Great and helpful video as I am about to have to do this. I had a stud snap while driving in my Harland sharp rockers. I’m just beginning to learn about how to build engines and work on them internally. Thank you so much again.
@jamesrene9378
2 ай бұрын
You explain soooo simple thank You brother 😊
@marcadominguez
4 ай бұрын
Nice engine and great video
@DentedDiesel
19 күн бұрын
Should I still be able to spin the push rod after it's locked it?
@ThisOldFarmShop
19 күн бұрын
You may be able to spin it, but you should encounter a good bit of resistance 👍
@coxkevin1
Жыл бұрын
nice thanks
@brianmckay3354
5 ай бұрын
Once tightened to the half turn past zero lash, should there be any ability to spin the pushrod? Sorry for the newb question and great video btw!!
@ThisOldFarmShop
5 ай бұрын
Thanks for the question! At that point, it should not spin freely. You may still be able to spin it if you can get a good grip on it. 👍
@brianmckay3354
5 ай бұрын
Awesome, thanks for the quick reply! I'm new at adjusting these and have gone from one extreme to another in over and under adjustment. Just trying to hone this fox in as it hasn't been running since before I bought it.@@ThisOldFarmShop
@ThisOldFarmShop
5 ай бұрын
Let us know how it turns out!! @@brianmckay3354
@lldjslim
Ай бұрын
Do you do this in the engines firing order
@ThisOldFarmShop
Ай бұрын
That would probably be the quickest. 👍
@lldjslim
Ай бұрын
@ThisOldFarmShop Thanks for responding. Also, is this the same method you use for pedestal mount non-roller rocker arms
@ThisOldFarmShop
Ай бұрын
The pedestal mounts don't usually need adjustment, but if you do have to adjust, it's with shims
@ezebattle
Жыл бұрын
Do you have to go halfway down or just when you see the valve start to come up
@ThisOldFarmShop
Жыл бұрын
For the exhaust: You want to turn the engine until the intake valve fully opens then goes to halfway closed. At that point you adjust the exhaust. For the Intake: turn the engine until the exhause valve is just starting to open. Now adjust the Intake. Hope that helps. Thanks for watching!
@Achurro178
Жыл бұрын
Can this process be done the same way on each piston no matter the firing order?
@coxkevin1
Жыл бұрын
summers coming
@benjihester7455
Жыл бұрын
What’s the torque spec
@ThisOldFarmShop
Жыл бұрын
These were 25 foot pounds.
@jeffsedlick2978
8 ай бұрын
Can this method be done to adjust them with the intake still on?
@ThisOldFarmShop
8 ай бұрын
You could do it with the intake on 👍
@timsimons8946
5 ай бұрын
So mine is making some noise and was interested in doing this. Can I just take Valve cover off ? I did just change oil.and 10w30 motorcraft did quiet it down some but still making some noise. Rattling noise.
@steveapplegarth4577
Жыл бұрын
does it really matter where at on the base of the lobe you tighten the rocker arm?
@ThisOldFarmShop
Жыл бұрын
I would say as long as you know the valve is fully closed, you're good to go 👍
@steveapplegarth4577
Жыл бұрын
@@ThisOldFarmShop ive sorta just put my finger on the lifter, til it moves, back up til it moves again, then just split the difference.
Пікірлер: 26