I'm no welder and I have absolutely no intention of becoming a professional at it. But occasionally I have to weld something around the shop. I know a lot of you pros are giving him hell, but for us folks that just need something stuck together from time to time, I find it helpful.
@user-lb2og8ug4k
6 ай бұрын
Все мы учимся и познаем.
@mateusseer5353
6 ай бұрын
Spot on. I think they're full of shit. If theyre so clever, why not pist a video of how they think it should be done?
@LostenFree
6 ай бұрын
Good point, when they don’t have the right oil for my car at the gas station I just buy whatever they have
@Journeyforgeusa
6 ай бұрын
@@LostenFree well if you're in a pinch (I'm assuming would be the case if you're buying your oil from a gas station)a slight variance in viscosity won't hurt anything in the short term. The wrong oil is sometimes better than no oil at all.
@Fizz-Pop
6 ай бұрын
Half the people online that shit all-over others attempts have never actually done it themselves. It IS pretty easy to be an expert video watcher after all.
@tom-vs3lf
8 ай бұрын
I didn't realize the reason they're using 6013 all the time is because that's all that's available. Welding thick to thin you always put the force of your arc on the thicker piece.
@user-lq4mh5oc1q
7 ай бұрын
Always
@god_speed47
7 ай бұрын
Yes sir
@Djkomedikomentarbawahelinadetn
6 ай бұрын
Paswe
@cosh7670
6 ай бұрын
ماهو قانون اللحاام / المعادلة
@johndavid6956
6 ай бұрын
Without start/stopping a million times to make a single weld.
@johnbelwell2461
7 ай бұрын
Too much bogus criticism in the comments. These videos are meant for people who have a welder around and want to repair their fence door or whatever they need to do to fix stuff like that. I weld for quite some time, definitely not a pro, but the reason that got me into welding was not the desire to become a professional welder, just fix things, and that interest got me involved more in it. I started with tacks and learnt how to run a bead, use different electrodes, weld on thinner material etc, got proper equipment, and it involved into a hobby. I'm a mechanic and it's the same way if i criticize people who change their oil on their own saying they are are not mechanics, not only it's non sensical but also defeats the whole purpose of the reason they do it, even if it's for cheap or they want to get their hands dirty and get into stuff to learn more.
@warrenpeas
6 ай бұрын
well said. being able to weld metal together that isnt bearing a lot of weight or peoples lives, even in the most primitive way is a huge step up from duct tape and bolts and nuts. a hell of a lot of stuff wouldnt be thrown in the trash if peopel just knew how to tack weld to fix metal DIY.
@cornfarts
6 ай бұрын
Amen brother
@julez5114
6 ай бұрын
Well said!
@user-yf9lg2hd7r
6 ай бұрын
There's a difference in doing it wrong, and trying to instruct people how to do it wrong. The difference is what is at stake if it fails, could it injure someone or even worse kill someone. That weld is going to break with very little stress, would you put your kids under something like that.
@nospoon4799
6 ай бұрын
Noice.
@VladimirBashmakov
Ай бұрын
Досмотрел до конца. Сижу жду когда зрение вернётся 🥴
@user-bv3xd8cj3d
Ай бұрын
Дык в сварочной маске нужно смотреть-то. Эх молодёжь, всему вас учить надо.
@VladimirBashmakov
Ай бұрын
@@user-bv3xd8cj3d 🤣🤣🤣👍 тупанул че-то я
@saidmuhammadlabazanov6075
23 күн бұрын
@@VladimirBashmakov😅
@user-cy2dv5te6w
8 ай бұрын
Я шлак никогда не отбиваю, так крепче, а если ещё проволкой обмотать по кругу то вообще на века 😊
@user-eu3il1ru7p
8 ай бұрын
Приветствую Вас, коллега !!!
@msattey5650
8 ай бұрын
И намертво склеить скотчем!
@user-cy2dv5te6w
7 ай бұрын
@@msattey5650 спасибо за совет! Про скотч я совсем забыл😁
@ottowulff3277
7 ай бұрын
Крякнуть, плюнуть и надёжно склеить скотчем.
