Gary Garcia is the man! He did my stand alone harness here locally in AZ great guy very knowledgeable. Swap looks great by the way. I love my 92 6.0!
@Joe_Jackstands
7 жыл бұрын
Darnell Jenkins I learned alot from all of his videos. If it wasnt for him i wouldnt know what i was doing half the time. He is a great resourse to have.
@skeeter5283
4 жыл бұрын
Thanks for the shout out!!! Great job on your truck, it is literally easy if you take one task at a time.
@martinperez249
2 жыл бұрын
Hi joe I’m currently doing my ls swap and I’m trying to figure out the Vss wire is it the dark green wire you had your light on in the video?
@Joe_Jackstands
2 жыл бұрын
Pin 50 on red connector is VSS out. It's green and white
@carvisgooger1045
2 жыл бұрын
Did you use the factory oil pan on the motor
@Joe_Jackstands
2 жыл бұрын
Yes I used the factory ls truck pan
@OBSDeathProof
5 жыл бұрын
Great video, came recommended. I am swapping my 95 as well, did you tune out the transmission range signal. I'm hearing and reading that the 95's came with it in the shift column. Thanks in advance.
@Joe_Jackstands
5 жыл бұрын
I just plugged in the range switch and used like stock
@OBSDeathProof
4 жыл бұрын
@@Joe_Jackstands Sounds good thanks. Most of my swap has been trial by error. Part of the adventure I guess. Thanks again.
@Joe_Jackstands
7 жыл бұрын
Going from a Tbi motor to LS is way worth it. On a 95 do a stand alone harness and tap into everything. If it was a 96-98 then I would buy a plug a play harness
@accsolidwaste6522
6 жыл бұрын
my 95 c1500 has a 4.3v6 with a 5 speed... I'd like to keep the 5 speed and later update to t56... just picked up a complete 2001 tahoe to snatch the engine out.
@redrum0243
4 жыл бұрын
bro im doing a 5.3 swap and I need Lot of help ,can I send you my number so I can text you few question??
@SuperBogdaddy
5 жыл бұрын
Doesn’t the tcc wire from the ls pcm go directly to the factory break pedal switch. Only thing I’m confused about during my swap that I haven’t found the answer to
@Joe_Jackstands
5 жыл бұрын
Yes the tcc goes to the brake pedal.
@jameslarue8678
7 жыл бұрын
I'm thinking about ls swapping my 95 k1500. Is it worth the money getting a plug and play harness done or just go with a stand alone ?
@chadowens9215
6 жыл бұрын
I'm new at this and seen a crap ton of 4x2 but 4x4 I have a 91 k1500 and a 02 avalanche 1500 for a doner both are torsion bar will it work if use everything out of the avalanche?
@Joe_Jackstands
6 жыл бұрын
chad Owens I haven't done a 4x4 but it's all the same it should all work fine.
@1madrs637
6 жыл бұрын
Nice video!
@taylorh3930
5 жыл бұрын
I've bin thinking about doing a 6.0 4l80e swap into my 98 Z71. My biggest fear is getting the speedometer and stuff to work. Also can I run my factory 98 air box or the factory 6.0 air box? If I do this swap I want it to look as OEM as humanly possible I see lots of people run socal cold air intakes (they are actually hot air intakes) and I'm just not a fan of the looks of them intakes.
@al4318
6 жыл бұрын
How or what did you use for the gear shifter lever ?
@five9carmageddon888
6 жыл бұрын
I just bought a 94 yesterday for $250 runs and drives but didn't have wheels and tires and 3rd gear and O/D are going out and it didn't have tail lights. That's why it was so cheap but anyways I was considering doing an is swap if I do is there any way I could contact you about the fastest way to get it done to make it just driveable. All I need is tach, temp, and oil pressure for the time being
@Joe_Jackstands
6 жыл бұрын
96GMCSierra its a really easy swap once you get into it. Feel free to email me at actionj5828@gmail.com and ill answer question
@Triggerman2505
6 жыл бұрын
I noticed you don't have a return on the fuel rail?? how did you manage that or was it added later? I am in the middle of my swap and sine my 06 L33 does not have a return, I am looking to get around it, need a fuel rail from 2000 or 99 I am told, which I did get, but trying to sort out the fittings? Also, I have an 88, so I don't think they had a DRAC so getting the Speedo to work will be a challenge.
