This aiwa draws 17kWh of mains power a month in standby mode. That's a lot. So I made a modification that reduces it significantly. Check it out: kzitem.info/news/bejne/0pt4znxqjYJ8qmUfeature=shared
@marcelopereyra9529
Жыл бұрын
Me guatria consultarle algo la regulación del sfr 401 y el sfr 402 a cuántos ohms lo debo regular para que quede bien ?
@djijspeakerguy4628
Жыл бұрын
This was the highest end stereo of it’s time from Aiwa. I have the speakers from the newer flagship unit, which are labeled SX-NA902. They look exactly like the SX-NA702 speakers, but with the components from these. (Paper center of cone (dust cap) instead of plastic.) They also say made in USA, but the internals are made in China, so I guess they were just assembled in the USA? If you ever need to get into the speakers to restore anything, there are two little slots on the bottom between the plastic front and particle board box, which can fit a flat screwdriver. The front panel is pressure fit on, and a slight amount of adhesive is applied to the pins from the factory, though it just fits together tightly so the glue is not needed.
@banellone
Жыл бұрын
Thank you for the info.
@GalaxianGamer
5 ай бұрын
I bought NSX-K765 in 1999 when i was teenager, got it new and now i will use your guide to restore it :-) thank you
@hsccarvalho8554
Жыл бұрын
Esse Nsx 999 Mk2 é um dos melhores aparelhos já feito pela Aiwa. Esse modelo é simplesmente fabuloso e sua manutenção ficou excelente.
@MarioRossi-xo6im
Жыл бұрын
Honest congratulations man, you have been very meticulous and careful in the repair. BRAVO!!! 👍🏻👍🏻👍🏻
@Ema-ic1zl
Жыл бұрын
Exelente restauracion! Sos un genio. Tengo uno guardado en su caja original en su caja desde 2005. Este video me va a ayudar a restaurarlo. Esos equipos son increibles. Felicitaciones. Abrazo desde Argentina
@Primorskiy72
11 ай бұрын
Пора доставать Aiwazavra! Пусть соседи ощутят мощь и рык! И проверьте как кнопки работают и лазер? Просто хранение в коробке вредно для конденсаторов, надо иногда включать, прогревать, проветривать! Ждём! )))
@elbblopez5453
2 жыл бұрын
Bien hermoso ese modelo 😍, excelente trabajo 👌👍 estimado
@jhonwick4064
2 жыл бұрын
Excelente trabajo amigo quedó como nuevo recién salido de fábrica . También lo are con el mío así . Buen trabajo amigo 👌👌👌👌👏👏👏👏
@DeniceCarlaGordon-kd1kg
Жыл бұрын
I have an Aiwa stereo 3, CD's Change radio powerful sound amplifier dual cassette listener and recording from 2008 and still sounds amazingly well
@banellone
Жыл бұрын
Pre 2000's equipment was made to last. These days it's all about make it last until the end of warranty as precise as possible.
@Primorskiy72
11 ай бұрын
Отличная работа! Молодёжь учитесь! )))
@davidpritchard9829
Жыл бұрын
Great video. Loads of useful pointers and it really is a FULL restoration! Although I would have liked to know what the subtitles say, there's enough in the video to understand what is going on. I have the Aiwa Z-M2700 and couldn't find much about it but seeing this, I realise that many of these Aiwa systems are virtually identical. Certainly the stripping down and servicing of the mechanics and pulleys gives me all the information that I need. My CD changer keeps popping out and the twin tape decks no longer work but I know what to do now! Great detail and I'm hopeful that given the time and care that you used, I will be able to get mine back to working order! Keep up the good work.
@Leandro82le
Жыл бұрын
Que belo trabalho, parabéns!
@paulolopesfernandes8192
4 ай бұрын
Aqui no Brasil esse modelo é o NSX-2200. Eu tive um.
@banellone
3 ай бұрын
Ovaj je isti, samo malo manje snage.
@khristian1973
Жыл бұрын
Hermoso, paciente y meticuloso trabajo. Felicitaciones! Gracias por compartirlo.