@ЖЕГЛОВ-71
6 ай бұрын
Никто не вспомнил про синюю изоленту. Слабаки)
@stevewhitler1452
7 ай бұрын
Glad I grew up learning how to weld in a welding shop instead of learning the wrong way on KZitem
@victorrivera4856
7 ай бұрын
Muestra el lado correcto
@Overt_Z
6 ай бұрын
Wish you people always shitting on other peoples work would actually verbalize your superior knowledge and explain what was done incorrectly and what could be done better. I’m certain you didn’t as well all the other keyboard tradesmen didn’t learn the trade by having someone stand over your shoulder and say your work is shit, you were taught and showed how to do it properly.
@stevewhitler1452
6 ай бұрын
@@Overt_Z That knowledge comes at a price. Only a fool would give it away for free!
@somedude2221
6 ай бұрын
I dont think you noticed but this entire channel seems to be a troll channel that does bad welds on purpose.. or at least i hope so
@KingKobra98
6 ай бұрын
Wish you would keep your comments to your trade buddies than to everyone on KZitem.
@user-xx3zz3uf6m
Ай бұрын
Автор,самая хитрая хитрость для тебя персонально:варится всегда с толстого на тонкое.
@robertgossas3711
7 ай бұрын
Welders ... I don't think i've ever seen or heard of welders agreeing how something should be done. Picking on eachother like hens.
@endurofan9854
7 ай бұрын
exactly, everyone acts better than the other, 🙄
@JD-wn3cc
6 ай бұрын
Sad thing is, half of them won't even be welders. They'll just talk it up because they've watched some videos or it's not how they saw their uncle once do it
@tornado100able
6 ай бұрын
I mean, are there that much welders out there? I've never met one in my life
@benb9151
4 ай бұрын
Company buys $15k in equipment, gives them a supervisor, and slides them a paycheck based on their hours, and they think they should be on national television
@robertg8930
Ай бұрын
As a certified structural steel welder I can tell you the only opinion that matters is my 100% continuous inspection guy looking over my shoulder all day.
@PimentoZ24
8 ай бұрын
Slag inclusions have entered the chat.
@arnholm1384
7 ай бұрын
Yup 👍
@tothlacko8290
6 ай бұрын
Just a smidge😂😂😂
@jrussell5243
Күн бұрын
Slags are always a welcome addition
@brettpomeroy6804
8 ай бұрын
Fit and function. While not the strongest weld. Definitely inclusions with starting and stopping. But it should be fine for its purposes. Most welders think ever weld needs to be as strong as possible. Not as storng as is needed
@CatharticSense
7 ай бұрын
So it's just an inferior method? Or is it faster than doing the stronger binding methods?
@brettpomeroy6804
7 ай бұрын
@CatharticSense it has more to do with availability of tools and material. A TIG weld would be the strongest. Mig weld would work well too. But it doesn't seem he has access to all of that. This should work fine for it's pourpose.
@joescheller6680
4 ай бұрын
In this case the light duty metal is way lighter than the weld
@samueldominguez8680
2 ай бұрын
Tampoco es para sujetar un puente por el que pasan camiones!!! Así y todo esos puentes hechos por profesionales tambien se caen ...no critiquen
@SeisKyomi
6 ай бұрын
The Internet has convinced me that there is no proper way to weld anything ever. There's always several people in the comments saying that what ever was done is the wrong way to do it.
@talon3995
6 ай бұрын
I've lost count of how many welding videos I've watched designed to teach others how to weld properly. Almost all of them forget to show the basics of the art. Making sure the metal is clean from rust, paint, dirt etc.
@michealdavis9884
Ай бұрын
Usually this is why you use a stick it doesn't matter how clean but mig is different it needs to be clean ,so if u are fixing a old PC of equipment use stick if your doing something new or needs to look real good use mig
@user-mk2hp8ne9h
6 ай бұрын
Я один не понимаю, в чём хитрость то? В том, что он нормально в один проход и без отрыва не может пройти шов или в чём?😂
@user-nh4ij3gc5b
6 ай бұрын
не пязди!!!
@user-ji7sc5dz9g
5 ай бұрын
В том, что зажигать и 2/3 ванны держать на толстом и 1/3 на тонком.
@marioguajaca8307
Ай бұрын
Con el amperaje adecuado y cargando la soldadura más en el metal más macizo Claro que se puede
@Aleksandr-Kostenko
Ай бұрын
Тоже не в понятках!!! Анонс - просто замануха.
