Intersting technique. I would be scrared of that hexagonal bar.
@cdrive5757
Жыл бұрын
One would have to assume that if you're watching machining videos this subject interest you. At the time of posting my comment there are a mere 14 comments, yet there are 6,900 views! Does that mean that there are 6,886 aspiring machinists that find this hack commonplace? When the Lathe (only) is your focus this hack is brilliant! At the very least it's definitely not commonplace! This certainly deserves far more that the 294 current likes! The term "Hack" carries negative connotations but I'm adding my LIKE because this method deserves a hell of a lot more! Wakodahatchee Chris
@Yantoo
Жыл бұрын
Thanks brother ♥️🙏
@449ste33
10 ай бұрын
Interesting but ever had one of those spacer bars pop out at you when you start up!? Centrifugal force is a wonderful thing. 😮
@Tom-xn7zc
Жыл бұрын
So this is how my out of square (or hex?) Aliexpress hexagon ER32 collet chuck was made. This explains so much! Finally I understand how they managed to screw it up so incredibly bad.
@edwardhugus2772
Жыл бұрын
Must have used the wrong plastic "machinist" triangle...I actually moved my head when he started that lathe with that dodgy "precision" setup jig.
@Tom-xn7zc
Жыл бұрын
@@edwardhugus2772 Haha I was hiding underneath my desk within half a second when he first started that setup.The precision machinist triangle he uses is not even the worst issue.. those thing can be pretty close to accurate from time to time.
@edwardhugus2772
Жыл бұрын
@@Tom-xn7zc And I cant figure why he faced everything from center to edge...sure, it works, but I wasn't taught that maneuver.... and his finish was horrendous. I'll bet his prints for the part were drafted in crayon.
@Tom-xn7zc
Жыл бұрын
@@edwardhugus2772 He tried working from center but his guesstimates were pretty far from center. At least halfway through he started using a backstop in order to stay on dimension so perhaps his next piece will be more accurate. The crayon drawings part of your comment had me laughing out loud, thank you for brightening up my day.
@edwardhugus2772
Жыл бұрын
@@Tom-xn7zc Happy to make you smile, have a wonderful day!
@user-sb7dw4yk5b
Жыл бұрын
Корявенько конечно вышло ,но предпосыл понятен будет многим ))) думаю в видео автор не придерживался линейных параметров, а просто на скорую руку показал краткий смысл изготовления шестигранника на токарном ..., молодец, учишь начинающих , хотя в этой процедуре нет ничего нового )) тема весьма затертая)
@user-zp2hp5ek5o
Жыл бұрын
Надо ещё было вам добавить, что в случае если деталь вырвет, так как она держится не очень надёжно, то токарь (если останется жив и здоров ) испытывает очень яркие и глубокие положительные эмоции. Помню когда слесарь попросил отрезать кусок от резца высотой 32 мм, то от вибрации, так как работа на удар, кулачки приотжались ( а у резца стороны оказались не параллельны, это я уже потом выяснил)... и потом я выставлял переднюю бабку. И благодарил ангела -хранителя, видимо тому пришлось здорово поднапрячься.
@tylervandewal2775
3 ай бұрын
@@user-zp2hp5ek5o That sounds chaotic
@alexanderkoslowski7813
3 ай бұрын
Ничего нового и особенного..😊
@josemacielzamudio1773
Жыл бұрын
Vamos arriba hermano Messin excelente un Abrazo para ti y todos los hermanos Indoneses. ❤❤
@dksmith605
Жыл бұрын
Nice. I would recommend you invest in a dead-blow hammer though, they really are the best tool for knocking the part hard into a chuck or machine vice, perfect for getting the part sitting hard against a parallel strip. If you can't invest the money to buy one (there are some reasonably cheap ones) then invest some time and scrap to make one. It's just a soft faced hammer with a hollow head which is filled mostly full of steel or lead shot. The shot provides a second impact that helps prevent the part from bouncing back. Every machinist needs a dead-blow hammer, it was one of my first projects as an apprentice.
@mito7212
Жыл бұрын
Gracias, siempre se aprende
@user-sw7pn2en2i
Жыл бұрын
Хордите на шестогама никога по този начин няма да са еднакви,ти на фреза с деференциал пак трудно ще ги получиш камили ,по този начин на струг.