@Primorskiy72
11 ай бұрын
Как надо любить это дело! )))
@martin.333
2 жыл бұрын
Excelente video! me sirve para reparar mi Aiwa NSX 999. Gracias!
@banellone
2 жыл бұрын
Gracias a ti también.
@Riga_Style
2 жыл бұрын
Y alguien tiró el 999 a la papelera en perfecto estado solo que sin panel de control y la retroiluminación no funcionaba 🤗🤗🤗
@jhonwick4064
2 жыл бұрын
Yo también mi 999 👌👌👏👏
@rexa19
4 ай бұрын
tengo un aiwa NSX-999 tiene dos display y el de arriba se ilumina menos, esta tenue en varios sectores que podrá ser?? ya cambié los dos capacitores de la fuente de los 27v.. también resoldé todos sus pines pero sigue igual... esos display tienen vida util?? o sea se gastan y no tienen solución??? puede ser eso?? gracias!!
@banellone
3 ай бұрын
Ti VFD displeji ako predugo rade vremenom potamne. Kratkoročno rešenje je da se dovede nešto veći napon na grejač displeja, pa će biti svetliji, ali se znatno skraćuje vek trajanja.
@rexa19
3 ай бұрын
@@banellone Muchas gracias Banellone!!!
@DeoclezioGomes
Жыл бұрын
Muito bom gostei muito 😳👍👍👏👏👌😁👋🇧🇷🇧🇷
@Fernando_Frutuoso
2 жыл бұрын
Excelente!! Tenho um igual, HR japonês. Também fiz a restauração. A única coisa que fiz a mais, foi polir a bandeja, onde tem atrito plástico com plástico, o que a torna abrasiva fazendo enroscar. Mas sua manutenção foi fenomenal!!! Parabéns!! Fernando 🇧🇷
@banellone
2 жыл бұрын
Obrigado cara, excelente dispositivo.
@rodrigozajac2637
Жыл бұрын
Oi Fernando, onde voce mandou restaurar? pode me passar o contato? obrigado
@rodrigozajac2637
8 ай бұрын
oi @Fernando_Frutuoso onde vc arrumou o seu por favor?
@halfben7991
4 ай бұрын
Você poderia ter aproveitado e trocado os dois capacitores que aumentam o brilho do display ficaria com brilho melhor
@altoaudio3049
2 жыл бұрын
Impecable te felicito,!!buen detalle del led en la compactera
@ДмитрийСтонога
Жыл бұрын
Браво Мастеру!
@Primorskiy72
11 ай бұрын
Аплодисменты, стоя!👏 )))
@panagoskakatosis5314
7 ай бұрын
my aiwa model nsx 999 ml ii is stand by ok with screen open lights and now wehn i press the power on to open is open for one second and close no power. remain to stand by,,,wat can be the problem ?? i change allready the amfitrel 4131 and i chek the capacitors in the main board.. only one smol resistror o found burn and is smol size start color from left side first color is bronw second black orange green and last right side again bronw slim eny help frends/??
@shanthamurthysangipagi9277
11 ай бұрын
I have same sound system, now it is not functioning where can I repair and update… let me know please
@ivanrc1749
Жыл бұрын
Te felicito por ese trabajo podrías contarnos cula es el. Líquido q aplicas con el spray del tarro pequeño. Es algún alcohol o como se llama.. Gracias por compartir
@banellone
Жыл бұрын
Es WD40
@Primorskiy72
11 ай бұрын
@@banellone Подумалось тоже и точно! Хотя после, может ещё спиртом полить )))
@iqbalsingh-l2z
9 ай бұрын
i love the way you repaired it awesome sound quality and nice look can you parcel it to me
@MikailAbassov
5 ай бұрын
Я бы сейчас Любые деньги отдал бы МАСТЕРУ чтобы он обслужил мою АЙВушку
@TuTaDJOficial
2 жыл бұрын
Very good work, i have the same Aiwa
@banellone
2 жыл бұрын
Great system. Thanks!
@jorgediaz-hs9er
3 ай бұрын
Que sonido ...por dios!!!!!! Estos equipos son unicos..en mundo. .......