@user-ed9oq1oj8x
Ай бұрын
Суть в том, что в данном случая не надо варить без отрыва, ибо тонкий металл перегревается и прогорает. Электрод надо отрывать, чтобы дать тонкому металлу немного остыть.
@bandanabanana3162
8 ай бұрын
There's nothing wrong with some constructive criticism. Some people need to go to welding school. If he has been, then they should fire the teacher.
@noobbuilderproductions7865
7 ай бұрын
Lol
@inocinventions532
6 ай бұрын
They dont teach there thin metal welding... all is thick piping and rootpass... thas why these rootpass boys cant weld in househokd settings because household settings mostly use thine metals....😁😄😄
@InkArtista-nt6zk
6 ай бұрын
What is the right way? Im just curious
@austinlacount
6 ай бұрын
Bullshit a stringer is way better than slag inclusion and weak tacks!
@Overt_Z
6 ай бұрын
Wish you people always shitting on other peoples work would actually verbalize your superior knowledge and explain what was done incorrectly and what could be done better. I’m certain you didn’t as well all the other keyboard tradesmen didn’t learn the trade by having someone stand over your shoulder and say your work is shit, you were taught and showed how to do it properly.
@rafitarafitamedinanunez6074
6 ай бұрын
Gracias carnalito...por ese consejo.....yo la estaba cagando cuando soldaba....un saludo desde.... MÉXICO
@user-gf6yy8pl1f
Ай бұрын
Parabéns por repassar o seu conhecimento muitos serralheiros esconde isso dos ajudantes . Que o senhor Deus continue abençoando o seu canal no KZitem. Não tive essa oportunidade quando comecei a maioria dos serralheiros tudo egoísta.
@309atul
7 ай бұрын
Do I need to wear welding glasses while watching these videos ??
@yoitsvenus616
7 ай бұрын
If your not joking, no you dont need to wear them
@309atul
7 ай бұрын
@@yoitsvenus616 thanks for opening my eyes
@iAmSavvi
7 ай бұрын
@@309atul 😂😂😂😂
@t.bickle
7 ай бұрын
safety first!!!!
@thatDUDEfromMAINE
7 ай бұрын
yes always😎
@franciscominguet6916
Ай бұрын
Excelente video para aprender a soldar gracias
@user-ux4dy5dm7c
Ай бұрын
Пайка и сварка - это совершенно разные процессы.
@user-lp9xh7ds2v
Ай бұрын
Сварщик. Варит. А. Не Пояет. А. Паспортист. Это. Ювелир. Может. По зеркалу. Варить. А. Что Показали это. Баловство. Только. Для. Себя. Я. Слесарь. По. Трубопроводу. Был Учеником. И. Знаю. Кто. Такие. Паспортисты. 🎉🎉🎉🎉🎉🎉🎉
@ZayatsT1000
6 ай бұрын
Привет, я тоже сварщик. Для видео в обучалке делай окончание шва. Пару точек или задержку в конце, а то плохому научишь. Надеюсь что не воспримешь меня как хейтера.
@user-zt2we5pu4x
Ай бұрын
Автору пох на твой комментарий.
@PedroPauloprete-mg7nz
8 ай бұрын
Isso mesmo solda com perfeição.. Parabéns. Vou lhe mandar UM FELIZ NATAL E UM PRÓSPERO ANO NOVO A VOCÊ E FAMÍLIA EM NOME DO SENHOR JESUS CRISTO AMÉM 🙏🥰. DEUS ABENÇOE GRANDEMENTE AMÉM 🙏🥰. FELIZ NATAL.
@marioeduardovillena
6 ай бұрын
Exacto!!🙌🏼 este es el video que he buscado mucho 🤩 Gracias gracias por compartir 🏁
@charliehaddad4614
6 ай бұрын
Thats one of the more nicer welds I've seen on shorts
@eduardomontalvan3090
Ай бұрын
Exelente máquina amigo buena tú técnica gracias por enseñarnos saludos desde Perú 👏👏👏👍👍
@user-wk7rx9fm7q
5 ай бұрын
Метал при сварке надо брать не тонкого метала, а с прутка!
