I just did cabinets, semi gloss emerald urethane. After curing for 2 days it was smooth and hard. Definitely not like shark skin. Sounds like they fixed the problem. 10/10 for cabinets. Went with snowbound white
@priceandpride
Жыл бұрын
bless this man for leaving that nasty grease and mess on his cabinet surface for weeks and months!
@LiveNLearn1968
11 ай бұрын
are you a DIY or pro?
@hulk01921
8 күн бұрын
Just painted my cabinets -First step used liquid sandpaper. -Second step 2 coats primed with BIN shellac. -Third step very light sand with 180 grit just to remove little bumps -Fourth 2 coats of Emerald paint.
@coryrobinson806
2 жыл бұрын
I would have to disagree with with it leaving a “rough” surface. I’ve used this trim paint on many jobs and I thought the same thing as first but turned out it was just dust in the air settling. Since this product has a longer drying time than many other paints I believe that when removing masking and/or opening and closing doors allowed that dirt and debris to settle and dry with the paint. I lightly sanded the surface with 320 grit, cleaned and recoated paint then allowed about an hour for the surface to dry before removing masking and it was very smooth almost like a cured epoxy. I could be wrong but this is my opinion on the paint.
@klappenbergersonpaintingha2933
2 жыл бұрын
I appreciate your comments.
@francesj.jenson6698
10 ай бұрын
Thx for your review. Very useful info covered. ❤
@rickmegandrapeau6950
7 ай бұрын
Just shot this out of my 5 stage hvlp with siphon gun thinned 10 percent with distilled water and its smooth.
@thesergeant3524
2 жыл бұрын
Very nice review and very thorough in your testing approach, especially that you didn't rush it and let it properly cure. On my last kitchen project I used BM Advanced and was very very happy with that paint. However, it's impossible to get anymore, same with Emerald. I had a bathroom vanity to do and took a chance on Home Depot's Behr Urethane Alkyd in Satin. Mixed feelings about it. I would be very curious to see how it fairs in your testing.
@nshilling2866
Жыл бұрын
DIY homeowner did a complete renovation used emerald on 13 interior doors using a Fuji HVLP sprayer. 5 years later all the doors still look as they have been freshly painted. Learning curve as with all products but great results.
@klappenbergersonpaintingha2933
Жыл бұрын
Great to hear!
@joshymcdaniel9233
Жыл бұрын
Did u do any “test” doors or trim using Duration? Lots of recent reviews are saying duration is really good also on trim/ INT door I’m debating Duration or Urethane
@crunchyrn
Жыл бұрын
DIY Homeowner, Just repainted (oak cabinets, HVLP sprayer) with this in the semi gloss and while it looks amazing we have the same problem with the smoothness.
@juanjuventino570
Жыл бұрын
There is a big difference between brushing and spraying cabinets I use a titan capspray 105 hvlp and with the emerald urethane semigloss they come out really really smooth
@klappenbergersonpaintingha2933
Жыл бұрын
Yes you are correct. All premium grade paints look amazing when they are sprayed.
@fairamir1
Жыл бұрын
And also if you use mini roller like me @@klappenbergersonpaintingha2933
@mr.kenslifeshop4034
Ай бұрын
What kind of paint would you recommend for a front entry door this is what I was thinking was the Sherwin Emerald.
@lauriebrennan1195
Жыл бұрын
I was just about to buy sw emerald satin for my cabinet remodel. So glad I saw this video! I want a paint that feels smooth. Do any of your other videos address this with suggestions?
@carolynking332
8 ай бұрын
Painted kitchen island 2 yrs ago with this. I would not recommend. Degreased, sanded, primed, brushed and rolled 2 top coats sanding in between. Started to chip after 1 year....I'm not a pro though. Just had kitchen cabinets repainted by a pro this time. Used Renner 2k...hopefully optimistic.
@pinklaura1961
3 ай бұрын
Watched just now, and I am wondering what you would recommend for kitchen cabinets?
@67NewEngland
7 ай бұрын
- So does the Emerald Urethane still dry with that rough texture or has it been reformulated since your review?
@julesgranati5860
2 жыл бұрын
Question about the feel ‘bite’ you described to the finish- how did you apply? The most I felt that way about this paint was when I sprayed it… I ended up realizing I used too small an orifice size on the spray tip… I thought maybe that was the cause, I think when it’s brushed it’s not too bad of a feel for semi gloss at least
@cressdiligent
3 ай бұрын
What's catsup?
@Alan-yd5ng
Жыл бұрын
Why not oil prime instead of the shellac? Nice vid thanks
@donproctor3445
2 жыл бұрын
Im building my own kitchen cabinets shaker style. Going to paint the face frames and doors. Poplar frames and MDF panels. Should I use this paint or the BM Command. I will be spraying them using the Graco truecoat gun.
