Good install doing the same on a 97 Tahoe and figured out how to make it work now…Thanks
@jackperry9369
2 жыл бұрын
Thanks sir appreciate it
@gerardolopez5875
2 жыл бұрын
👍👍👍 nice,,, I was thinking on that, I gt a sub sway bar,,, thinking to install it on my 72, since its sprigs on rear,,
@laurencevillegarage
2 жыл бұрын
Go for it!
@jays6.021
Жыл бұрын
Great Video, I purchased everything in the video. How much would you charge to fab up the brackets I’m in rockwall as well.
@laurencevillegarage
Жыл бұрын
I no longer live in Rockwall, I now live in Sunset. That’s near Bowie.
@jays6.021
Жыл бұрын
@@laurencevillegarage would you be interested in Fabing the brackets. If I sent you the perches for the u bolts & the rear brackets for the frame
@laurencevillegarage
Жыл бұрын
The rear brackets would be hard for me to do correctly without having the truck here to measure the length by. Bar should be basically parallel with the ground. Depending on what your suspension looks (stock height, lowered 2, 4, 6 etc) I would not be able to determine the correct length. There are some very capable shops in Rockwall/Garland area that might be a better choice.
@lj6278
2 жыл бұрын
Good video, I have a 97 two-door Tahoe, they didn't come with a sway bar because the gas tank is in the back, do you have any ideas that might work?
@laurencevillegarage
2 жыл бұрын
While I don't have a truck like yours to look at, I'm sure a bar can be fitted to it that would not interfere with the rear tank. Similar year Suburban had some bars that may work or make another years truck bar fit. It takes some creative thinking, but the attachment points are not that difficult to figure out. I'm sure it can be done, but without seeing what you have to work around I can't be too specific. Good luck with your project!
@carsgunsandfitness6462
2 жыл бұрын
If I have a 96 Tahoe would putting on a NBS swap bar do any difference?
@laurencevillegarage
2 жыл бұрын
If you already have a bar, then the difference would be minimal. IF you don’t have a bar, then yes, you would see a difference. Check under your frame. Trucks and SUVs are different. I’m sure it could be done, just have to get creative to mount.
@tliebelt13
2 жыл бұрын
Would this work on a 5/7 drop if the end link mounts were adjusted/shorter?
@laurencevillegarage
2 жыл бұрын
In a word...yes. After I put the motor in and finally put the truck on the ground and let the suspension settle, I had to raise the upper end link position about 1.5" for the bar to be parallel to the ground (with a 4" rear drop). For a 7" drop you may need to cut the end links (dog bones) and overlap them to get just the right position for the bar to be parallel to the ground then weld them up. Not a problem, easy enough to do.
@billscreations1999
2 жыл бұрын
Does it make a difference when you're going around corners
@laurencevillegarage
2 жыл бұрын
Although the truck is not finished and therefore has not been driven yet...yes. A rear bar makes a very noticeable difference in handling. I plan on putting one on any OBS I have. As a side note, went to the salvage yard a few days ago and found a '93, half way stripped, but suspension intact. It had a Hotchkis Performance front and rear bar setup. Got it for cheap! Also pulled, what turns out to be a 3.73 limited slip rear end assembly for cheap as well. It pays to go scrounging around at your local yard!
@maxtaylor8509
2 жыл бұрын
Mr Lawrenceville those dog bones for the rear sway bar look a little too long and they might hit the ground & bend/break if you are run over pothole or speed bump etc..just saying.
@laurencevillegarage
2 жыл бұрын
In the cover picture they may look that way. However, when installed and adjusted, the bar is parallel to the ground and the bar offers up 9.25" of ground clearance. The lower portion of the rear end has 8" of ground clearance. So, no issues at all.
@wayne2160
2 жыл бұрын
What made you used 30mm over the 32mm?
@laurencevillegarage
2 жыл бұрын
I had the 30mm bar first when I ordered the frame bushings, then I got the 2nd bar. I didn’t want to order a second pair of bushings when I already had a pair that worked. I’ll use the other bar on the next project.
Пікірлер: 20