@mihalygedo1010
9 ай бұрын
van ilyenem ,mert vett egyszer a fönök magának,eltört a müanyag feje,és mérgébe bedobta alomok közé én kihalásztam és müanyagbol csináltamrá betétet,és elhoztam haza mert ,ha meglátta volna elvette volna mert igy jol hasznáható ujra.ö meg vett magának ujra egyet, késöbb meg lett egy amühelyfelszerelésbe
@frankthieme8724
Жыл бұрын
Your work is so effective with simple means.✊️ Frank 🙋♂️🇩🇪
@Yantoo
Жыл бұрын
Thanks Frank ♥️
@black_sheep_fab9411
10 ай бұрын
Brilliant. May not be to the .0001 but would be great for a shade tree guy like myself putting flats on a turnbuckle or something. Love it
@jimwinchester339
Жыл бұрын
Yes, the "trick" to making a hexagon is to use your handy 60-degree angle piece. Who would've thought of doing that? Very original.
@ctrlz4439
9 ай бұрын
For beginners/hobbyists in machining wihout a lot tolling it is a valuable idea how to make things.
@jimdrechsel3611
10 ай бұрын
Very interesting. Enjoyed watching. I was a machinist for years but never saw this.
@kostia75
Жыл бұрын
Спасибо за метод, буду использовать! 👍👍👍
@williamrojas4794
Жыл бұрын
Excelente amigo, muchas gracias por compartir su experiencia y conocimientos
@MattysWorkshop
Жыл бұрын
Gday, that’s a simple way to form a hex, great job mate, cheers
@alonsorubio6036
Жыл бұрын
Excelente trabajo... Y explicado en poco tiempo...
@michelfrance75
Жыл бұрын
You should explain how you proceed to obtain a regular hexagon with 6 identical faces and whose axis coincides with that of the starting cylinder.
@wizrom3046
Жыл бұрын
He doesnt. This is the equivalent of "bucket chemistry" in machining. The best you get is a HSO 😁
@oldfarthacks
Жыл бұрын
He makes contact and then turns in a specific distance from that contact point. The first face is at a random place in space, the 2nd and 3rd are set by the protractor. The next 3 are just by spacing against the bar up against the face of the chuck. Straight forward but still very smart.
@elduderino1329
11 ай бұрын
It is pretty self explanatory to me.
@toddz8579
11 ай бұрын
What’s not clear to me is how far into the piece do you advance the cutter when creating the faces of the hexagon, without doing the math. I must be missing a detail in the “bucket chemistry” mentioned here 😉
@wizrom3046
10 ай бұрын
@@toddz8579 yep. You just cut them all to the same depth. That is all you need for a hexagon, 6 cuts to the same depth, and indexed somehow in 60 degree steps.
@user-ds6qf2mv1q
Жыл бұрын
Ух мне аж страшно стало, вращающийся ломик, а там еще и ключ патрона в станине между ног болтается... Ну вы поняли
@sakyra3012
Жыл бұрын
ага после ключа выключил и в игнор чудика.
@hosseinjahangard336
3 күн бұрын
Fantastic sir , what kind of carbide tool you are using ? Many thanks
@jagannathgiri6179
8 күн бұрын
Super idia bro
@user-nc1ic6yx8m
10 ай бұрын
А вот за прикрытую от абразива станину - респект !
@dannymullane9252
5 ай бұрын
Absolutely great thank you
@machinist1
Жыл бұрын
Nice video
@milanzizka4636
Жыл бұрын
Šikovné, moc pěkné.
@pattwidale4045
Жыл бұрын
Such good information. Thank you very much.
@Yantoo
Жыл бұрын
Thanks for watching brother Twidale
@jackkallemdjian3945
9 ай бұрын
Never seen this before ,nice
@mircospignoli3738
Жыл бұрын
congratulations you make everything simple
@Yantoo
Жыл бұрын
Thanks brother Mirco ♥️
@icusawme2
6 ай бұрын
Stuff I don’t even think about doing,thanks
@Bianchi77
Ай бұрын
Creative video , thanks you :) Do you have the technique on making a spiral drill bit ? thanks
@Yantoo
Ай бұрын
Saya akan mencoba memikirkan teknik membuat mata bor spiral
@Bianchi77
Ай бұрын
@@YantooThanks, common drill bit, we use daily :)
@beest921
Жыл бұрын
Very nice!
