Very clear demonstration of Myford cutting processes. Thanks.
@prof-rieg
2 жыл бұрын
You are welcome!
@fasousa4798
2 жыл бұрын
I have a S7 and i have never seen that taper attachment until now. Thanks for sharing
@prof-rieg
2 жыл бұрын
You are welcome!
@pcka12
5 жыл бұрын
You have repainted your Myford! Have had two ML7 over the years (both lost to me now as a result of ‘associating’ with women so now reduced to an ML4 picked up on eBay)
@prof-rieg
5 жыл бұрын
Indeed, those Myfords are beautiful machines! Very british and very good.
@davidbawden6567
6 жыл бұрын
Beautiful lathe, and thanks for sharing your techniques...
@prof-rieg
2 жыл бұрын
Many thanks - you are welcome!
@johnswilley6764
4 жыл бұрын
Great demo, thank you.
@Hereford1642
Ай бұрын
At 16:20 you say that a very small feed is added and hence mainly the left edge of the cutting tool cuts. I think this is not correct. If you setup the topslide at the appropriate angle for the thread then the tool will cut on the left edge. It is not possible to tell from your video whether this has actually been done since no wide enough shot is shown. Anyway, it is the angle of the topslide and not the depth of cut that determines which side or sides of the cutter is active.
@JamesChurchill3
4 жыл бұрын
Damn it feels good to be a gangster.
@jasonrichards9330
3 жыл бұрын
Glad I wasn't the only one who caught it.
@alanstapleton3818
5 жыл бұрын
taper turning attachment is still available from myford uk at about £350
@prof-rieg
2 жыл бұрын
Yes, I know.
@fcbarca1012
7 жыл бұрын
Tolles Video. Ihr macht das echt Klasse. Immer informativ und locker gemacht. Aber ich habe eine Bitte: "Vanishing Horizon". Diese Musik passt besser zu dieser dynamischen Art von Lehrvideo.
@prof-rieg
7 жыл бұрын
Danke! Machen wir, wenn es zum Video passt.
@stratking82
2 жыл бұрын
Yuhuuu. Wegen dem Lied schaue ich manchmal ältere Videos vom Kanal weil ich nicht wusste wie es heißt. Jetzt schaue ich nach einer myford drehbank weil ich eine kleine gute Anfängerdrehbank suche und stoße auf den Kommentar. Matthias, das war ein toller Vorschlag und siper dass er auch umgesetzt wurde, ich liebe das Lied:-)
@TheVist7
4 жыл бұрын
Hey. Can You tell me why at 5:40 the indicator is showing 1.50 at starting postition? shouldn't it be 0?
@davidwrighton3914
5 жыл бұрын
next time ---get the tool to cut and not tear
@spidersinspace1099
5 жыл бұрын
Oh my God, that music was so obnoxious I had to stop watching after the first couple minutes.
@deaniweenie
4 жыл бұрын
Agreed. Dreadful music. Why not have the machining sound? I had to watch with the sound off
@lesterbeedell9725
4 жыл бұрын
Would be better without the B awful music, I couldn’t watch it!
@davidwrighton3914
5 жыл бұрын
kill the crappy sound track ---we came to watch ---not listen
Пікірлер: 26