojax more worse... I cooked my pv module with that thing lol tomorrow i will buy a bigger 320wh one.
@Bergwacht
4 жыл бұрын
@@robojax If I cook one of these it doesn't matter, I accidentally bought 5^^
@robojax
4 жыл бұрын
Yes. so what happened did it burn or not?
@Bergwacht
4 жыл бұрын
@@robojax there was a cloud of smoke. I think I didn't understand the instructions correctly (as shown here) When I put it like the one in the pictures, there was a spark, there was smoke and my solar system was done. now i have bought a new solar cell, but the pain runs deep - these things are expensive. In the circuit diagram of banggood, the 2 cables are brought together, the ampere test lead and the volt test lead. But when I closed it together, my solar panel burned out and the fuse on my expensive victron charge controller. So iam lucky now that i dont need a new 100€controller.
@hipower1059
4 жыл бұрын
Please Why display isn't clear ??? Or it have weak light ???
@robojax
4 жыл бұрын
I will reply to all Subscriber's 🔔 questions. So make sure to Subscribe.😊
@groovyone5492
4 жыл бұрын
The white wire should be connected to the load side +...not the supply side +
@robojax
4 жыл бұрын
make sure to follow what I have shown. I have already burned ONE of these.
@egeotomasyon
5 жыл бұрын
Power (watt) indication is wrong ! 9:08 Voltage 21.8V, Current 10A, P must be 218 Watt. But indicator show 214 Watt !
@robojax
5 жыл бұрын
The device has refresh rate. It doesn't refresh quickly. It takes a little time. Also 5% error is normal.
@Viruslinux
4 жыл бұрын
Bagaimana cara menaikan amperenya?
@robojax
4 жыл бұрын
Tidak memungkinkan. Anda harus menggunakan modul lain.
@101Gabriel_M.
5 жыл бұрын
This wire diagram/explaining totally fucked up... If you zoom back to a littlebit wider view angle, maybe we see and understand something from this mess...
@robojax
5 жыл бұрын
where? please point to the time like 2:30
@awesomed007
4 жыл бұрын
i agree, this video was too frustrating and laborious for me. Zoom out and show connections to load etc properly
@awesomed007
4 жыл бұрын
kzitem.info/news/bejne/sa53v4mPk5GWlHo ... this was super wiring explanation
@Tomas0088
4 жыл бұрын
طالما انك عربي فمن باب اولى ان تتكلم وتشرح بالعربية ليفهمك بنو عمومتك العرب حيث لا يوجد شرح لهذا الجهاز باللغة العربية اما المقاطع الاجنبية فهي كثيرة جدآ و انا متأكد انه عند شرحك بالعربية ستجد متابعين لك كثيرين من العرب خصوصأ ان الشرح يتضمن مخطط توضيحي يبين مراحل صنع الجهاز
@robojax
4 жыл бұрын
السلام عليكم ، شكرا لك على تعليقك. أنا فارسي كندي من خراسان الكبير من أرض الإمام البخاري ، إمام مسلم .... خراسان هو الآن أفغانستان وشعب أفغانستان ليس أفغانيا. أتكلم الفارسية وأنا في طور تعلم اللغة العربية إن شاء الله. بسبب تعليقك ، قمتُ بترجمة العنوان الفرعي باللغة الإنجليزية واستخدمت Google لترجمته إلى العربية و 30 لغة أخرى. يرجى مشاهدة الفيديو الآن بالعنوان والوصف باللغة العربية إذا قمت بضبط لغة الكمبيوتر أو الهاتف على اللغة العربية. بالسلام
@Tomas0088
4 жыл бұрын
@@robojax شكرآ جزيل لك اخي صاحب القناة على سرعة تجاوبك مع طلبي واتمنى لك التوفيق بتعلم اللغة العربية للغة القران الكريم والنجاح والتوفيق و الانتشار الى قناتك المفيدة للمبتدئين وحتى المحترفين
@robojax
4 жыл бұрын
مرحبا بك. أنا أتعلم العربية وفي يوم من الأيام سأقوم بعمل مقاطع فيديو باللغة العربية في شاء الله.
@Tomas0088
4 жыл бұрын
@@robojax ان امكن تصغير حجم خط الترجمة لان حجم الخط الكبير يحجب الرؤيا لمشاهدة الفيديو
@robojax
3 жыл бұрын
لا يمكنني تغيير نص الترجمة. ربما يضيف KZitem مثل هذه الميزات حتى يغيرها المستخدم. في مقاطع الفيديو الخاصة بي في المستقبل ، سأحاول عدم إظهار أي شيء مهم في المناطق التي يتم فيها عرض الترجمة.
@jeffbluejets2626
11 ай бұрын
Probably makes little difference as it is series, but your circuit diagram for the current is different from your physical hook-up....thing is, mistakes like this can make it difficult for beginners. Suggest you double check before posting.
@robojax
11 ай бұрын
1000s of people learned from this. you skipped the video. please watch again. it can't be better than this. believe me. Watch again.
@NsndoBrasil
Жыл бұрын
Can I use a 12Vac output with diodes and capacitor to make a 12 volt source with CI LM7812 to power the lighting of this Module (Deek-Robot Shield Mod.BL-01)? Note that this derivation is from the same transformer that I made the variable source from 0V to 50V!
Пікірлер: 102