@giridharimandal5492
Жыл бұрын
Nice method❤
@leonardimedke3368
Жыл бұрын
Parabéns 👏👏👏👌. Brasil
@m.shahidkhan
9 ай бұрын
Wow 🍂🌴🌴🍁🪴🌲🌲🌺🌺🌺🌺💯🌱💐💐💐💐💐💐🍄🍓🍓🌷🌹🌹🪻🥀👍👍☘️🍀🦋🍃🍃😍🍨🍀🍀 good job
@davidzertuche910
8 ай бұрын
Muy buena idea, que buen ingenio
@scottthomas5999
Жыл бұрын
Very creative and clever.
@Yantoo
Жыл бұрын
Thanks brother Thomas
@Wallerschreck
8 ай бұрын
wie lange hält eine Ladung des akkus?
@faysalkadi896
Жыл бұрын
School supplies seller rejoices with his favorite customer
@martinnorbeck4657
Жыл бұрын
great vid
@mr_orionmr_orion4620
Жыл бұрын
Зачем допиливать болгаркой? Длины резца не хватило? Можно же оставить совсем тонкую шейку и руками отломить. Если уж не хочется дорезать...
@glaicogoetten6906
Жыл бұрын
Ótimo vídeo, parabéns
@arduinomaquinas
Жыл бұрын
Very cool video 🇧🇷😉👍👏👏👏👏
@Yantoo
Жыл бұрын
Thanks brother ♥️
@alessandroandrenacci2372
Жыл бұрын
... wonderfull ...
@fredyrahmads
6 ай бұрын
Good idea😃
@vindicator05
9 ай бұрын
And this, little one, is where the little steel sponges come from...
@2011alhambra
9 ай бұрын
Thank you for No 'Muzick' noise !
@bobjimenez4464
Жыл бұрын
nice trick : )
@lolatmyage
Жыл бұрын
Clever!!!
@tornerongkamayvlog1009
Жыл бұрын
Idea yang bagus kawan goodluck
@alirezakavian
6 ай бұрын
عالی بود ...ممنون بیننده ای از ایران
@TrPrecisionMachining
Жыл бұрын
good video mekanik mesin
@user-zw4jd4wm8m
Жыл бұрын
Молодец. Знаешь что делаешь.
@kotkotikow
Жыл бұрын
А зачем изготавливать шестигранник? Можно его купить и не тратить драгоценное время
@JarppaGuru
8 ай бұрын
yes but what size and are they all equal from centre. and its cheaper buy that size hex scrap part lol
@marcosboscatto7590
Жыл бұрын
Interessante, porém perigoso! E o avanço for alto e a ferramenta travar na peça, ela pode se soltar e acertar a cabeça do torneiro. Serviço específico para fresadora e não para torno !!!
@mito7212
Жыл бұрын
Gracias por el aporte
@juanignaciocaino
Жыл бұрын
Potentially dangerous, imprecise, sloppy... exactly my style! lol. Sometimes these techniques are the best.
@bulletproofpepper2
Жыл бұрын
Thanks for sharing.
@richarspaiva5973
Жыл бұрын
Buenas la escuadra que usas es de 30 grados
@user-cy6oz3sk8o
3 ай бұрын
Отказывается так просто👍
@charleskutrufis9612
Жыл бұрын
Thank You
@JoseEmiloAcostafernandez-yh8bq
11 ай бұрын
Buen trabajo
@mikestevens8046
Ай бұрын
You dont ever leave spacers like that in the chuck. WITF are you thinking????
@olivvapor4873
Жыл бұрын
Don’t you destroy the tool machining the piece thus ? ...
@javierclemente2420
10 ай бұрын
Exelente trabajo
@Yantoo
10 ай бұрын
Terimakasih saudaraku ♥️
@Utomoteknik
8 ай бұрын
Wow kueren Om
@francometalo
Жыл бұрын
très bien 👍👍
@ucuy3706
Жыл бұрын
Khi bạn ko đủ máy móc thi việc đó thật tuyệt vời
@ing.mecanico4132
6 ай бұрын
Buen video saludos
@Anrufbeantworter
10 ай бұрын
Unfortunately, he forgot to take a measurement somewhere, and then turn half of his hex width from each face. Then the outer contour would be good enough for a nut.
