Just stumbled on this video and you’re right because people don’t tell you this, I figured this out on my own and it definitely helps. Good stuff
@thebuzzbristol
4 жыл бұрын
Jay Sal thanks man
@kalebgrosso1185
8 ай бұрын
Same here. It's taken years lmao.
@classikclips
3 жыл бұрын
What about the contact points where the clip cord connects to the machine i thought that would have some effect or build up there that needs to be maintained where it needs to be cleaned as well.
@inkslang2101
2 жыл бұрын
Where can I find the black machine? I really love it
@mtm4505
4 жыл бұрын
Thanks!!✨
@thebuzzbristol
4 жыл бұрын
MTM Our pleasure 🙏
@ivanmendoza8457
2 жыл бұрын
Put a layer of wax on the frame Renaissance wax specifically if you live in a coastal region and theirs alot salt in air this will prolong the life of your machine
@captainleonardodivichi295
Жыл бұрын
I just got a maintenance kit for my guns . I’m going to redo them today . I’ve got an issue with the needle not going in and out the tube smoothly and the ink isn’t running down to the tip of the needle through the tube as well . I don’t even have a rubber band around the base of the needle . All that’s on it is a rubber grommet . If I do put a rubber band around the core coil and around the needle it has a hard time running even when I’m at 10.5 on me box . I’ve got two other tattoo guns on the way through the mail to me should be here on the 17th of this month 2023 . We shall see .
@thebuzzbristol
Жыл бұрын
If you have IG or Tik Tok, send us a video of the whole set up. Hard to diagnose the problem without seeing how it’s all running @thebuzzbristol on IG or @thebuzztattoo on Tik Tok
@Jaydawgydawg99
3 жыл бұрын
Amazing video! Thanks! - i got a question tho, i Just got my first coil machine but i have a problem where when i have rubber bands on the machine/ needle to keep it stable the machine gets really Weak.. Low or high voltage does not fix the problem.. Any ideas why this happens? :-)
@thebuzzbristol
3 жыл бұрын
Hey, cool common problem. The band will be too tight stopping the needle from moving freely. Try different bands til one fits nicely, a band doesn’t need to be tight to keep the needle steady. If the machine runs nicely without a band then it’ll be a simple issue. Let us know if it doesn’t work, we will try something else
@sooyeongmin3482
2 жыл бұрын
my machine still doesn’t work i tried every problem fixing its fresh outta the box but i still can’t run it
@Bentlybow
4 жыл бұрын
Use mothers polish to clean your contact screw! Don’t sand them down lol eventually you won’t have a contact screw.
@Denka187
3 жыл бұрын
you have any tips for the frame , seem to somehow always end up with tubes dont fit after a while no matter how lose or tight i lock the tubes , ending up with bending up the frame so a tube can fit in there - always happens with the ones where he whole frame open and close like your green one there
@thebuzzbristol
3 жыл бұрын
Sometimes it’s actually your tubes that are bending. If you’re using metal grips that will bend more and more over time to the point that your machine clamp won’t hold them properly. Otherwise it could be a screw in your clamp
@Denka187
3 жыл бұрын
@@thebuzzbristol disposable only , the frame kinda locks so hard that you have to bend it open after a while and that destroys the whole frame . guess its all the vibrations aswell becuse sometimes i lock it very gental but it still sits like a rock after a couple hours . its to bad becuse the machines are useless after that , crank up the frame everytime bends the whole thing .guess machines with Guillotine Vice is better options ?
@thebuzzbristol
3 жыл бұрын
@@Denka187 I’ve had the same problems before and changed my screw and bent that part of the frame slightly, something is wrap something around the top of my tube to give the clamp something to hold onto. Hope that helps
@Denka187
3 жыл бұрын
@@thebuzzbristol sounds good , some griptape maybe do the trick , thankx for the time and help man .
@lukedorrington7455
3 жыл бұрын
When I have my coil machine set it runs really nice 130cps at 50 duty but if I touch the arm bar to check it the needle almist fully retracts into the tip, I have to hang the needles quite far out to achieve proper depth, how can I fix this?
@thebuzzbristol
3 жыл бұрын
How is it when you’re tattooing? Try running the machine to no needle. Leave your finger under the armature bar to create some resistance and see if it runs consistently or if it’s starts to struggle. Even a nice soft machine should run smooth with resistance, it could be that your machine isn’t a smooth runner. Maybe there’s some dirt build up in between the armature bar and the coils? If it runs smooth with no needle, then it could be the needle hitting the inside of the grip?
@lukedorrington7455
3 жыл бұрын
I tested it on some practice skin and it runs fine just with that much hang I was worried about going to deep or will that not happen as it retracts so far anyway? It's hanging out about 4mm and retracts right back to around 2mm, if I adjust it so the needles flush with the top it just goes right back inside
@kellydollie6435
3 жыл бұрын
Wht can i do
@johnwallace3215
4 жыл бұрын
Hey when I push down on my foot pedal, the light flashes on and off evreytime the needle goes down and it goes up down 1 every 2 seconds
@thebuzzbristol
4 жыл бұрын
Hey, ok, if you flick the armature bar does it start running normally again? Some times there’s a bad connection somewhere in the circuit, maybe dirt build up in the machine etc that is stopping it running consistently. Sometimes a foot pedal or power supply light will stay on all the time, but sometimes like in your case it will only come on when the machine is running, as the armature bar hits the coil it start the circuit running again, so a dirt build up will block the flow. If that doesn’t work message back
@johnwallace3215
4 жыл бұрын
@@thebuzzbristol wth it worked, I've been trying to fix it for awhile but yes it's working now👍🤙
@thebuzzbristol
4 жыл бұрын
Great!
@merdiexbatucan5126
3 жыл бұрын
@@johnwallace3215 did u just cleaned it up and sanding the contact screw and front spring?
@kellydollie6435
3 жыл бұрын
Hi my amature bar is touching the coil i tried a lower voltage but then it jst vibrate nd does nothing
@thebuzzbristol
3 жыл бұрын
Hey, do you mean it’s stuck on the coil? You can send us some videos to our Instagram DM if it’s easier than explaining @CrooksTattooStudio
Пікірлер: 30