@jonathanrjacob
Жыл бұрын
Don, how did this project turn out? What paint did you end up using? I am about to embark on the same journey and paint finish is the only thing I’m worried about.
@anishapaul7111
6 ай бұрын
@@jonathanrjacobhow did your project turn out? Which paint did you use?
@scotty362100
Жыл бұрын
115.00/gal in Illinois in July 2023 - and i think it is JUNK! I sprayed with HVLP and it will never harden. After 4 weeks if you sit something on it it will stick to the paint.
@chrisblack6331
8 ай бұрын
in your opinion how much would 1 gallon of this paint cover?
@mwahlert
2 жыл бұрын
Which base did you use for your testing?
@joshymcdaniel9233
Жыл бұрын
Anyone have first hand experience….. I’m debating between the urethane or Duration for interior closet doors/ trim
@larrybryant1234
2 жыл бұрын
How can get a emerald flat paint to a emerald satin paint
@kenmitchell3355
Жыл бұрын
Excellent video!! Do I have to sand between Emerald urethane coats and can I recoat the next day?
@klappenbergersonpaintingha2933
Жыл бұрын
Yes and yes
@allgoodremodelingconstruct1043
2 жыл бұрын
What is the best paint for cabinets
@chrisbraddock9360
Жыл бұрын
I've never had this problem. Did you sand prior and in between coats?
@klappenbergersonpaintingha2933
Жыл бұрын
yes
@priceandpride
Жыл бұрын
why can i see all of the brush strokes on the trim?
@klappenbergersonpaintingha2933
Жыл бұрын
Brushing dosen't have the same self leveling that spraying has.
@bcrou712
2 жыл бұрын
Can I top coat this paint with water based poly, for a high use area
@klappenbergersonpaintingha2933
2 жыл бұрын
Yes you can!
@jovo9000
Жыл бұрын
uhhh if you spray emerald it is very smooth
@klappenbergersonpaintingha2933
Жыл бұрын
Yes, but there should not be a night and day difference between brushing and spraying. I also believe SW is getting the issue resolved.
@morokeiboethia6749
Жыл бұрын
Do you use shellac-based primer on cabinets because of shellac's stain blocking attributes? Also when something says "stain blocker" does that mean keeping stains that are under the primer coat from bleeding through as well as keeping things above or on the stain blocking coat from being able to permanently stain the paint? .... in simple terms is it only blocking stains under the coat or is it blocking under and above?
@klappenbergersonpaintingha2933
Жыл бұрын
I use Shellac because it fuses with lacquer finishes that are on the surface of kitchen cabinets. Stain sealer blocks old stains from penetrating.
@Painfulwhale360
Жыл бұрын
@@klappenbergersonpaintingha2933 what shellac primer do you recommend for this emerald urethane?
@fairamir1
Жыл бұрын
Just takes too long to dry for cabinets
@edferguson1388
2 жыл бұрын
Going to brush/roll BM Advance on my kitchen cabinets, but was considering brush/roll SW Emerald on interior MDF doors & MDF trim due to faster dry & cure time. Your thoughts? Go with BM Advance all the way?
@klappenbergersonpaintingha2933
2 жыл бұрын
Hi Ed, Command is equally as durable as Advance and costs less. It also dries in about 15-30 minutes. It self levels about the same too. If you roll make sure you back brush to knock off the roller nap. I invite you to subscribe so you can here more product reviews and tips and tricks. Thanks!
@Avital4414
2 жыл бұрын
@@klappenbergersonpaintingha2933 does one of them brush/roll easier than the others (meaning is if easier to avoid brush marks)? Thanks for a great video.
@klappenbergersonpaintingha2933
2 жыл бұрын
The trade off is a slightly smoother finish to the touch with Advance or quicker recoating with Emerald. That's the only significant difference.
@klappenbergersonpaintingha2933
2 жыл бұрын
@@Avital4414 Very very similar. Slight edge to Advance but nobody will see the difference.
@Avital4414
2 жыл бұрын
@@klappenbergersonpaintingha2933 thanks for another terrific video, and for a very very helpful reply.
@williamsmith9026
2 жыл бұрын
I just did a whole building with 5 apartments. I used this paint (semi gloss) on all of the trim, doors sills and bathroom ceilings. I thought it could have had a touch more slide when feeling it but, didn't dwell on the topic I just sprayed some cabinets black in the satin. Primed with extreme block oil and sprayed with one heavy pass black onto the white primer. Im letting the doors cure a bit before they go back on but here's a walkthrough after I was done spraying if you want a chuckle. Mild potty mouth here and there but, it did not have one curtain call... also Im not a video guy so no nagging on the quality.. Ill follow up when the doirs are back on. This stuff feels as close to a factory finish as you can get in the field imo.... kzitem.info/news/bejne/on-f0YOeb2Vkkn4
Пікірлер: 54