@mdsathyanarana8103
Жыл бұрын
Sir pleas my system is not working please repeat pl
@rexa19
9 ай бұрын
Muy bueno el video gracias! Como hace para que cambie de color la luz de arriba de la bandeja de cds.???
@banellone
9 ай бұрын
Instead of original led, i soldered changing color led connected directly to power supply over resistor so it runs 24/7
@_Sliderz
2 ай бұрын
Wow very Impressive job sir! How long did this restoration take? I’m inspired to follow this video as I have the same model (nsx999mkii) with the same issues, cassette decks, CD player and dull/ dim lighting on the display and no spectrum graphics. Please can I ask where is the best place to find the components/ parts for this? Thanks
@banellone
2 ай бұрын
@@_Sliderz Thank you. It took me around 3 days, but no rush, I enjoyed. You need only basic components, so it's best to look up in your local electronics component store.
@j.m.pearson7116
Ай бұрын
Really enjoyed the video. I've have a question. I've have an Aiwa NS-50 that I replaced the belts for the dual cassette players. But now I have no sound out of any of the speakers! I've double checked the connections and everything seems good. Any ideas?
Ola pessoal! Estou a procura de um técnico para fazer a troca dos capacitores 107 108, mas não encontro na minha região. Alguém na bahia ou região metropolitana que saiba fazer manutenção no som aiwa?
@tinaandrade7024
2 жыл бұрын
Conseguiu encontrar? Preciso concertar o carrossel do cd, e outras manutenções, moro na região metropolitana também.
@KarlosGrado
Жыл бұрын
Increíble trabajo
@Primorskiy72
11 ай бұрын
Aiwa возродилась! )))
@DouglastobiasBernabe-gk9fe
7 ай бұрын
Donde esta ese taller yo tengo un aiwa 999no sirve las caseteras
@Mohamedkrami
12 күн бұрын
ساعدتني كثيرا في ترميم و إصلاح جهازي من نفس النوع لكن من ماركة أخرى... قمت بنفس خطواتك تماما و الجهاز عاد ليشتغل من جديد و ولد ليعيش من جديد لمدة أطول.. محبتي و شكري الجزيل.... ❤️🇲🇦
@banellone
12 күн бұрын
Drago mi je da sam pomogao. Pozdrav!
@panagoskakatosis5314
10 ай бұрын
my dream for all life i was in germany wehn i se this new model cristimas time around 1991 year then i love so much i was working one month to buy that i remeber like is now 999 DMARK WAS THE PRICE FROM MEDIA MARK..IT WAS MY BEST CRISTIMAS PRESEND TO MY SELF... then after years stop working i give to some greek servis men hi fix for 3 days then stop working again,, then i found another one second head from ukrania and i have till now...the buton of console not works but i make the jop with control head.. super video nice jop..
@banellone
10 ай бұрын
Thanks for sharing with us. I was a little kid when my father bought it, and loved it so much since. I thought it has CRT inside back then. I believe this 999MkII was in production 1995.
@sinisaradosevic6794
Жыл бұрын
Gde mogu pronaci i poruciti flert kablove gumice dek.za muzicku liniju AIWA NSH SZ 35.. Beograd,Novi Sad i bliza okolina.. Odlican video..👏👏
@banellone
Жыл бұрын
belielektronik.rs
@mirza2648
2 жыл бұрын
Prelijep stub svaka cast.
@banellone
2 жыл бұрын
Hvala!
@janbaca6075
9 ай бұрын
What are you doing in 7:26?
@freedom5658
Жыл бұрын
Can you tell me what's the name of the song on 31''08?,I like it very much! pls let me know
@banellone
Жыл бұрын
Don't remember. It's from youtube's audio library.
@LexaBenger
6 ай бұрын
Perfekt video,THANKS 😉
@ОлегФабрицкий
11 ай бұрын
Наебужил со светодиодом🎄🎄🎄😀
@carlospanch6789
2 жыл бұрын
Yo tengo este sanyo modelo 1980 en perfecto estado que nunca necesito reparación, 42 años funcionando a pleno: kzitem.info/news/bejne/z6ZstqKMkHecnWU
@danielh3693
Ай бұрын
For sale?
