I just installed the 4300K low beam set. No problems with the installation. No need to reverse power as needed with other kits. FYI, 4300K is the ONLY DOT legal light set for on road use. They appear plenty bright and whiter than the stock halogen set. I will need to lower them slightly. Very satisfied with the results. I cut and soldered some of the ground wire from the drivers side to increase the lead from the passenger ground.
@benjaminsperry5562
5 жыл бұрын
For anyone doing this low beam hid install if you don’t feel comfortable splicing the ground wire to reach the battery find a the closet body ground and you can use that. But this was amazing in depth video and if you are in the Georgia I am looking for some 4 runners buddies
@XenonDepotOffRoad
5 жыл бұрын
Awesome video! Thanks for taking the time to do a review on our lights :)
@shawnsheehan2596
5 жыл бұрын
Do I need the PWM module for a 2018 runner off road?
@dreddy_g
5 жыл бұрын
I assume this will work for all year models of 5th gen? Can I get a product link pls? thank you.
@steffNn
4 жыл бұрын
Just ordered some 9005s from amazon. Ya'll better get some descriptions going on these kits on Amazon. It sells the product way better.
@jalcanites2939
5 жыл бұрын
I have the HID kit from xenondepot on my 2016 Highlander since getting the HL in 2016. I can definitely vouch for the product.
@frizzo01
5 жыл бұрын
You do NOT need the relays with this kit on your 4Runner just the ballasts. I’m running the same kit with 6500K HIDs without them. They send the relays with the kit but they are not needed. Xenon depot also sells a vehicle specific kit for the 4Runner. It’s about $10 cheaper because they remove the relays. I found this after I ordered the kit.
@xjjeepman1
5 жыл бұрын
I have the same kit and emailed Xenon depot and they said I DID need these relays installed so who knows
@justinninke6405
4 жыл бұрын
@@xjjeepman1 Relays are used to eliminate flicker from loss of voltage in an old battery.
@kennyomega6795
Жыл бұрын
fuckin great and easy video bro!
@mikeG-zh5zi
5 жыл бұрын
I encountered a big black plastic cup around the passenger fog light which made it impossible to install the LED bulb. I ended up pulling it off to complete the install. Oddly, the cup was not on my driver side. I don't know if its for protection or not but it wont fit anymore with the heat sink spread out. Did you have on your 4runner. Mine is a 2016 TEP.
@Impulset0
5 жыл бұрын
I had it on mine. Found it easier to reach under with my hands while looking at the front of the fog light to guide it in as opposed to trying to look from underneath.
@sassnchz3906
5 жыл бұрын
Hi, Installed the 9012 XTR HID (5000k) kit on my 2018 Rav4 and it's more than a month now but still struggling to achieve the "Pure White" of the 5000k.... I see the "Pure White" every time I turned-on my headlights but after a few seconds of warming-up it turns to "Yellowish"... In general, does all Xenondepot HID's really requires to wait for a longer burning hours for the color shift to achieve the desired white output?
@chaserampage
5 жыл бұрын
Have you noticed any weird electrical issues or sensor warnings pop up since the switch?
@175firefighter
5 жыл бұрын
I have an "PWM Anti-Flicker Module" and a flat resistor looking heat sink piece in my XenonDepot XtremeHID kit that you don't show here. Any ideas on where they plug into the sequence? I'm stuck here with my jeep on jacks until I can figure this out.
@Jellyballs
4 жыл бұрын
Flyin Rob did you ever figure it out? I hope you got your jeep off the jacks lol
@noesantos7140
5 жыл бұрын
Does this foglight set up blind oncoming traffic?
@mikeG-zh5zi
5 жыл бұрын
How/Where did you attach the LED driver for the fog light?
@steffNn
4 жыл бұрын
I have one eye left, the second one got blinded just now
@v90cross2
4 жыл бұрын
great video! it might be better to wear gloves (when drilling...) for educational purpose. :). Thanks!
@horandestudios
4 жыл бұрын
Why your fog lights are yellow already? from factory?
@QuanTran-vv6mf
4 жыл бұрын
Daniel Horande yellow tint
@djfunknuckle3375
5 жыл бұрын
why yellow for the fog light?
@TheRedEnergy
4 жыл бұрын
Yellow cuts through fog and snow much better with less reflection than typical clear, white lights
@munatoir
4 жыл бұрын
Get another guy to shoot this video! He looks hideous
@opstarledbonnie2370
5 жыл бұрын
Hello, I am sorry to bother you. We are specialized in kinds of auto bulbs for tuning and upgrade. Pls contact me at sales806@opstarled.com if you need.Thanks.
Пікірлер: 28