Such a Beautiful Bed my friend. Looks very nice. You did an amazing job. Very impressed with your talents.
@IronSlugs_garage
2 ай бұрын
Thank you Rick!
@WhiskeyDents
3 ай бұрын
I’m so impressed with that bed. Nice work
@IronSlugs_garage
3 ай бұрын
Thank you, I appreciate it! I’m proud how well the floor turned out.
@RCXBuildsIt
3 ай бұрын
That bed floor is too cool 🇺🇸 Nice work
@IronSlugs_garage
3 ай бұрын
Thank you!
@jeffbrook6054
3 ай бұрын
Beautiful work !!!!
@IronSlugs_garage
3 ай бұрын
Thank you!
@jeffbrook6054
3 ай бұрын
@@IronSlugs_garage I wish I thought of doing that to my bed. Hat's off to you. Keep it rock'n
@IronSlugs_garage
3 ай бұрын
@@jeffbrook6054 your bed looks great, lots of creativity. I can’t take full credit for this one haha. A buddy sent me a picture of this old Chevy that had a burnt wood American flag on the bed and I thought it looked amazing so I knew I had to do a flag on my bed.
@Thelegendking-yj4bm
3 ай бұрын
Was just going to comment on fuel neck. Then i hear one last thing i forgot.
@IronSlugs_garage
3 ай бұрын
Hahah yup! I hope it helped. The Vic fuel neck will slide right out and I believe I cut my filler tube at the end of the taper. I cut it too short the first time and had to weld it back together and do it again haha.
@Thelegendking-yj4bm
2 ай бұрын
@IronSlugs_garage when you cut the fuel neck any tips on not to shoot sparks into gas?
@IronSlugs_garage
2 ай бұрын
@@Thelegendking-yj4bm i threw a welding blanket over my fuel tank opening. Welding/ cutting near a gas tank freaks me out haha.
@IronSlugs_garage
2 ай бұрын
@@Thelegendking-yj4bm your fuel neck will slide out of your tank. That’ll help to work with.
@WhiskeyDents
3 ай бұрын
I think you should cut a section of your fender out of the middle. It’s gonna look weird if you don’t.
@Thelegendking-yj4bm
3 ай бұрын
Doing the same build and agree. Going to use a page out of casey customs build
@IronSlugs_garage
3 ай бұрын
Yeah a buddy suggested to change the opening of the fender.
@IronSlugs_garage
3 ай бұрын
@@Thelegendking-yj4bmCasey’s build was great. I do not like modern dash’s on swaps but i definitely referenced his videos a lot.
@WhiskeyDents
3 ай бұрын
@@IronSlugs_garage shouldn’t be too hard. I did it on Lomax
@IronSlugs_garage
3 ай бұрын
@@WhiskeyDents yeah you expert! Haha. I’ll get a plan on what to do with the fenders and focus on those after I got other stuff on the build taken care of.
@Thelegendking-yj4bm
3 ай бұрын
The fuel safety switch where did you mount yours ?
@IronSlugs_garage
3 ай бұрын
I put my safety switch under my bench seat.
@Thelegendking-yj4bm
3 ай бұрын
Are u going to go original on taillights or leds ?
Пікірлер: 25