@Joe_Jackstands
6 жыл бұрын
Theres a return on this one might it not be hooked up in this video but its on there. If you dont have a return style intake run a corvette filter to make it work.
@Triggerman2505
6 жыл бұрын
Thank you!
@pmotorsports8276
4 жыл бұрын
If you don't have return on rails. By a Corvette filter
@jmc7991
4 жыл бұрын
I’m having such trouble with this. Can anyone answer exactly witch of the three wires from the pcm goes the the DRAC system & what color wire? I have the 4l80e 4x4 & just can’t seem to figure out where the 3 vss wires go from pcm. Any help would be appreciated. Thanks!
@Joe_Jackstands
4 жыл бұрын
red connector pin 50 VSS output. Run to the drac module
@jmc7991
4 жыл бұрын
Thank you for the response. I have that correct but I believe I have a wiring harness from a 2wd & have a 4wd with the speedo in the tail shaft. I may need to set the computer for a 4wd & take my wires from my out put sensor to it & possibly also hook up my DRAC to it. Not sure yet but when I figure it out I will be sure to post my results on here. Meanwhile if any can come up with a solution I’m all ears. As of right now I haven’t figured it out yet. Thanks.
@jmc7991
4 жыл бұрын
The wiring harness came from a 4l60e
@jmc7991
4 жыл бұрын
SOLVED... quick update...let you know soon. Thanks but no thanks.
@juanmorquecho1712
7 жыл бұрын
Looks awesome man Hey do you have the part # for dirty dingo motor mouths
@Joe_Jackstands
7 жыл бұрын
dirty dingo dd-2550c
@lsgang1077
6 жыл бұрын
Did you use the stock 95 trans? What wiring do you have to do to make it work right with the newer ls engine ?
@Joe_Jackstands
6 жыл бұрын
Alexis Villasenor i used the newer ls 4l60e trans. Wiring just make a stand alone harneszls of lt1swap.com and tap in for your gauges
@lsgang1077
6 жыл бұрын
Alright thanks for the reply I understand the standalone harness process part. my truck is the same year etc as yours just in red now what I don’t quite understand is the part where you mate the ls harness with the Tbi harness to make the newer tranny work with no issues as far as it knowing when to shift etc. I’ve searched everywhere for a diagram but can’t seem to find info on that particular wiring.
@Joe_Jackstands
6 жыл бұрын
Alexis Villasenor use the ls harness the trans wiring is all in it already.The newer ls ecu will control the trans.
@lsgang1077
6 жыл бұрын
Alright man got it! Thanks
@dalton7535
5 жыл бұрын
How did you find out what each wire does on the ECM?
@Joe_Jackstands
5 жыл бұрын
lt1swap.com has it all labeled out for the ls harness. for the 95 i just googled eached one as i went some where easy to figure out the others took a little more looking around to find
@stevendiemer2833
5 жыл бұрын
What fuel pump did you use tbi or something else
@Joe_Jackstands
5 жыл бұрын
Tbi pump wont work. It dont have enough pressure. I used a walbro 255 from highflowfuels.com. you can also use a ac delco ep381 stock pump out of 96-98 trucks
@stevendiemer2833
5 жыл бұрын
Thank you sir
@jerrygutierrez161
3 жыл бұрын
What u do for fuel lines
@Joe_Jackstands
3 жыл бұрын
I used ls fuel lines from donor truck. Compression fitting them to factory truck lines
@jerrygutierrez161
3 жыл бұрын
@@Joe_Jackstands o venture into a swap and I think that stand alone harness is scary ..... I have donor truck wire harness n pcm but I keep seeing all this videos about cutting wires out .... like why I got to do that if the truck was running with that wire harness
@Joe_Jackstands
3 жыл бұрын
@@jerrygutierrez161 its not bad your just pulling wires out you don't need. Its not that bad
@Lalo8689
6 жыл бұрын
Wats the numberon the Engine light wired
@Joe_Jackstands
6 жыл бұрын
Red connector pin 46 runs straight to check engine light
@Lalo8689
6 жыл бұрын
Joe Jackson thanckyou
@jdmdrew575
6 жыл бұрын
There isnt anyway to use the 95 4l60e?
