I saw this changed my mind bought a real Dremel from Amazon cost 150 but actually works thanks for the video
@ChrisThedudenurse
9 ай бұрын
Well I'm glad I could help.
@COEYRN
6 ай бұрын
I wanted to give you some advice. If you happen to come across an old Dremel and I'm talking 20 years old, for cheap, grab it. The only thing better than a Dremel is having two Dremels. After 25 years my Dremel started to slow down, at intervals. I thought it was done. I went and bought a new one. I couldn't believe the difference. The new one is HORRIBLE compared. I didn't go cheap either. Expressing my disappointment to a friend, then listening to a good scolding of, the typicsl they don't make em like they used to you twit. He helped me fix it. So 7 bucks for a pack of 2 brushes. Took the advice of a very kind man on KZitem to get as much dust out as possible. Ta-da, I am not even exaggerating it's better than my new one. If you do go looking for a second hand one Just remember it will be small stuck in the bottom of a box And covered in probably white powder, and it will probably blend in with everything else in the box and it might be hard to see turn the box upside down that's what I always do. 2s better then one. Plus buy the quick change bits whenever you see them, they sell fast. Pardon me I apologize this is a perfect stranger telling you what to do I'm not trying to be the guy I just was really surprised at the difference between the new and the old and the disappointments I felt.
@julianezequiel9371
25 күн бұрын
the cheap multitools are pretty good the off brand accesories is the crap for real have used dremel and some other brands and chinese ones, they are pretty good for the prices but ohboi the accesories, the chinese ones are shitty cut wheels def buy dremel, sanding drums and other kind of abrasives go for the cheapest will be better bang x buck
@jonduggan7433
5 күн бұрын
Those rotary tools work extremely well when used as they are designed to be used. They were not designed to take the place of an angle grinder or air cutoff tool. They are designed for wood, plastic or very thin metal. Like a couple mm thick metal.
@ChrisThedudenurse
5 күн бұрын
I’d just stop at plastic, they don’t do much after that.
@CagdasInsaatMalzemeleriLtdSti
2 ай бұрын
That rotary tool very nice, I use with powerbank :)
@ChrisThedudenurse
2 ай бұрын
nice, portable.
@tracyskoken2152
Ай бұрын
Thanks bunches..❤
@BrantlyFrederick
6 ай бұрын
This would be be fun to have next to my 3 real dremels, even the dremels won’t cut exhaust pipe too well but it’s perfect for other stuff, 2 of my dremels can vaporize plastic basically so I don’t need anything with a dumb amount of power any more
@ChrisThedudenurse
6 ай бұрын
Oh she ain’t got no power that’s for sure.
@x_istance7265
2 ай бұрын
I sell stuff at the farmers market that I’ve welded im 18 and brings in a little more money I use the 50$ one from harbor freight I use it for the small stuff like flowers and letters and other designs I cut out of sheet metal as I don’t have a oxy torch yet and it’s WAAAY better for small stuff then my angle grinder
@ChrisThedudenurse
2 ай бұрын
It seems to do well with that stuff for sure.
@COEYRN
6 ай бұрын
You don't need to buy any at a regular store . Honestly just go to any Reuse Recycle place, and you'll find tons of these. It would appear it's one of those things that people just don't bother with cuz they shatter. Plus thanks
@toxicity6629
6 ай бұрын
Yeah they sell the black ones with the lines going through it they keep the blade in tact while you cut a lot better than the brittle sandpaper looking ones
@classydays43
21 күн бұрын
Will this tool, designed for jewellery and small stuff, cut this thing, which is better suited for an angle grinder, with a wheel that's being used improperly? All jokes aside, these resin wheels don't like to be plunged.
@ChrisThedudenurse
21 күн бұрын
Or used at all for that matter, this was just a quick test.
@classydays43
21 күн бұрын
@@ChrisThedudenurse they take a little finessing. I use them to sharpen tiny (0.3-1mm) drill bits because the grit is fine enough for it.
@pleaseusernamework
25 күн бұрын
Have the Dremel version. They too break very easily. Not very good at all for cutting metal. Extremely fragile accessory. Going to get the strong one at some point.
@ChrisThedudenurse
24 күн бұрын
Yeah this is not what these were designed for at all
@infernaldaedra
10 ай бұрын
Definitely better as a engraver or Polish tool where you want less if a chance of hurting the surface
@ChrisThedudenurse
10 ай бұрын
no absolutely not a cutter.
@AquaTech225
5 ай бұрын
Engraving is ok. An that even depends on what material. But polisher. Not so much. It just don’t have the juice behind it to do much with that. It would be slow going for sure
@diymaster101
Ай бұрын
Use angle grinder.
@ChrisThedudenurse
Ай бұрын
I do have one, this was just to see if it would work.
@tumbleweed1976
4 ай бұрын
So the tool works just not the accessory/bits in this case?
@ChrisThedudenurse
4 ай бұрын
I’d definitely buy a better set of accessories yes.
@I_throw_coins_at_squirrels
Жыл бұрын
Dawg that’s a grinding wheel or sm not a cutoff wheel
@ChrisThedudenurse
Жыл бұрын
It’s the set that came in the kit I’d definitely recommend buying an actual cut off wheel
@I_throw_coins_at_squirrels
Жыл бұрын
@@ChrisThedudenurse yeah, I got that same tool at harbor freights and I got the set that was next to it and it kinda works, but stops when you put the slightest pressure
@erintaylor5923
7 ай бұрын
Those are sanding discs. Not meant to cut. 🤦🏻♂️
@vietthu16
3 ай бұрын
I don't like the high vibration of this one. Hurts my arm.
@ChrisThedudenurse
3 ай бұрын
Oh it do shake
@tracyskoken2152
Ай бұрын
How do u put it on?
@ChrisThedudenurse
Ай бұрын
with a tiny screw driver.
@Greenpoison911
10 ай бұрын
Would you recommend this for cutting up a pair of jeans?
@ChrisThedudenurse
10 ай бұрын
It’ll cut jeans no problem, I wouldn’t go much thicker than that
@jaycesalas4864
9 ай бұрын
would you recommend this for cutting a jason voorhees plastic mask
@ChrisThedudenurse
9 ай бұрын
Should do fine as long as the material is plastic and not metal
@jaycesalas4864
9 ай бұрын
@@ChrisThedudenurse thanks where can i get this dremel tool
@ChrisThedudenurse
9 ай бұрын
@@jaycesalas4864 harbor freight
@mattwarrensocal
4 ай бұрын
If er visits were a short
@ChrisThedudenurse
4 ай бұрын
Nah I always wear too much protective equipment
@AquaTech225
5 ай бұрын
That harbor freight one is junk. That being said. If you need a single use engraving or something like that works decent for that. But if you’re looking to actually get work done. Pass on this one. I do have one of these also. I can’t remember what I originally got it for. But the disk ect it comes with is just as much junk. An has very little strength/power. But for that one time use for something simple. For the price you can’t beat it.
@ChrisThedudenurse
5 ай бұрын
This was just a quick test. I don’t use it for this all the time.
Пікірлер: 45