Please Please Please make a video showing how to do this.
@chopsddy3
3 жыл бұрын
Thanks! Exactly what I’ve been looking for. Couldn’t ask for a better fit. BTW I have a Beeman 1336 Chief 2 Synthetic. I just bought a Umarex Gauntlet magazine to see if it would work in it , and it does! The Gauntlet magazine works in both the Air Venturi Avenger AND the Umarex Origin, so this mod should work for all four rifles. It seems that these bolts and receivers are being sourced from the same manufacturer. Thanks again for the heads up. Finding the right o rings can be a real pain.
@cc23001
Жыл бұрын
Yeah, bolt and receivers are made in the same factory. Also, they all use a "Marauder style" magazine from Crosman's design
@billycosby1435
Жыл бұрын
Can you leave the original o-rings on and cover it with the shrink tube, or will it not seal correctly when the probe is inserted?
@webreakforsquirrel4201
3 жыл бұрын
I solder nearly all my electrical connections. So I always have surplus heat shrink. Marine heat shrink has like hot glue inside and the wall thickness of the tubing is greater than standard heat shrink. It could be more durable.
@robert7984
3 жыл бұрын
Yes sir. I'll never use anything else again. This solution is pretty foolproof and talk about steady FPS. I recently got 3 chrony doups in a row. I've had 2 a lot of times but 1st time I've had 3 in a row.
@webreakforsquirrel4201
3 жыл бұрын
@@robert7984 did you remove the probe to install it?
@robert7984
2 жыл бұрын
@@webreakforsquirrel4201 sorry for the late reply man! I rarely get notifications on this channel. But no, I just slid it in lol.
@AirGunnerrr
2 жыл бұрын
Great Video Man.... 😎
@natesolomon4796
2 жыл бұрын
Thanks! Very informative
@Fernando_Woolybooger
2 жыл бұрын
I'm confused. You cut two smaller bands and put in o ring groove and then covered entire bolt, or did you leave the o rings on and then cover with shrink or did you take o rings off??
@robert7984
2 жыл бұрын
I took the rings off. Ill be doing a video in the next couple of days. It will show everything.
@wadedeeds1738
2 жыл бұрын
My question exactly. Or cut shrink for groves where O Rings went. Then cover probe.
@billreynolds2766
2 жыл бұрын
Have you done the back up video?
@ychongy
8 ай бұрын
Did this ever get answered?
@Fernando_Woolybooger
8 ай бұрын
No. @@ychongy
@numizaairguns1373
3 жыл бұрын
Great 👍
@andrewmiller9265
2 жыл бұрын
Sweet thanks for the tip sir
@alienairguns
2 жыл бұрын
I noticed that three edge of the barrel beach is sharp and I think that's what's tearing up the orings. I ton a half moon needle file and put a light lead in the beach. Let's see how it holds up.
@wadedeeds1738
2 жыл бұрын
Thanks. Do you cut a piece of heat shrink for O Ring groves heat them first, then heat shrink over it all. Thanks in advance.
@fernandogaraygorta2223
2 жыл бұрын
do you remove de oring ? or is still there under the thermo.tubing?? thanks great solution !!
@jwhitaker81
5 ай бұрын
Someone is making a killing off of selling little chopped up pieces of 3/16 small engine fuel line for $10 each, LOL! I ordered one of these kits and compared to said fuel line that can be obtained from Advanced Auto by the foot for a few dollars and it's identical in every way. Save yourself some money, make 5 or so "O-ring delete kits" and still have line left over to repair your gasoline weed eater.
@BombsAwayMineCraft
Жыл бұрын
Yeah my original o rings only lasted about 3 weeks
@Fernando_Woolybooger
2 жыл бұрын
what do yo mean by two smaller bands?
@johnm7414
2 жыл бұрын
Do you pull the pellet probe out the back to perform this?
@robert7984
2 жыл бұрын
No I just slip the cut pieces of tube over the end and press them on before hitting with heat.
@vamonosdecaceria5005
2 жыл бұрын
Puedes disparar con el cargador no le impide El Paso
@joverton8522
3 жыл бұрын
Do you remove the existing O rings!?
@robert7984
3 жыл бұрын
yes. the 2 small cut strips will fill in the o-ring channel.
@joverton8522
3 жыл бұрын
@@robert7984 THANKS!
@robert7984
3 жыл бұрын
@@joverton8522 No problem Be sure to use couple drops of silicone oil for the break in. It'll feel a little stiff the first few mags but this is a good thing...its basically custom sealing to your specific barrel.
@joverton8522
3 жыл бұрын
@@robert7984 THANKS AGAIN!!
@rossfrid3159
3 жыл бұрын
Which tubing do you use? Source?
@robert7984
3 жыл бұрын
I used this www.amazon.com/gp/product/B08HJ13SFC/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
@rossfrid3159
3 жыл бұрын
@@robert7984 Which size?
@robert7984
3 жыл бұрын
@@rossfrid3159 only one fits. you will know.
@ponz924
2 жыл бұрын
@@robert7984 In your video the heat shrink appears clear. You linked to black heat shrink?
@donniefoster7713
2 жыл бұрын
Did you remove the probe from the gun to install that are just slide on and heat up?
Пікірлер: 40