it's a very nice looking weld job, thank you for sharing your skills
@kimchiwelder8410
2 жыл бұрын
Hi, Fernando Rivas Thanks for watching and leaving a comment! 😎😎
@Mattoilers97
3 жыл бұрын
hope things are good man i'm finally going back to work
@ΓιαννηςΡασκακης
Ай бұрын
Nice video
@abdhulkhan160
2 жыл бұрын
More of this videos its great
@kimchiwelder8410
2 жыл бұрын
Yes, sure. more videos coming. thanks for watching!😎😎
@victorevuarherhe8995
2 жыл бұрын
I am having issues with the angle of electrode for the last pass. Pls any tips. I use 45 and I end up having undercuts
@mathewoconnor2978
2 жыл бұрын
To much angle 15 degrees max
@YT-User1013
7 ай бұрын
@@mathewoconnor2978Yep.
@YT-User1013
7 ай бұрын
This guy shows the angle of the third pass…kzitem.info/news/bejne/2Wia0oinnGmElH4si=Xt-7i9eevoAZyKBk
@usmanaliusmanali1480
3 ай бұрын
What is the rod in mm and ampere is written
@MarineFitter-jh7oh
5 ай бұрын
Before you start welding, are you drying first your 7018 stick welding? Or direct welding no need to dry? Because whe i use 7018 always not continuesly firing, easy for firing but not continuesly, i test with 4" pipe sch40 with 80A 5G position.
@gasperchanda5020
2 ай бұрын
What is the amp for 3.2 mm
@Mattoilers97
3 жыл бұрын
What’s the camera you’re using on your helmet I want to recommend it to some of these other channels it’s so clear and amazing to see it’s so addicting
@kimchiwelder8410
3 жыл бұрын
Hi Matt! Next time I will ask a friend who helped me set up the camera😎😎
@TulanePass
3 жыл бұрын
@@kimchiwelder8410 what camera?
@aarongonzalezreyes2159
2 жыл бұрын
Que oscilación uso????
@louisedouard322
Жыл бұрын
I’m 18 and stated welding when I was 17 your videos helped me through my level one welding course and I was comparable to the people that have been welding for 13 years I love these just have to work on my verticals thank you so much
@kimchiwelder8410
Жыл бұрын
Good job, Louise!👍 I will try harder to make a helpful video! Thanks for watching!😎😎
@indiopatadediablobarbosa5337
3 жыл бұрын
are you in Alberta,?
@kimchiwelder8410
3 жыл бұрын
yes😎😎
@مهرانباورصاد
Жыл бұрын
nice mehran from iran
@amilaudayanga1878
10 ай бұрын
PSI
@victorevuarherhe8995
2 жыл бұрын
I am having issues with the angle of electrode for the last pass. Pls any tips. I use 45 and I end up having undercuts
@kimchiwelder8410
2 жыл бұрын
Hello, Victor!😁😁 Assuming that the amperage is appropriate, the most important thing is the length of the arc. Try to keep the arc as short as possible! Then, if the direction of the welding is from left to right, tilt the angle of the welding rod to the left a little more! Let's hope this helps! thanks for watching!😎😎
@YT-User1013
7 ай бұрын
Your last pass should be at an angle about 15 degrees off of the bottom plate so your rod is more straight in on the top plate and not a 45 degree angle. This shows the angle of the 3rd pass…kzitem.info/news/bejne/2Wia0oinnGmElH4si=Xt-7i9eevoAZyKBk
@Weldinginlove
2 жыл бұрын
Good welding 👏👏👏👍🧑🏭🤗
@kimchiwelder8410
2 жыл бұрын
Thanks for watching!😎😎
@osbaldohernandez9174
2 жыл бұрын
Now let’s see if the gages will fit it
@kimchiwelder8410
2 жыл бұрын
thanks for watching! 😎😎
@Mattoilers97
3 жыл бұрын
are you working through union? Looks nice 👍 getting my 2gf flux down, i like to master one before moving on
@kimchiwelder8410
3 жыл бұрын
yup! Thank you for watching😎😎
@Rohani11
Жыл бұрын
World best work keep it up brother Thanks for sharing your skills for us.
@kimchiwelder8410
Жыл бұрын
I will continue to try to make good videos for you! Thanks for watching!😎😎
@SmotheredDreams
Жыл бұрын
Doing fillet welds right now, but filling the entire thing up in so many layers. Used 30 rods of 7018 in class today!!! Good video, will help for next time.
@kimchiwelder8410
Жыл бұрын
Thanks for watching, SmotheredDreams😁 I hope my video helps you!😎😎
@LilD1988
2 жыл бұрын
Is there a way where we u could help me out with this better
@kimchiwelder8410
2 жыл бұрын
I hope my video helped you a little bit thanks for watching 😎😎
@BlueBoyChavez1993
2 жыл бұрын
Make more good job
@kimchiwelder8410
2 жыл бұрын
sure! thanks for watching!
@marklance1374
7 ай бұрын
Im grade 11 strand TVL specific SMAW this video so learned how to weld fillet i like this video thank you much😊
@petersipp5247
Жыл бұрын
Show is a start/stop please. Thank you.
@amilaudayanga1878
10 ай бұрын
Thanks for sharing your skills for us.
@ΓιαννηςΡασκακης
5 ай бұрын
Thanks
@bobsweldingtutorials3523
Жыл бұрын
God job ❤
@vitaliimedelian4643
3 жыл бұрын
👍
@kimchiwelder8410
3 жыл бұрын
thanks for watching👍👍
@vitaliimedelian4643
3 жыл бұрын
Ok😉
@monroesweldingservices6234
3 жыл бұрын
Why did you not clean all slag off before you started the second and third weld if that was a b3nd test it would cause serious problems
@kimchiwelder8410
3 жыл бұрын
You're right. If we're going to do a bending test, we have to keep it clean! thanks for watching!😎😎
@monroesweldingservices6234
3 жыл бұрын
@@kimchiwelder8410 been teaching young minds for 7 years now and did powerplants and pipeline for 20 years
@kimchiwelder8410
3 жыл бұрын
@@monroesweldingservices6234 Wow, You have a great experience!👍👍
Пікірлер: 52