Just bought a boat with this motor. Now I feel confident to do the carbs.. THANKS
@danielmeecham464
2 жыл бұрын
Well done sir! Thanks for sharing. I've got an identical motor that's idling just a little rough. Mine motor is a 1992. I just did a complete electrical parts overhaul. I was apprehensive about digging into the fuel system, but thanks to your video, now I'll remove and clean the carburetors.
@officialWWM
Жыл бұрын
How did it work out for you?
@danielmeecham464
9 ай бұрын
It worked out great! I simply focused on the basics: fuel, air, spark. I just cleaned all the parts, an replaced ones in doubt.@@officialWWM
@CTRadventures
3 ай бұрын
Thanks for this video! We just bought an 88 ranger 393v that came w a 6 cylinder 87 Johnson 150. The oil injectors removed to run 2 stroke. This is my first bass boat and power engine, so I'm trying to learn as much as possible. Again I'm completely new to motors, sometimes she seems she's a little rough on idle so I thought, hmm maybe the carbs need cleaned
@officialWWM
Жыл бұрын
Thanks mate. Very detailed and extremely helpful! Cheers from Tasmania.
@colvinau1403
Жыл бұрын
Mans did this shit one handed
@emmettjones1961
3 жыл бұрын
Excellent Great video
@travelguy1564
2 жыл бұрын
Did you take off the oil pump system and just convert it to pre mix? If so, how did you do it?
@7tosand
13 күн бұрын
I didn’t see any gaskets when you took the carb apart, or on the intake manifold. We’re there any gaskets?
@jordansyrus8900
2 жыл бұрын
Hey bud do you know if you can buy cowling covers for a 1994 50 hp mercury I’m thinking about buying one but wanted to know if you could buy this part still
@FullThrottleGarage69
2 жыл бұрын
very good video
@zeeduk
3 жыл бұрын
Will want to clean each intake hole behind the carb before putting the carbs back on as well but great jobs showing how easy it can be.
@outboardsandtoys8413
3 жыл бұрын
I agree I have seen screws and other stuff in the reeds
@simonandersson8197
3 жыл бұрын
what does the holes in the back of the carbs? i have a mercury 50hp 2 stroke, and it is more fuel flow on one carb? and bogging when i accelerate. from sweden not very good english
@simonandersson8197
3 жыл бұрын
done carb clean 13 times now and changed membran
@jamescraig8601
Жыл бұрын
Change your filters
@Deon-ot2vi
2 ай бұрын
Thanks for the great video. Helped me out.
@savagenomore
3 жыл бұрын
that float is adjustable, just bend the little metal tab the needle hangs on
@outboardsandtoys8413
3 жыл бұрын
You are correct I did not notice it when I done it
@quranwithurdutranslation7199
3 жыл бұрын
Great work... Just subscribed your channel.... From : 71 Satisfaction Inn
@giloquendo
Жыл бұрын
Great video question does that high speed jet has a hole or is it sealed
@officialWWM
Жыл бұрын
It has a hole. That’s how the fuel goes in!
@kingpondah990
3 жыл бұрын
What did you use to clean the carbs?
@outboardsandtoys8413
3 жыл бұрын
I used a ultrasonic cleaner I got from harbor freight and the used air to blow through the journals
@bumpskier88
2 жыл бұрын
hey , is it not necessary to use a gasket when remounting the carbs?
@outboardsandtoys8413
2 жыл бұрын
Yes there is a gasket behind the carbs on the intake alot of times it is stuck to the carb or on the intake may not be able to see it on the video
@ngbay160
2 жыл бұрын
Took my boat out today. Idles fine and starts right up, BUT once i open it up all the way it will run but it acts like it fights for gas? Dirty carb? Fuel is fresh and the gas tank is new
@outboardsandtoys8413
2 жыл бұрын
I would say so starving for fuel sounds like the high speed jets
@outboardsandtoys8413
2 жыл бұрын
Easiest way I know how to tell is choke it when trying to get on plane if it increases rpm for a few seconds most likely it's the jets
@Eric-fq5wx
3 жыл бұрын
Is there an idle jet?
@outboardsandtoys8413
3 жыл бұрын
Yes I did not go into that on this video cause u have to set the screws on each carb they can be very tricky to adjust if u dont get it right it will Ethier be lean or to rich the best way to set low speed is with gauges
@mylotmarshall8885
2 жыл бұрын
What year is that motor?
@colvinau1403
Жыл бұрын
90s probs
@1988aweb
Жыл бұрын
Are there no gaskets between motor and carbs?
@jamescraig8601
Жыл бұрын
Mine only has two carbs.
@tnybo13
2 жыл бұрын
Half a job, basically if you're not cleaning the whole system a waist of time.
@outboardsandtoys8413
2 жыл бұрын
really where is your video and whats half the job also this motor has been doing perfect on this half a job waste of time
Пікірлер: 39