@destroy_swarm
6 ай бұрын
И забыл капнуть последнюю каплю 😂
@user-zt2we5pu4x
Ай бұрын
Как залупой не тряси, капля упадёт в трусы. 😂
@user-bf3wn6dc1y
6 ай бұрын
Тонкий металл хорошо варить прямой полярностью этот шов Я бы заварил в один пароход я не профессионал Просто приходится самому для себя кое-что делать обратная полярность варю толстый металл там где плавится электрод меньше а металл плавится больше
@user-gc3bb8uc2d
Ай бұрын
Как раз всё на оборот
@oswaldoluizgalino6756
Ай бұрын
Isso é que eu chamo de uma obra de arte!! que perfeição!!
@user-fr4ei2eu5r
8 ай бұрын
Какие то не понятные соединения, для чего видео, тоже не понятно 😂
@serge_msv777
7 ай бұрын
Когда "непонятные" начнешь писать СЛИТНО, так сразу начнёшь понимать.
@user-fr4ei2eu5r
7 ай бұрын
@@serge_msv777 не понятно пишется отдельно, учите русский язык. 😡
@AirUnit313
7 ай бұрын
@@user-fr4ei2eu5rнепонятно мне почему это не понятное видео тебя смущает😂
@JRsVsO
6 ай бұрын
You Russians are hilarious 😂
@AirUnit313
6 ай бұрын
@@JRsVsO thanQ🫠
@pedrooscarbarreyro332
Ай бұрын
No soy un profecional, pero practicando he llegado a defenderme en la materia lo y he logrado fabricarme tres tipos de bicicletas de tres ruedas dos para oies y una de mano que son muy fitografiadas en mi ciudad Posadas Misiones Argentina
@Daniel-mg6oi
Ай бұрын
Eu aprendi a fazer alguns serviços de solda elétrica! Fui aperfeiçoando e hoje consigo fazer solda em lata de escape sem problema algum muito útil esse vídeo para quem é iniciante 🔰😅
@TrashPanda71
19 күн бұрын
Only thing i could add is turn the amps down a bit more, burning kinda hot for the situation.
@user-bs3dk9dz2w
7 ай бұрын
Первый шов соответствует достойной зарплате😂
@yusup4844
8 ай бұрын
Нужно смотреть на толщину металла в данном случае катет шва должен быть не таким большим,можно было на первом шве остановиться
@user-zl7cw4mx6u
Ай бұрын
Muy buena esa enseñanza. Para los que están aprendiendo.
@JohnDoe-pe1fh
7 ай бұрын
Why does everybody use 6013? … because it’s easy to make look good very easy rod to run and isn’t good for anything seriously so it’s cheap
@kri6033
7 ай бұрын
exactly, and weirdly easy even to eruin the weld incarcereting some garbage under it
@throngcleaver
Ай бұрын
Back in '78, I was taught to drag the slag hammer tip back and forth on the weld, instead of hammering marks into it. Just sayin'.
@angeljunco9832
21 күн бұрын
Bien explicado Gracias!
@OzeiasApucarana
6 ай бұрын
Muito obrigado. Comprei uma maquina desta, e apanhei bastante no começo.
@vityanli6803
5 ай бұрын
Все всегда показывают но еще ни кто не заварил кратер
@DickTator47
5 ай бұрын
Меня тоже это раздражает. Электроды экономят. Роликов много нужно снять, а электрод один на хозяйстве.
@LaughitOff526
7 ай бұрын
We were taught to hold the rod perpendicular to the axis of the weld.
@user-ux4dy5dm7c
Ай бұрын
Неправильно вас учили. Ведение электрода углом вперед или назад - это способы влиять на температуру сварочной ванны в зоне сварного шва. К тому же сам электрод легче вести углом, когда он касается обмазкой детали.
@urbecordovaconstructions
8 ай бұрын
Y como siempre, los expertos soldadores de computadora diciendo que está mal y opinando que es mejor cordón continuo en materiales delgados
@trystanbernardie2398
7 ай бұрын
Il y a un truc merveilleux en soudure qui s!appelle la penetration
@RobPulson
6 ай бұрын
or you use the right rods and the right technique.... or MIG
@user-il7qr1ui4h
6 ай бұрын
Начинающий,сварщик никому не чего не должен,его учить надо и показывать как делатьэто , а после этого у него практика с теорией.
