Videos a lil hard to follow at times but still made it possible for me to get the job done. So thank you moccasin marine!
@radiogetsemaniusa6942
2 жыл бұрын
My engine has of water in the oil and I open it up and I put in your head gasket on it but now it doesn't start
@isaacgriswold3566
Жыл бұрын
When showing us the timing marks what degree is your timing light set at? Before you connect the shunt tool to go in base timing mode are you setting timing light to 17 degrees, then setting it back to 0 when you go into base timing mode?
@moccasinmarine
Жыл бұрын
My timing light is not the digital kind I can set. Set your light to zero degrees and then read the timing marks on the balancer and the timing cover.
@isaacgriswold3566
Жыл бұрын
ok, but in theory at 600rpm idle after going into base timing mode to confirm your timing tab is slightly before TDC, you can set your digital timing light to 17 degrees, since the timing tab marks do no go up that high. which should show the timing mark approximately 1 inch past TDC.
@johnyellowman9900
Жыл бұрын
I upgraded my ‘86 SeaRay Seville cuddy cabin 4.3 with a similar system bought through southwest performance…will that 1degree be also what I need mines at? The factory is 8 degree
@moccasinmarine
Жыл бұрын
It depends on what module they included in the system. I’ve never bought their products so I don’t know what kind of module they use. I personally will use nothing but Delco D1965A modules. I’ve had numerous problems with aftermarket modules.
@bradsheets2169
2 жыл бұрын
Question when plugging in the shunt tool is my timing supposed to move. Mine does not.
@moccasinmarine
2 жыл бұрын
Yes the engine will slow down with shunt tool connected to 12 volts
@bradsheets2169
2 жыл бұрын
@@moccasinmarine Ok thank you. Sierra is providing me with a replacement ignition module.
@War1050
2 жыл бұрын
What should the new base timing be if you do this conversion on a 2002 5.0L Mercruiser? The air cleaner on it says the same 10 degrees BTDC like this one but I'm having trouble finding anything for the new base timing.
@moccasinmarine
2 жыл бұрын
Go to the end of Part 6 video. There is a chart that gives the base timing for all size engines. The 5.0 just happens to be 10 BTDC just like the Mercruiser Thunderbolt so in your case the base timing is 10 BTDC.
@War1050
2 жыл бұрын
@@moccasinmarine Thanks for the info. I missed that chart in the video somehow but had come across that spec sheet at some point and just wanted to verify it was correct.
@josephharris9973
Жыл бұрын
Do you have an email? I have some additional questions/ seeking guidance. I installed the ignition system over the weekend and my boat fired for about 2 seconds and then died. Getting fuel, timing was set correctly, and I have no idea where to go from there.
@moccasinmarine
Жыл бұрын
What ignition system? Mine or another?
@josephharris9973
Жыл бұрын
@@moccasinmarine delco est. I ordered it from southwest performance
@moccasinmarine
Жыл бұрын
@@josephharris9973 that’s your problem. forums.iboats.com/threads/video-what-the-heck-is-this-1999-volvo-4-3-gl-2-bbl-holley-carbureted-ets-ignition.764570/page-2#post-5842932 Post #22. They sold the guy an automotive module. The modules are not GM. That’s all I will say.
@josephharris9973
Жыл бұрын
@@moccasinmarine do you have a link to yours? I’ll pull this one out and send it back. It’s stamped D1895 which is the marine version, but after reading some of those remarks, it’s best to send it back and order from somewhere else
@moccasinmarine
Жыл бұрын
D1965A is the marine version. Go to this video and read description. My email is there to take this private. kzitem.info/news/bejne/pp94mnpnj2mKno4
Пікірлер: 20