Thanks for the info I was wondering about this conversion. Just ordered one myself.
@30aught6
3 жыл бұрын
that fuxn' cricket
@6.0biggie26
4 жыл бұрын
Thank you👌🏿 alot of good info
@nickonickster1
3 жыл бұрын
I got one from dennys driveshaft...went from 4l60 to 80
@ivanbarajas5471
7 ай бұрын
The slip yoke I have that came with the 4l80e has about 1/2 inch gap. It won't set on the lock.
@cristianjantes7453
5 ай бұрын
Did you figure it out I’m having the same problem
@ivanbarajas5471
5 ай бұрын
@cristianjantes7453 took it to driveshaft shop they put a different style yoke.
@cristianjantes7453
5 ай бұрын
@@ivanbarajas5471 what yoke
@ivanbarajas5471
5 ай бұрын
@@cristianjantes7453 slip yoke on the drive shaft in to the transmission
@josevenegas2319
3 жыл бұрын
Ok, I got the part number for the u joint (thanks)... but can u give the whole layout as far as all upgrades and changes to run a 4l80e behind a 5.3 engine? I got a 2002 Silverado single cab shortbed. I have the 4l80 already but haven't installed it, I bought a stock used driveshaft as well but don't know what yoke to get, my original driveshaft,yoke broke off along with all the back end of my old 4l60 tranny I had in it... so I went ahead and bought a used stock 4l80 and a drive shaft...BUT.... I now realize I need a different flex wheel, fluid lines change, wiring harness changes, yoke changes, .... I'm guessing crossmember too... sooo, I need all specs and part #s if u can, total life saver! And need some reassurance that I CAN use the stock length driveshaft I already bought... help please
@JMSAUTO
3 жыл бұрын
I have a circle d direct bolt converter with stock 5.3 flex plate. Stock 4l80e yoke adapted with above ujoint. I cut the stock cross member, moved center section back to 4l80e mounting stud and welded it up. Only thing else required is a a 4l60/65e to 4l80e adapter harness from pcm of nc. My truck is an extended cab with 2 piece driveshaft and carrier bearing. I think speed engineering makes and swap crossmember if you don’t want to mess with making one.
@josevenegas2319
3 жыл бұрын
@@JMSAUTO what about the fluid lines? Did ur old ones work by rebending them or something? Or did u have to buy new fluid lines to fit and reach?
@JMSAUTO
3 жыл бұрын
@@josevenegas2319 stock ones worked just took some massaging
@josevenegas2319
3 жыл бұрын
@@JMSAUTO thanks... I will be buying a stock 6.0 flexplate since the 4l80 has a stock torque converter... try working the lines to plug into the 4l80's inserts....I will be buying a prefabricated crossmember....that just leaves the yoke and the wiring.... I'm guessing the stock 4l80 yoke should do....? Still unsure if driveshaft will sit right.
@bowtiebuilding
4 жыл бұрын
Thanks for the video, very helpful. What did you do about your dipstick?
@JMSAUTO
4 жыл бұрын
Baylen Lee used the stock dipstick just had to bend it a bit to clear the firewall
@richardkauffman5169
5 ай бұрын
Got a "700R4" driveshaft from a 90' c1500 trying to put a 4l80e yoke on it. would this part fit? or how do i go about finding the right U-Joint for my application
@salbuildz441
4 жыл бұрын
This is going to sound odd , I bought the same u joint as in this video , the two ends that go to 80e yoke and way to small
@JMSAUTO
4 жыл бұрын
Salvador Balandran that is odd. My trans was a 2004 I believe with the driveshaft from my 2005 Silverado mating up using this I joint with no issues.
@miguelresendez2283
3 жыл бұрын
Same here
@egghead1093
4 жыл бұрын
Do you know what the transmission came out of so we can identify the yoke? I have an 01 extended cam 2wd and looking to get the 80. Thank you for sharing your knowledge. Much appreciated.
@JMSAUTO
4 жыл бұрын
egg head it was out of a 2004 express van
@juanclarissmajalca1277
4 жыл бұрын
Do you have a part number for the yoke? I have one from a 2001 4l80e truck and I can't find a u-joint to fit my factory 2 piece shaft
@rubenvillalobos15
2 жыл бұрын
Did you find the part number?
@GreatestHITS26
3 жыл бұрын
I’m swapping my 4l60e to a built 4l80e on my F body firebird trans am. What driveshaft should i use? since the 80e is longer then the 60e
@843slick
Жыл бұрын
What about the back end u joint
@JMSAUTO
Жыл бұрын
Stock
@randy1ization
Жыл бұрын
do you know if someone makes a slip yoke repair sleeve for a 93 chevy c1500 truck driveshaft.. the one that goes into the transmission tailhousing., mine is worn., thanks
@JMSAUTO
Жыл бұрын
No idea
@randy1ization
Жыл бұрын
@@JMSAUTO did some research, they do make one, but they are not cheap., around 45. bucks.,
@anthonydoud
Жыл бұрын
Will this work for the pinion yoke I have a 4l60e drive shaft and I just bought a rear end with 373 gears from a z71 but it has the tabs on the inside of the pinion yoke with the bugger u joint
@JMSAUTO
Жыл бұрын
Not sure I used all my stock size stuff there
@anthonydoud
Жыл бұрын
Thanks man I’ll give it a shot!