@christianheidt5733
3 ай бұрын
A good machinist will always make the parts, no matter what machines or tools are available to them.
@tokarz5379
Жыл бұрын
Dobra robota!
@amazingthingofficial2923
Жыл бұрын
Nic❤❤❤
@muneshshelar2530
6 ай бұрын
Nice
@luizboiadeoliveirapintogon3141
7 ай бұрын
Muito bom.
@supericard1813
8 ай бұрын
Génial merci ca peut servir. Même si je suis fraiseur 😉
@user-bt5tk1th5o
Жыл бұрын
ยอดเยี่ยมๆ
@t.b.8599
8 ай бұрын
très bonne technique mais très dangereuse, si par malheur il oubli la barre en aluminium il aura le crane fracassé.
9 ай бұрын
Super !😂
@andrel9317
Жыл бұрын
🙈 das tut weh beim zusehen, so viele schläge aufs Werkzeug und Vibrationen die der Maschine und deren Lager nicht gut tun. Bevor ich so mit einer Maschine und dem Werkzeug umgehe da Feile ich lieber per Hand und mit nen Winkelschleifer. Auch wenn die Technik auf den ersten Blick schlau ist, auf den 2. Blick kann man als Fachmann nur mit den Kopf schütteln. Grüße von einem Deutschen MAF Metall und Kunststofftechnik.
@seyedamirkhakzadian7794
10 ай бұрын
وقتی پشت دستگاه تراش میایستی یاد بگیر آچار را روی دستگاه رها نکنی و وقتی میشه یک شش ضلعی به این شکل خرید شما نباید تمیز کردن و بریدن و ... رو به ما نشان بدید
@user-zv3hj4dm7g
11 ай бұрын
А зачем? Для этог осуществует фрезерный станок.
@JoBouten-ko1fc
Жыл бұрын
Ophouden met die mailtjes
@user-dj1tf7rx6u
9 ай бұрын
Tronconnage l'outil a l'envers et dressage de face outil a 45degré
@robertfaizullin4712
Жыл бұрын
آفرین!
@Sivojar
Жыл бұрын
Научись сначала резцы точить и отрезать 😅
@salvadorvaldivia7010
9 ай бұрын
Eso ases cuamdo no tienes una fresadora y no tienes mido de darte un madraso
@user-zy9mi8be1c
9 ай бұрын
Деление окружности на 6 частей ,проще некуда,грань равна радиусу.
@Zeela47
5 ай бұрын
Hearing and seeing the word lathe is scaring maybe because of the russian accident
@ks-ek4of
Жыл бұрын
👍👍👍👍
@aliabiary178
9 ай бұрын
چرا ویدئو خرابه نشون نمیده
@user-zs5ek3gr2p
10 ай бұрын
厲害
@mariuszg3965
Жыл бұрын
👍
@bimbim2000
10 ай бұрын
Mantap euy
@abdoallahalsayedalihamza6649
Жыл бұрын
تسلم ايدك
@anggagemarchaneltrabas8460
11 ай бұрын
Kalo huruf U gini gimna bang bbubutnya
@the_machinist544
Жыл бұрын
❤❤❤
@moazzamali8452
Жыл бұрын
Ok sir
@fabricecarlier7791
9 ай бұрын
👍👍👍
@gtmtnbikr
Жыл бұрын
You finished parting the piece off at 1:15 with a powered cut off wheel for why?
@oldfarthacks
Жыл бұрын
His chatter was getting too bad. A problem with the tool or the tool post, rigidity is the issue.
@bobturnbull18
Жыл бұрын
Probably no more stick out available on the tool. At the small remaining diameter chatter should not be a problem.
@celioribeiro8421
Жыл бұрын
Bom, vc usou o mesmo procedimento que eu fiz, muito bom.
@Yantoo
Жыл бұрын
Terimakasih saudaraku ♥️
@gheumann
9 ай бұрын
Very clever. But having that bar stick out past the chuck is just a stupid unnecessary safety hazard.
Пікірлер: 178