Air to gas ratio video is very good aur aapka explain karne ka andaz bahut achha hai
@askarindamroy
Ай бұрын
Very Informative video. 😊
@dnyaneshwarmane4253
2 жыл бұрын
Sir very nice video..
@yatindraankur1048
2 жыл бұрын
Very nice video sir
@avadheshsingh4697
7 ай бұрын
👍 bahut acha video hai sir connection diagram bhi batay
@syedhassanali9330
Жыл бұрын
Thank you very much sir, very informative video and please tell me its integer and real value
@dwarkeshpatil778
2 жыл бұрын
Perfect and very usefull in industry
@rohitpandey6279
3 жыл бұрын
👌👌 useful video ♥️
@iu665
11 ай бұрын
Hi sir video is very helpful for us to understand about gas to ratio.. sir hope for a video on lpg burner automation like temperature, ignition, flame sensor, air to gas mixing system And how to control two burners individually with one controller.. it will be very important to us sir
@hemantkumarnayak7472
2 жыл бұрын
very much happy to see u back sir, always i am waiting for ur new video
@deepakshukla7290
3 жыл бұрын
V good video for concept clearly
@nageshpandey5333
3 жыл бұрын
Learning a lot from the video
@sumeetlalAjaiswar
3 жыл бұрын
Thanks sir for such knowledgeable video.. 🙏🙏
@mubarishussain3696
2 жыл бұрын
Fantastic. Please make more videos. Appreciate your content
@sohommajumdar6272
3 жыл бұрын
Great to see you back
@sahibrehman5564
3 жыл бұрын
Sir plz upload mor videos about burner's
@pankaj1681987
3 жыл бұрын
Very well explained sir...aap videos time to time upload krte rahiye....
@maxmendez7608
Жыл бұрын
You are showing a concept control called: Master in Air. You can take some advantage if you put the Temperature PID Loop governing GasFlowCtrl Valve instead of AirFlowCtrl Valve and the Air-Ratio PID Loop governing AirFlowCtrlValve instead of GasFlowCtrl Valve. THis type of control is called Master Fuel. Main advantage is a better response removing the delay for temperature loop. Remember, the delay is the "killer" for any control system. By the way, in the practical the orifice plate must be located upstream of the control valve to eliminate perturbation/uncertain measurement cause to modulating valve. Br.
@aforautomation
Жыл бұрын
correct,thanks for the valuable information
@JITENDRASINGH-hy9cm
3 жыл бұрын
Sir good for learning..
@sameermallick3341
2 жыл бұрын
Sir aapse aik request hai ki Anti surge valve kaise work karta hai aur kislie use karte hai,kab aur kaha use karte hai use karne ka kya benifit hai.
@RahulSingh-fz7sy
3 жыл бұрын
Sir aap drive to tensions control karne ke liye kon kon se parameters jaruri hote he us pr video banai
@anildarri2185
2 жыл бұрын
#anilautomationhindi 👍
@priyadarsanbarad1090
2 жыл бұрын
sir iski pid parameter program thoda logic dikhake explain kijiye
@shashitripathi978
2 жыл бұрын
Sir iska logic ke bare me video banaye
@shashitripathi978
2 жыл бұрын
Sir cold rolling mill ke electrical system ke bare me video banaye
@anildarri2185
2 жыл бұрын
#anilautomationhindi 👍
@MuhammadArslan-vl7ln
3 жыл бұрын
Sir Please make a video on PID in Delta PLC
@anildarri2185
2 жыл бұрын
#anilautomationhindi 👍
@Osm290
3 жыл бұрын
Sir plz upload more video related plc
@aforautomation
3 жыл бұрын
Sure i will keep uploading..
@Osm290
3 жыл бұрын
@@aforautomation sir special analog input qnd output Rtd module
@elseif7620
2 жыл бұрын
Sir mere pass fuji ka 10hp ka vfd hai mere pass ek regulated DC 540 volt ⚡ hai dusra dc solar ka jo un regulated Dc 400 se 680 tk jata hai agar dono voltage ko vfd k bus contector ko dena hai to kaise de dono dc se vfd load ko chalaye
@aforautomation
2 жыл бұрын
Solar wale voltage ko inverter laga k regulated wali supply k input me do, jisse ki always regulated dc milega usko vfd k dc bus me connect kar do
@deepakshukla7290
3 жыл бұрын
Sir please upload more videos furnace related
@supratimdey5
2 жыл бұрын
Very nice video But 1 question Why air needs to be master?
@aforautomation
2 жыл бұрын
Because in any closed furnace if there is no air then only gas can create explosion during ignition.and in lack of air gas will be wastage.
@kashimali2590
2 жыл бұрын
Sir please 🙏 tell me ufrom in up
@mukeshshah9607
2 жыл бұрын
Sir, What is value of A/F ratio for LPG ??
@aforautomation
2 жыл бұрын
its from 25-30
@rhsifat1337
2 жыл бұрын
Tnx a lot sir❤️ महोदय, मुझे आपसे कुछ कहना है।
@aforautomation
2 жыл бұрын
कहिए जनाब
@kashimali2590
2 жыл бұрын
Sir aap kaha se hai
@kashimali2590
2 жыл бұрын
Please 🙏 tell me
@rhsifat1337
2 жыл бұрын
A lot of love I am Bangladeshi❤️ I want to talk to you about some issues. Is there any means of communication?
@waqarkhakwani
Жыл бұрын
Hi Sir, currently i am facing this issue can i contact with you by whatsapp plz
@AmarKumar-hg4il
2 жыл бұрын
Sir mujhe aapse ek help chahiye fugi ace drive Ka please sir help me
@aforautomation
2 жыл бұрын
what help you need?
@AmarKumar-hg4il
2 жыл бұрын
Jaise if IC IE ye bhi to sir parameter wale function hai sir
@AmarKumar-hg4il
2 жыл бұрын
Iske bare me pura details chahiye kya aap mere wattsap par sir bat Kar sakte hai AUR mujhe plc scada Karna hai to aap sir mujhe bataye
Пікірлер: 53