@albeiromartinez8292
Ай бұрын
Se puede hacer un cordón de inicio sin romper el tubo solo se recarga más el electrodo en el material más grueso que en este caso del video es una varilla lisa
@juanbergamaschi7658
20 күн бұрын
Gracias buen consejo 😊
@user-fr4ei2eu5r
8 ай бұрын
Я, так понимаю, это, показывает, как нужно варить, но в практике, я не встречал таких бестолковых соединений.😂
@andretroll3853
Ай бұрын
SOLDADORES ADELANTE - Mi video se llama - Robotizado con CD4017 , NE555 Pilotos Con esto funciona mucha maquineria solo. Andre
@fmarmorconce
Ай бұрын
De acuerdo al tipo de soldadura y a la maquina en uso
@bradellz7111
Ай бұрын
Why is everything on KZitem a spot weld though? There's a reason they say spot welding isn't very trustworthy.. even if your just trying to stick two pieces of junk metal togeather in your backyard, you should want it to be a safe and trustworthy hold right? :j
@iwin1833
4 күн бұрын
I welded the space 🚀 shuttles for NASA together since the early 80s I know a few things and this guy is correct
@israelreyeshernandez5599
8 ай бұрын
Eso no sirve, mejor baja más el amperaje de tu inversor y solda el cordón completo, bendiciones
@NeuriLee
8 ай бұрын
Ele mostrou que é possível, se vc não dá conta, treine mais, impossível não é, o vídeo prova isso, não seja um incompetente falastrão que fica colocando defeito no trabalho dos outros cara, isso é coisa de mulher
@tbsp3151
7 ай бұрын
@@NeuriLeeMay I ask....are you a welder?
@tbsp3151
7 ай бұрын
@@NeuriLee if there is a test bend I would 100% conform that this will break easily
@tbsp3151
7 ай бұрын
This video is just tacking but not welding
@alvarorodriguez6318
6 ай бұрын
Eso no es truco, se llama saber soldar por eso calientas más el material de los 2 que tiene más masa y no al revés
@thegoat949
7 ай бұрын
95A is to much juice 75 be about wright then you can weld it thick to thin not dot n dab !
@hbwblacksmithing
6 ай бұрын
As a blacksmith and a welder for the past 28 years these are hard to watch this is not how you do it
@_Arsalanka_
2 ай бұрын
А как? Подскажи ученику пож-та
@eliperli3663
4 ай бұрын
Cuando se escucha ese ruido a viento... perforación segura! 😁
@user-yu2pe5zl7x
Ай бұрын
Профильная труба 2мм варится максимум 75ампер , и да , всегда от толстого к тонкому раскачиваешь ванну
@alessandrosantinelli7483
7 ай бұрын
Complimenti, saldi veramente bene 😊
@Gledson.locutor
Ай бұрын
Nossa, to sentindo o cheiro da solda daqui😮
@santiagoortizmartinez6109
Ай бұрын
Perfecto! Muy bien Gracias saludos
@andrzejporeda7281
19 күн бұрын
Super jestem pospawane i bardzo fachowo Pozdrawiam serdecznie. 👍👍👍👍👍
@MarceloGomes-ju4dk
Ай бұрын
Que solda bonita!
@JamesDoylesGarage
7 ай бұрын
I keep learning Thank you :P
@user-ed9oq1oj8x
Ай бұрын
Второй шов делать не надо. Конструкция, если сделать второй шов, крепче не будет. Тонкий металл всё равно не выдержит большую нагрузку. Высота катета сварного шва должна быть равна наименьшей толщине свариваемого металла.
@unclejacksimulations9423
6 ай бұрын
I've been in this industry for over 60 years. I've met with a living heir of John Weld himself. Your work is not galvanized nor combobulated, your bevel isn't chamfered, and your steel isn't compounded. That will not hold
@MacNifty
Ай бұрын
I'm trying to understand why they always tap weld. You should be able to draw consistent lines.
@leandroescalada219
Ай бұрын
Para mirar estos videos debo de usar casco también???
@tony78uk48
7 ай бұрын
Looked ok to me ....but i dont weld nuclear power stations together like some commenting .
@drlira
Ай бұрын
A cuanto amperaje es la primera vez que lo soldas?
@gustavozaremba3373
6 ай бұрын
Que buena costura !