@RudiSantoso-rt6qb
4 ай бұрын
Mantap Sodara....di Indonesia belum ada Restorasi begini...👍👍👍
@Anonymous-ed4th
4 ай бұрын
Excellent man
@UdayKhatri
Жыл бұрын
Amazing.... I have similar music player. AIWA 3 CD changer, radio working but CD and Tap stopped working a long time ago due to non use... can you help to make it working ??? I live in INDIA - Ahmedabad city. thanks uday
@banellone
Жыл бұрын
All help is in the video. Thanks.
@Primorskiy72
11 ай бұрын
Внимательно смотрите видео )))
@ЮрийКоваль-ю6ш
Ай бұрын
Да, мастер молодец!! Круто!! Отличная работа!! Браво! Всё очень аккуратно и понятно показано! У меня Aiwa nsx - 520, внешнее состояние - отличное, очень бережно относился, но нужна чистка и смазка, иногда заедает карусель, похоже пасики нужно менять, да и конечно, это не удивительно, аппарату 29 лет. Звук - прекрасный ! Хороший дизайн! Великолепие ретро, сейчас таких не делают! А жаль!!! Многие современные аппараты в сравнении с этими, могут просто тихо курить в сторонке! У меня обширная коллекция винтажной техники, всё в рабочем и отличном состоянии, и я могу уверенно говорить о качестве и звучании аппаратуры прошлых лет! Тех самых лет, когда нужно было " держать марку", когда действительно работали конструкторские бюро, электронщики, дизайнеры.... Ведь даже от одного вида , очень приятно общение с этой техникой, да, и опять же - звучание!!! Сказка из прошлого, класс!!
@pablo_mtb4130
Жыл бұрын
23:22 did you use a 9v battery... to check the laser?
@banellone
Жыл бұрын
No, I used my power supply, about 1V.
@Chrisangel2000
Жыл бұрын
Hi, I need your help, i have the same model. My didn't read Disc. I fix it but when i put everything back together, it does turn on by for a bit, then it turns off by itself. Can you tell me what I Did wrong. Please, Thank You.
@marichusalanga4257
Жыл бұрын
How I wish my Aiwa NSx F9 will also be restored. Some of the buttons are not operational. The led display is blurred. And if connected to dvd player, the sound is distorted.
@Shamsithaca
7 ай бұрын
oh why didnt they put any cooling fan inside?
@banellone
7 ай бұрын
No need. Higher power output model has it. nsx2200.
@ramanaraomandava6771
9 ай бұрын
Good Veadio
@albertavaloti7273
Жыл бұрын
Hola yo tengo comprado 00 km , y los botones cuando aprieto hace otra funcion que no le correspone y el lector CD a veces lee y otras no.....le he llevado a varios técnicos y siempre viene con la misma falla. No dan la solución
@Primorskiy72
11 ай бұрын
Решение в этом видео! Если лазер не заработает, то замена, там KSS-210A, берегитесь подделок, оригинал стоит около 10$ )))
@danielhauff2156
Жыл бұрын
for a long time I have been looking to buy this aiwa model with 2 speakers and a remote control, or with a set of surround speakers
@kylevox-cn8zf
Жыл бұрын
Can you recommend anywhere in the UK that does this kind of restoration?
@ramanaraomandava6771
9 ай бұрын
Good job
@Kopro_Skulo
9 ай бұрын
good evening my friend fantastic video i have exactly the same model and it doesn't open the CD door either from the button or from the remote control😢
@banellone
9 ай бұрын
No worries, it's very possible just rubber belt.
@Kopro_Skulo
9 ай бұрын
@@banellone thank you my friend but it's very strange, last time the CD door opened by pressing the button to open the device and since then it never opened again
@mbam9068
Жыл бұрын
Hola sabes tengo uno igual pero no me sintoniza fm pero am si sabés que podría ser gracias
@banellone
Жыл бұрын
Tienes en el manual de servicio cómo ajustar la sección FM.
@antonioaugusto4833
10 ай бұрын
O Mk2 ficou top demais né cheff Abraço !!!