@ch.i.c.o5922
2 жыл бұрын
So what was the point of doing this swap? I'm having a clunk on my truck some said is the yoke .
@JMSAUTO
2 жыл бұрын
The stock ujoint won’t work in the 4l80 yoke
@alexsperanza1501
4 жыл бұрын
Hey, Did you ever end up modifying the yoke as you said? or did the th400 yoke fit perfectly fine
@JMSAUTO
4 жыл бұрын
Alex Speranza I used the stock 4l80e yoke with the adapter ujoint and didn’t have to cut it down at all. I have an extended cab so it’s the 2 piece drive shaft with the carrier bearing
@rekburtbudgetbuilds
2 жыл бұрын
So i wonder if this will work for a 4l80 driveshaft i want to use a 4l60 yoke with??
@JMSAUTO
2 жыл бұрын
Yes it should
@frankdatank7751
4 жыл бұрын
Good documentation!!! What truck is that going on, and is it extending cab? Also what the part number or nake of toke you used, Thanks
@JMSAUTO
4 жыл бұрын
Frank da Tank it’s in a 2005 Silverado 1500 ext cab
@frankdatank7751
4 жыл бұрын
Thanks, I bought it and put it on the yoke ,but it did not work on the 97 c1500 side. Its a 1 1/8 and the older model takes a 1 1/16 cap, no biggie Ima figure it lol
@memphis901vet2
4 жыл бұрын
I have a 2004 single cab, and I’m preparing to do the same swap. I have a one piece driveshaft, do you think this setup will work for me?
@JMSAUTO
4 жыл бұрын
Whip_Doctor yes it should be the same. The only difference is that I have a carrier bearing on my driveshaft so it allows for a bit of play. Once you get the new ujoint and 4l80e yoke mated to your driveshaft put it in the trans and make sure it slides back out atleast .250 to .375 inch towards the rear differential.
@memphis901vet2
4 жыл бұрын
Justin Silverado524 i ordered a stock 80e yoke, but it looks nothing like yours. Do you have a part#
@JMSAUTO
4 жыл бұрын
I do not it came with the trans when I bought it
@joe2guns
3 жыл бұрын
Is this pretty much the same idea for a ls1 car with 4l60 changing to 4l80 swap i couls use this same one or woukd i need a diffre t one
@JMSAUTO
3 жыл бұрын
I can’t speak truth on that never done it but if I had to make an educated guess I’d say yes
@joe2guns
3 жыл бұрын
@@JMSAUTO sweet yea ill look into thanks alot
@javierespinoza6551
4 жыл бұрын
From where to where are you measuring the yoke?
@JMSAUTO
4 жыл бұрын
Javier Espinoza on an extended cab driveshaft after it is mounted and inserted into the trans.. from the end of the yoke to the first ujoint. Been driving it like that for a few months now without any issues ?
@bryanj4811
4 жыл бұрын
With this you don’t have to get the driveshaft cut anymore correct?
@JMSAUTO
4 жыл бұрын
Bryan J in an extended cab truck that is correct. No cutting was needed
@bryanj4811
4 жыл бұрын
Justin Silverado524 I have a single cab do you think I’ll get away with it?
@JMSAUTO
4 жыл бұрын
Bryan J I cannot be sure on those mine has a 2 piece driveshaft
@6.0biggie26
4 жыл бұрын
I plan to on doing to swap this weekend. I also have the extended cab but I have a 6 in flip kit. Do you think the stock drive shaft will still work??
@JMSAUTO
4 жыл бұрын
Clarence Perkins yes I also have the 6” flip
@slaskey
2 жыл бұрын
Did your driveshaft fit our did you have to cut it
@JMSAUTO
2 жыл бұрын
It fit
@slaskey
2 жыл бұрын
Is there a certain yoke I need
@JMSAUTO
2 жыл бұрын
Yea the one in the video
@207shenanigans
2 жыл бұрын
Did you have to shorten your driveshaft ?
@JMSAUTO
2 жыл бұрын
No
@207shenanigans
2 жыл бұрын
Is the 80e yoke working fine? Did you shorten it ?
@JMSAUTO
2 жыл бұрын
@@207shenanigans yes it works great I have roughly 3000 miles on it without an issue. No I didn’t shorten it
@onebadgto5460
4 жыл бұрын
So the driveshaft you have from the original thruck what yoke style is it 1330?
@JMSAUTO
4 жыл бұрын
Stock driveshaft with the 4l80 yoke adapted to it using the ujoint in the video
@dominicrose3991
4 жыл бұрын
By using this particular yoke, does this bypass the process of having to shorten the driveshaft
Пікірлер: 69