@user-mt8tz6gz4g
Ай бұрын
Не критикую, каждый делает в своём стиле и понимании, но заварил бы разом Меня вообще удивляет как он с таким опытом прожёг профиль
@coulditbe2547
7 ай бұрын
I’m currently in welding school and I feel like I know a little more than the guy doing this I’m on week 2 and my instructor would weld my asshole shut if I welded like this
@InkArtista-nt6zk
6 ай бұрын
😂😂😂😂😂😂
@sklikizos
6 ай бұрын
What kind of rod would he use? 😂
@coulditbe2547
5 ай бұрын
@@sklikizosu would want to lower your amps and go with a 3/32 6010, there is also ways around it as well by dragging the puddle and not dragging the metal, nig and tig is amazing for thin metal but u can do it with stick, with stick it’s easy to burn through especially if your running higher amps
@coulditbe2547
5 ай бұрын
@@sklikizosrod angle is everything to he pointing directly in, if he was smart you would law a thin stinger down then a cap so there is already metal to use underneath
@sklikizos
5 ай бұрын
@@coulditbe2547 whoosh. I was making a joke about the rod to weld your a------ 🤣
@AgusTri-jr7ph
4 ай бұрын
Mantaaap terimakasih atas ilmunya,,,❤
@Antoni_snk
Ай бұрын
Jajaja estas enseñando a puntear PTR? Te podria creer que enseñaras a puntear materiales delgados, pero enserio estas enseñando a puntear PTR?
@amodinho32
6 ай бұрын
It's not necessary that way. You can weld continuously if you send the arc against the bar... The solid size bar can resist the arc
@emanuelalvarez2908
6 ай бұрын
I do only one pass by doing little circles while sliding through the whole line, but rest every couple centimeters so the material does not overheat.
@josemonroy5422
Ай бұрын
Solo que, el condoneo es de izquierda a derecha, y si se puede hacer de corrido , con un poco menos de amperaje
@user-of4rh1fc2e
29 күн бұрын
Показывает электрод, но слишком быстро. Не удаётся разглядеть.
@user-rp5oq4wn5j
Ай бұрын
Сколько людей- столько мнений.Но- есть- правильные,умные,есть- ошибочные и глупые.Учиться- никогда не поздно.Но- ум приложить- вреда не будет.Жаль- прошли времена когда работников просили что- то придумать,улучшить,было НТО,рационализаторы и т.д.
@user-de2dh4qm5d
Ай бұрын
I sucked at sports, so @13 I worked in a garage turning wrenches. But that was 40 years ago. One thing I never could do was stick weld? Gas weld ,braze and Tig and mig. I always had a hard time getting started cause the glass was dark. Someday I'll try again
@user-ro8xj8bc5w
6 ай бұрын
А ведь можно ещё и полярность поменять
@user-ji7sc5dz9g
5 ай бұрын
Зачем ?
@pipipsopian3260
Ай бұрын
KalAu ngelas yang tipis tabel 0,8 Ampernya di posisi berapa?
@some_dude1234
6 ай бұрын
As a former welder, I can confirm that is not the proper way to weld anything.
@p.p.burnell7294
6 ай бұрын
Then explain how it's done.
@JRsVsO
6 ай бұрын
So how would you stick weld a 6013 on thin to thick metal? Gorilla glue?
@marciliosilva2270
6 ай бұрын
Gostaria de aprender a soldar bem assim. Caetité Bahia Brasil
@Andrew-vo2ff
6 ай бұрын
Что за хитрость?
@Kratek-cy4mr3ev1s
Ай бұрын
такие тонкие профили уже давно варят проволкой на полуавтомате
@iga00001
Ай бұрын
он у тебя есть?
@Kratek-cy4mr3ev1s
Ай бұрын
@@iga00001 🤦
@iga00001
Ай бұрын
@@Kratek-cy4mr3ev1s что ты умник? Вот от таких мамкиных спецов и подташнивает.
@Kratek-cy4mr3ev1s
Ай бұрын
@@iga00001 есть у меня и чё?а ты и дальше тыкай фольгу электродом и мучайся
@iga00001
Ай бұрын
@@Kratek-cy4mr3ev1s у меня то есть и не один, и аргон есть, тыкать в жопу пальцем будешь умник, только простому дачнику что полуавтомат брать что бы два раза в год профильки поварить? Балон таскать и вечно заряжать? Потому что с.ка они все травят с крана вечно..Только не пиши про флюсовую проволоку, без газа, говно лютое, а нормальная стоит как полувтомат без газа... так о чем ты ?