@martinrodriguezsilva5264
11 ай бұрын
Me pondrían sacar de una duda cual es mejor el nsx520 o el nsx999
@Primorskiy72
11 ай бұрын
999 )))
@Doc5555
Жыл бұрын
Друг ты просто божественно дотошен обожаю, когда люди так относятся бережно к технике и так её ремонтируют🎉🎉🎉🎉браво, это было, конечно, шикарное восстановление. У меня точно такой же 1 в 1-я его тоже отдал человеку на восстановление.
@Primorskiy72
11 ай бұрын
И как восстановление? Жива ли Айвушка? )))
@Doc5555
11 ай бұрын
@@Primorskiy72 Да друг мой ещё как,правда родная голова не всегда стабильно работает,но это не беда потому что закзал новую она пришла уже на выходных мастер установит)) На старой работает всё переключает,но есть несколько но,когда делаешь громко лазер сбивается причём колонки друг от друга на расстоянии больше 1.5 метра стоят и от головы тоже ,когда переключаешь с 1 на последнюю песню голова глючит и скидывает на начало подстройка резистора не особо помогла. Кнопки кстати тоже поменяны работает как новый дисплеи ярче яркого ))
@Primorskiy72
11 ай бұрын
@@Doc5555 Отлично! Лазер вероятно сел немного или пыль под линзой в шахте, это трудно почистить, но регулировка регулятора тока луча обычно помогает, но крутить надо длинной плоской отвёрткой через задние вентиляционные прорези задней стенки, от заводского положения не более 10 градусов, обычно вправо, но не обязательно, может и влево, бывает двигать надо очень мало буквально по полградуса, градус и проверять читаемость и стабильность на хороших фирменных дисках и тогда ещё походит! При значительном превышении тока луча, лазер скиснет за несколько десятков часов, учтите! Головка там как правило KSS-210A, надёжная, но на неё много подделок за 5$! Нужен хороший поставщик, Я брал на Али у HK KeMeiDa Laser, Kerun Technology, Angibabestore в разные годы, цена около 10$. У хороших линза обычно с синим покрытием, у дешёвок прозрачная. Вибрации от АС можно уменьшить, наклеив снизу резиновые ножки из упругой, пористой проминающейся резины резины, эффект есть, проверено! T-BASS лучше не использовать или не более одной ступени, BBE с кассет две или одна ступень, с CD не использовать. Процессор эффектов тоже не нужен, всё отключить и эквалайзер по нолям! Тогда она поёт, правильно и красиво, если надо качнуть, то качнёт! Но громкость не ставь выше 80 процентов, береги Айвушку! ))) Держи нас в курсе ремонта! Удачи! )))
@Primorskiy72
11 ай бұрын
@@Doc5555 Если не слушаешь, отключай полностью от сети, дольше проживёт экран и блок питания! )))
@Primorskiy72
11 ай бұрын
@@Doc5555 Подвесы НЧ динамиков смазывай раз в месяц жидкостью Platenclene, в течении года, звук на басах станет помягче, ибо уже они подзадубели немного, ей же протирать ролики прижимные с небольшим усилием, чистит и умягчает резину очень хорошо! Спиртом ролики не тереть, сушит резину! Спиртом только головки, но не магнитным пинцетом! И тонвалы держи в чистоте. Дека там довольно хорошего качества для воспроизведения, звучит мягче CD, ламповей )))
@bertiidol76
Жыл бұрын
In the practice this never happens!!!! Aiwa its trash.
@lovepreetsinghgill517
8 ай бұрын
Very nice, you turned it like a NEW.
@shakilahamed1455
Жыл бұрын
What the out put voltage⚡ transformers?
@Йордан-г6х
Жыл бұрын
ЛАЗЕР-SD капут, процесор - капут, усилвател и тонколони👍🏻
@rahmat0248
11 ай бұрын
Aiwa 😱
@MrDzoni022
Жыл бұрын
Druze imam istu aiwu. Dali mozes da mi resis taj problem?
