Omg I can’t give Chris a much better name! This man has sorted my katran out for myself honestly 1 in a million!!!
@tomwilkins3099
Жыл бұрын
Thanks Chris this is a welcome instruction video 👍 Cheers Tom
@MonchisAirguns
Жыл бұрын
Thank you for your video brother, I will make one in Spanish for my Latino friends, thank you very much
@AirMaksarmsUK
Жыл бұрын
Your welcome! I have corrected the english subtitles, perhaps there is a way to add spanish ones?
@eddieevans9612
Ай бұрын
I would like to see a video on swapping sides of the safety, I’ve already swapped the cocking lever to the right and would like to have the safety on the same side, thanks
@airshootist
Жыл бұрын
thanks for providing!
@AirMaksarmsUK
Жыл бұрын
My pleasure!
@henrymoreland8719
Жыл бұрын
Thanks Chris.
@AirMaksarmsUK
Жыл бұрын
Sorry it took soo long to get it up
@stedyone1090
Жыл бұрын
Thanks for sharing
@AirMaksarmsUK
Жыл бұрын
Thanks for watching!
@mikeyb9819
10 ай бұрын
Hi Chris, great video. I’m waiting to take delivery of the Krait L from Range and Country. I intend fitting it with an Arken Zulus night vision scope. Can you tell me if the Krait’s scope rail can be easily reversed (fitted back to front)? I’m thinking that it’s built in 20 MOA coupled with the Zulus’ 30 MOA will be too much to correctly center the reticle.
@56Gumball
Жыл бұрын
Some of the small screws are Torx fittings on the latest Kraits, not Allen keys.
@AirMaksarmsUK
Жыл бұрын
To my knowledge the only Torx bolts used are for fixings not adjusters, such as the side plate, which adjusters do you have with Torx?
@56Gumball
Жыл бұрын
@@AirMaksarmsUK Torx are fitted to the cheek piece adjusting screws, the large side plate under the cheek piece and the plates either side above the cocking lever. There may be more, but I haven't deep stripped the gun.
@AirMaksarmsUK
Жыл бұрын
@@56Gumball Hi Bill, we have Torx on the same places except the cheek piece adjuster, the side plates and ones near cocking handle are fixings so Torx is used, unusual about the cheek piece adjuster tho
@AlexAirguns
Жыл бұрын
Fantastic!!
@arnoldtm31
Жыл бұрын
Hi Chris, thanks for the video. Do you know if the transfer port size is the same in FAC models and the sub 12 ?
@AirMaksarmsUK
Жыл бұрын
Transfer ports are specific to calibre and barrel length, for example a sub 12 .177 Krait needs a much larger one than a .22 Krait L and there are multiple lengths, calibres and power output options, each with a slightly different size
@MrRockstar1968
3 ай бұрын
How do you remove and separate the baffles?
@tirodeportivoavilez9908
Жыл бұрын
Hello, i have the same KRAIT, but my arm has a problem with the regulador. I don't know why my regulator is not analogic but is the same KRAIT. Can You help me with something? please.
@AirMaksarmsUK
Жыл бұрын
I can certainly try to help, what seems to be the problem?
@bacolod50
Жыл бұрын
what is that valve adjustment near the trigger linkage?
@AirMaksarmsUK
Жыл бұрын
Exhaust Valve tensioner, increasing it will shorten the time that the valve is open per shot, by default they leave the factory at minimum tension, mostly used for fine tuning things
@bacolod50
Жыл бұрын
@@AirMaksarmsUK thank you
@scubajeeper1
10 ай бұрын
Does the bottle have a valve in it, can you unscrew it without losing the air in it?
@AirMaksarmsUK
10 ай бұрын
Not by default, we have a valve kit accessory available to make it detachable which comes with 1 rifle mount and two bottle valves so you can hot swap bottles in the field
@phillipmendiola2100
7 ай бұрын
To increase pressure is clockwise and decrease pressure is counter clockwise , correct ?
@AirMaksarmsUK
7 ай бұрын
Hi, this is an old video, the instructions only relate to original design regulators, younger guns with Huma Regs are opposite direction, I recommend watching my newer video about tuning these
@phillipmendiola2100
7 ай бұрын
@cdrguns thanks that's what I thought just got a new 25 cal Krait X slug edition from Utah airguns👍
@bacolod50
Жыл бұрын
can you show us a video on how to install the single shot magazine pls. i already ruined one .
@AirMaksarmsUK
Жыл бұрын
Hi, I am not sure what you mean by this, the single shot loader simply slides into the breech like the multishot magazine does, the only issue I can potentially see if you were trying to use an older Katran version instead of the newer Krait and Katran version as the older ones are not compatible with Krait rifles
@better-than-some
Жыл бұрын
What digital pressure guage are you using Chris?
@AirMaksarmsUK
Жыл бұрын
Hi Simon, that is a chinese copy/oem of the huma one, its not a bad bit of kit in some ways but the refresh rate of the screen is pretty slow, when you take a shot it will drop down over 3 or 4 screen changes, then go back up over a few screen changes, the reality is that the reg has finished cycling long before the screen finishes displaying, handy if you want to set a really specific pressure like 52 bar, but afterwards.... just kind of chunky gimmick
@better-than-some
Жыл бұрын
@CDRGuns thanks so much Chris, is the gauge thread metric or imperial?
@AirMaksarmsUK
Жыл бұрын
@@better-than-some standard 1/8th BSP, you will need a dowty at the top or to transfer the seal from the original gauge but fitment is a doddle
@better-than-some
Жыл бұрын
@CDRGuns Chris you are a superstar, thank you
@MrRockstar1968
Жыл бұрын
Have all Krait got the digital regulator gauge?
@AirMaksarmsUK
Жыл бұрын
No that was just a temporary fitment to illustrate the change in pressure as small changes would not show up on camera very well using the analogue gauge, I personally dont rate those particular gauges as the display is too slow
@MrRockstar1968
Жыл бұрын
@@AirMaksarmsUK Yeah I don't like the digital pressure gauges either. Do you have any footage showing the replacing of the Krait regulator?
Пікірлер: 42