@Joe_Jackstands
6 жыл бұрын
JDM_DREW if it was a 96 newer you can a 95 will be way different electronics and the ecu couldn't run it
@Lalomoran24
5 жыл бұрын
dude u just answered my questions
@ThePriestlyMan
5 жыл бұрын
Can you give me a part number on that equus gauge kit?
@Joe_Jackstands
5 жыл бұрын
Equss 9848
@ThePriestlyMan
5 жыл бұрын
I just got the kit and it didnt work. You're using the original 95 oil pressure sending unit?
@Joe_Jackstands
5 жыл бұрын
@@ThePriestlyMan yes I'm using original oil pressure sensor.
@Joe_Jackstands
5 жыл бұрын
@@ThePriestlyMan I thinking there was a weird elbow on my factory one. So it was the oil pressure sensor,to the elbow that reduced it, and then to the equss guage adapter.
@ThePriestlyMan
5 жыл бұрын
That worked! Thanks!!!
@jamesphillips8518
4 жыл бұрын
will a stock 95 4l60e work with this swap
@Joe_Jackstands
4 жыл бұрын
No a 95 4l60e is different any 96-up will but the 95 is its own year.
@gerardolopez5875
Жыл бұрын
@@Joe_Jackstands @ is it true 95 transmission s only work on same year?
@Joe_Jackstands
Жыл бұрын
@GerardO Lopez yes 95 only work on 95s. They are wired different inside them
@gerardolopez5875
Жыл бұрын
@@Joe_Jackstands @ o ok, dis u sold the obs ?
@juanmorquecho1712
7 жыл бұрын
How is your swap
@Joe_Jackstands
7 жыл бұрын
Well worth the money. runs great and smokes the tires like nothing. I love it.
@2nd-gen86
5 жыл бұрын
Hey I have a 1986 Camaro Z28 IROC one owner 66000 original documented miles for sale red on red interested? Look at the videos
@Joe_Jackstands
5 жыл бұрын
I love 3rd gens and I would of been interested but I just bought a 99 c5 vette
@2nd-gen86
5 жыл бұрын
$3000
@Joe_Jackstands
5 жыл бұрын
@@2nd-gen86 very temping but i cant afford another car right now. I have 2 projects cars already and need to get them going the way i want
@Charlie-zo2nu
5 жыл бұрын
the 5.3 VORTEC is LS based but it isnt an LS, there are major size differences.
@redrum0243
4 жыл бұрын
bro im doing a 5.3 swap on my 94 ,anyway I can send you my number i need some help doing it all myself and its my first time
@Joe_Jackstands
4 жыл бұрын
Email me and see if i can help actionj5828@gmail.com
@hellpandart4133
6 жыл бұрын
Do u have a part list you used for this swap u can email me plz
@Joe_Jackstands
6 жыл бұрын
simple really.. 5.3 motor 99-02 99-06 4l60e transmission tuned ecu 99-02 diy ls harness following lt1swap.com write up dirty dingo slider mounts for 88-98 highflowfuel.com 88-95 255 fuel pump 99-02 lower radiator hose stock power steering lines fuel lines compression fittings on feed and return line 99-02 throttle cable ebay cold air intake stock exhaust manifolds from 99-02 98 ls1 3 prong temp sensor and wires for temp gauge oil pressure sender used a adapter in a equss guage pack i think thats about it. really easy swap on a tbi truck
Пікірлер: 84