@maunguyenvan5552
Жыл бұрын
Sửa máy kĩ quá vậy mới tốt
@АндрейКислов-ы3ю
11 ай бұрын
Приветствую аудио доктор. Я сам так-же реставрирую.999.939. Sony 881. Каких только небыло. Салам из Бишкека.
@dhanunjayathanugula8440
2 жыл бұрын
Sir repair my aiwa sound system
@1980vasy
Жыл бұрын
Очень познавательное видео. А подскажите как почистить линзу лазера не прибегая к такой сложной разборке и как разобрать колонки. Спасибо.
@hawkism
Жыл бұрын
Id love another one of these hifis
@mustafaonurucak614
Жыл бұрын
Hello, first of all, take it easy. I have aiwa nsx s223 model stereo music set. But the cd player and cd changer parts of the device do not work in any way. Why do you think it might be? Thank you from now.
@banellone
Жыл бұрын
Hello. It might be broken flat cable connections or slipping drive belts.
@sretkouric3774
2 жыл бұрын
svaka čast,odlican posao,trebao bih malo podeiti brzinu pri reprodukciji kasete,mozes li mi reci gdje se to podesava,pokusao sam na motoru ali ne ide,ako moze odgovor,hvala!
@banellone
2 жыл бұрын
Ima trimer na pločici desnog deka. Na pločici je rupa gde možeš da gurneš šrafcigerčić. On bi trebalo da je za oba deka, jer na pločici levog deka nema trimera. MEĐUTIM, ako si stavio nove gumice, šire, onda se poremete odnosi remenika, pa jedan radi brže, drugi sporije i trimerom bi dodatno poremetio brzinu. Tako da samo ako su gumice identične, onda trimer.
@sretkouric3774
2 жыл бұрын
@@banellone da,mijenjao sam gumice,nisu original,vjerovatno je to razlog,hvala na odgovoru!
@u0j0u
Жыл бұрын
Hi excellent restoration and very helpfull video!! Looking at the thoroughly job you did on it perhaps you can help me. I did a similar job (not as deep) on an AIWA NSX-AVH80 that looks very similar, particularly the dual cassette deck (FD-NH80) are alike. Everything worked fine, but I found that the tape capstan motor and all flywheels are constantly running, even with the power is off (st by mode), they start when the power cord is plugged in. My question goes if yours does the same or the motor stops in certain point. I would really appreciete any advise on this. Thank you very much in advance.
@banellone
Жыл бұрын
Hi, mine work just fine. It looks like some transistors for the motor got shorted and puts out power non stop. Since standby is not really standby because all voltages are present in the system. Watch my standby mod video for nsx999mk2, it might be helpful to understand how standby isn't really standby.
@ericfobi276
Жыл бұрын
Is it possible to get a telephone number to call to restore my Aiwa mini shelf audio system?
@Primorskiy72
11 ай бұрын
Учитесь по видео сами! Ничего трудного, внимательность и аккуратность! )))
@doctorpetrovich9296
2 жыл бұрын
i was only 13 when aiwa mini component system came out me and my dad bought aiwa nsx999
@banellone
2 жыл бұрын
Beautiful memory. I was seven, still remember the feeling.
@danielb.5166
Жыл бұрын
HOLA A MI ME PASA QUE SI QUIERO CAMBIAR DE EQUILIZADOR SE CAMBIA EL COMANDO A CUALQUIER COSA PASA A CD O AUXILIAR O AVECES SE APAGA. POR QUE HACE ESO ES X ESTAR SUCIO POR DENTRO ?
@banellone
Жыл бұрын
Mira el video otra vez
@Primorskiy72
11 ай бұрын
Командный процессор реагирует на сопротивление цепей от кнопок, кнопки окислились, сопротивление сильно возросло, идут ложные команды, Aiwa закупила у плохого поставщика, лет после десяти кнопки выходят из строя. Кнопки можно реанимировать, но шанс мал, около 200-500 грамм нажимая с некоторым усилием на каждую, раз сто в день, процедуру повторять, до тысячи нажатий на каждую в общей сумме, если не поможет, то замена, кнопок, как в этом видео! Соблюдайте аккуратность или обратитесь к опытному мастеру! Кнопки новые с Али вероятно будут сильнее щёлкать, как в видео, но это нормально! Периодически если замените кнопки, пользуйтесь ими всеми делая на каждую не менее 50 нажатий в месяц, тогда вероятность окисления упадёт! Удачи! )))
@sreckosabolic0863
Жыл бұрын
Može broj tefona ili da mi se javiš tražim muzicku liniju isti ako je imaš pravimo poso
@banellone
Жыл бұрын
Nisam vlasnik uređaja. Pozdrav!