@ilsingh9904
Ай бұрын
I don't understand why he chamfered the original tack To me, it weakened the complete structure of the weld, then he turned around and removed the slag on the joint, re-applied the bond, then struck it again...?🤷
@itscoldbro5098
6 ай бұрын
lol you have massive undercut on the top of that weld cuz you would rather change your position than turn the heat down further
@kimhoci7439
6 ай бұрын
saya welder juga..tapi masih banyak belajar..mohon bimbingan nya
@RestauracionesARG
14 күн бұрын
Veo tantas criticas de esta gente ... Amigos la.idea es simplemente unir dos cosas y listo .. No todos soldamos submarinos nucleares dia a dia ..
@samueldominguez8680
2 ай бұрын
Tampoco es para sujetar un puente por el que pasan camiones!!! Así y todo esos puentes hechos por profesionales tambien se caen ...no critiquen
@creat1ve01
11 күн бұрын
Пока смотрел, зайчиков нахватался)
@user-tq1tc9mc6g
7 ай бұрын
О! Как он первый раз проварил - я так умею!)
@marconepassos5381
Ай бұрын
Very well! Good job!
@user-cg8pw5lo9m
Ай бұрын
Нужная информация из этого видео : Резать металл электродом нужно числа меньше, сваривать металл числа больше ...
@Bigbriansc
7 ай бұрын
King of stick stitch welding.
@menitoido
5 ай бұрын
Com eletrodo E6013 é fácil, quero ver fazer com E7018 😂😂
@MaksLzZ
11 күн бұрын
Зайцев наловил, пока смотрел как правильно 😅
@user-pi7lt7yg6z
4 ай бұрын
Until the heat is poured onto the circular metal and then it melts onto the square metal, thus creating a good weld with strong cohesion without any errors
@user-fb3cy2gg1w
Ай бұрын
Чтоб человек осознавал радость полуавтомата😮..
@yhird
7 ай бұрын
Thank you! Great tip. Cheers.
@gs4847
7 ай бұрын
I don't know anything about welding. Why is he using the technique of "spotting" one touch at a time, as opposed to just pulling in a straight line without stopping?
@AGMertzy
7 ай бұрын
He has the current on his machine set too high, which in turn causes too much heat to flow into the workpiece. The force of his welding arc also goes up with that, so it blows holes through the thinner metal tubing instead of welding it. He also did not direct his arc more into the thick piece of steel rod. The rod can absorb more of the heat without blowing out. He could have turned the amperage down, which would have lowered his heat input and slightly lowered the arc force. He then most likely could have welded the joint in a single pass, pulling in a straight line without stopping as you said. Another technique he could have used if he didn't want to lower his amperage, is a motion called whipping. You whip the tip of the rod back and forth in a small controlled pattern without ever lifting the rod. Generally whipping is just straight back and forth in a line. You weld a little bit, whip back about half the length of your weld pool, slowly drag it out as you weld another little motion, whip it back again, drag it out. When you whip back, you are letting the front edge of the weld pool cool down slightly, and when you go forward you are letting the back end cool. It's a method of controlling the heat, so you don't blow through. But whatever you do, you don't want to do a row of "tacks" like this guy did, and then weld over it. The tacks will have a thing called slag inclusions in them. Slag is that layer that he chipped off with the chipping hammer. It will be completely enveloped in metal, and it will cause a serious weak spot in the joint.
@tonirodriguez8931
7 ай бұрын
@@AGMertzyeso mismo estaba pensando entonces eso mismo se ouede hacer tirar de corrido reduciendo amperaje nove
@AGMertzy
6 ай бұрын
@@tonirodriguez8931Yep, pretty much. I will say there are some scenarios where you might need to run higher amps. For example, maybe you only have a rod with you that needs higher amperage to be able to strike and hold a stable arc. If that's the case, set the amps to as low as possible within the capabilities of that particular rod, start welding, and find the whip tempo that keeps the weld pool the right temperature.
Пікірлер: 660