@likelike8707
2 жыл бұрын
opt ima slike nema tona 😂😎
@CrazyMade
2 жыл бұрын
Awesome
@milevucic8662
2 жыл бұрын
Fenomenalno
@banellone
2 жыл бұрын
Hvala!
@khushalchawla3713
Жыл бұрын
Good work
@golotud2050
2 жыл бұрын
A+
@aanandreassudiro8375
2 жыл бұрын
Hello Salom.
@ЛюбомирЗоря
Жыл бұрын
Неймовірно! Дякую!
@Osmanov.82
Жыл бұрын
IDEALLE ANLAGE KLASIK
@claudiodean6363
2 жыл бұрын
Good Job !!!!
@mototymkarvina9009
2 жыл бұрын
what are they used there flexible cable FFC FPC ???
@banellone
2 жыл бұрын
FFC only
@mototymkarvina9009
2 жыл бұрын
@@banellone 1mm 8 pin?
@SixtoRavelino
Жыл бұрын
hermoso equipo cuantos watts tiene ese aiwa por saber
@banellone
Жыл бұрын
2x160W
@jabedshikdar6364
Жыл бұрын
STK IC number??
@banellone
Жыл бұрын
Don't remember. Search for service manual.
@Mr_Flybacker
Жыл бұрын
STK4231
@Primorskiy72
11 ай бұрын
STK4241 аналог, но мощнее на 20 Вт )))
@matrix6132
2 жыл бұрын
Svaka cast za klip steta sto si daleko ja imam za opravku jedan vhs plejer tj mozda samo podesavanje tonske glave posto se bio utisao ton ja sam cistio alkoholom samo nisam znao da se ona tri mala srafa sto je drze ne diraju pa sam cacno i poremetio tracking i sada ne mogu da podesim.Inace vhs rikorder je samsung 2003 godiste.Kupio sam ga radi prebacivanja kaseta na kompjuter.Ovde kod mene vec nemam kome da odnesem na zalost.
@banellone
2 жыл бұрын
Hvala. Pogledaj kanal 12voltvids. Ima dosta videa o VHS plejerima.
@willianschottperrud7881
2 жыл бұрын
O melhor
@АлександрКуслиев-й8у
Жыл бұрын
Здравствуйте у меня такая же айва не светится экран что может быть?
@banellone
Жыл бұрын
Здравствуйте. Kонденсаторы с107 и с108 нужно заменить.
@ramkirankalla1306
2 жыл бұрын
I brought the same music system in 1996, when I was studying my Engineering and we had great time with this music system partying and was quite popular with my friends in college. I love this system, so I still kept it. But it's not functioning any more. The cassette mechanism is not engaging, CD is not working and the buttons on the panel respond differently, like if I press CD button it may do something else. I have the schematics, I tried fixing it, but was not able to fix it, I guess the Microcontroller got corrupted. Please suggest me any repair solution.
@banellone
2 жыл бұрын
I suggest you to watch full video. It's most likely that your faults are the same as in this unit.
@ramkirankalla1306
2 жыл бұрын
@@banellone I already watched the full video, I don't understand the captions, as they r not in English. I will try cleaning all the contact switches in cassette mechanism, if it works, I will try changing all the push buttons. thanks for the reply.
@banellone
2 жыл бұрын
@@ramkirankalla1306 It's only matter of cleaning switches with contact cleaner, changing belts and replacing tactile switches on mainboard. Majority of job is assembling and disassembling with extra caution, especially laser unit. Good luck.
@ramkirankalla1306
2 жыл бұрын
@@banellone Thank you for the reply, I will try and check
Пікірлер: 221