Thank you so much for taking the time and energy to make these videos for no obvious reward. I'm very grateful. Your channel is full of great stuff.
@TCsAnythingGoes
2 жыл бұрын
Thanks for your compliment. I am trying to grow the channel to a point where it becomes a sustainable income for me. Also cause I really like learning and sharing knowledge.
@rasidsungkaiful
8 ай бұрын
Thank you Brother... very much appreciated...
@merlin1346
11 ай бұрын
Very useful video bro, love all things Vellfire 😎👍
@TCsAnythingGoes
11 ай бұрын
thanks for the compliment bro. More videos to come soon.
@adharuddinabd.rahman4521
2 жыл бұрын
Bro! TQVM for the very insightful/useful video. I am thinking to remove the left side 2nd row seat (to install welcab seat). From your video, I was keen about everything until the cable get cut. Would that cause trouble as if I want to put the pilot seat back in the future? I'm worrying connected cable might not be as strong as the original single piece, or the length might get shorten/lengthen so the future installation moght not be as firm as original?
@TCsAnythingGoes
2 жыл бұрын
Actually, you can make do without cutting the cable. There is a socket and a bolt that holds it to the seat. Just unplug the socket and unbolt it and u are good to go. I didn't do it this way cause I didn't want that white plastic socket getting in my way earlier.
@Yolizi
8 күн бұрын
Hi bro you said 66 inch length empty space after folding 3 th. Row seats ,168cm,my height is 180 cm so I can not put mattress and fit,is there any possible way to fold second row seats or it is not foldable like 3 th row seats?
@muhammadsafwan9382
3 жыл бұрын
So many changes including u bro.. haha..by the way, nice house n keep up good content bro!
@robdennis3721
Жыл бұрын
How do you remove the tracks afterwards from this sliding guides
@TCsAnythingGoes
Жыл бұрын
Ohhh i didn't remove the tracks. If you own an Alphard 10 series, its easy cause the bolts are on top. But 20 and 30 series Alphards have their bolts on the bottom of the car. You will need to loosen your exhaust and fuel tank to get access to them.
@guyburns9154
2 жыл бұрын
Very helpful!
@user-ln2hs6yv9r
Жыл бұрын
Hi guy. I'm watching from Thailand. I need some help from you. Would you recommend me how to change a cup holder on the mid row seat. Thank you.
@TCsAnythingGoes
Жыл бұрын
you mean the cup holder/table in between the two chairs at the mid row? Or do you mean the cup holder that is attached to the seat armrest.
@pchan8127
9 ай бұрын
Hi, great video, 1 question: Can you fit a sleeping mattress behind the 2nd row seats? Without removing the 2nd row seats? Thank you.
@TCsAnythingGoes
9 ай бұрын
Yes you can. I fitted a Queen size inflatable mattress there before.
@andrewmcintyre7692
6 ай бұрын
Tysm this is so kind
@TCsAnythingGoes
6 ай бұрын
You are most welcome.
@freddyfujii7207
Жыл бұрын
Good morning TC😊 I need a advice regarding how to take out the cigarette lighter socket from a AH-20. I’ve tried but it seems tough….😢 and quick and easy way to do it.? Thanks
@TCsAnythingGoes
Жыл бұрын
Just gotta remove the radio panel and you have access to the back of the cigarette lighter socket.
@freddyfujii7207
Жыл бұрын
@@TCsAnythingGoes thanks.! I’ll give it a try later tonight
8 ай бұрын
Hi, thank you very much. But do you know if I can fit (1+ 1 wide seat) to have 3 seats instead of 2 ( in my 2gen. Alphard) in the middle raw (as my family is growing)? That has become very important now. Thank you
@TCsAnythingGoes
8 ай бұрын
you will need to change the rails underneath and also get a 8 seater's second row for this. Not easy but doable.
@Skippy992
2 жыл бұрын
Hi I have the same vehicle don’t need to remove seat but am replacing blanking cover for Toyota part that is fitted to the non leather model seats that can slide from side to side you just need to replace existing part as cable mechanism is already there just not used but I am having trouble removing them side covers to access and fit new part willing to share photos of new part and no If you know of an easy way of removing them covers.
@TCsAnythingGoes
2 жыл бұрын
hit me up on FB TC's AnythingGoes Channel
@lazarbeam4253
Жыл бұрын
Hello, thank you for the video. Do you know if you can fit 10 series seats on the 20 series rails?
@TCsAnythingGoes
Жыл бұрын
No, its different mounts. I was exploring that as well just to get the mid row to turn backwards. =)
@lazarbeam4253
Жыл бұрын
Ah that's a shame. Nevermind will have to leave as they are. Thank you.
@mosalah9090
3 жыл бұрын
new house, new car..tahniah bro. what next? new wife? 😁
@TCsAnythingGoes
3 жыл бұрын
no new wife. Current wife good enough. Hehe. Thanks bro.
@TheNightKiing
5 ай бұрын
hey mate can these be the same from models from 2017 ( 3rd generation ) I watched your back row seats removal as well. Also can we remove the sliding metal where the seats attached to if Im wanting to convert my Alphard to an empty work van with the back seats removed and use as a work space.
@TCsAnythingGoes
5 ай бұрын
yes, its the same with the 3rd generation seats. Removing the rails on the 2nd and 3rd gen is pretty difficult. You have to jack the car up, loosen the exhaust system..... just to have access to the nuts underneath.
@TheNightKiing
5 ай бұрын
@@TCsAnythingGoes cheers!
@sofahousechurch8266
2 жыл бұрын
Can these seat be refitted facing backwards?
@kahar_diy3955
3 жыл бұрын
Wah..so long til new video..new car?..niceeee..👍👍👍👍👍
@TCsAnythingGoes
3 жыл бұрын
yeah, took awhile. in the last two months, I only released like 3 videos. Internet here is bad and with the new house, been pretty occupied.
@dbtheproduction5701
9 ай бұрын
I'm planning to install pilot seat in anh20.. At the moment my car is 8 seater... How should I start
@TCsAnythingGoes
9 ай бұрын
first is find the pilot seat. then you need the rails and wiring as well. Will need to drill the floor pan in order to install the 7 seater rails.
@rafiqamustafarah1720
Жыл бұрын
tq for the video.. my middle seat have problem cannot move up and down.. any solution please
@rafiqamustafarah1720
Жыл бұрын
how can i cantact u
@TCsAnythingGoes
Жыл бұрын
@@rafiqamustafarah1720 you can add me up on my FB, TC's AnythingGoes Channel
@abumaleeha1
2 жыл бұрын
Can the middle seats be fitted other way around. So back of seat is touching drivers and passenger seat
@TCsAnythingGoes
2 жыл бұрын
hmmm..... from the looks of it... you can't cause the latch to unlock and lock the rollers are on one side only.
@Rob-md6ml
24 күн бұрын
Bro you don't need to cut the wires 🙈 just undo the 10mm nut that's on the white plastic part above and right of the one you undone and the whole wiring part just comes away from the seat and slides back. You don't need to undo the 10mm that you did, do the other one....no cutting
@TCsAnythingGoes
23 күн бұрын
yeah, i only realised that much later....... unfortunately.
@apaisigatbn
3 жыл бұрын
Have video on installing back n wiring?
@TCsAnythingGoes
2 жыл бұрын
Same way it was removed.... except it takes a lot more muscle and sweat to lift the chair up as opposed to lifting it down the car. =). Wiring wise, just attach connectors and connect them.
@ytubefams6368
Жыл бұрын
My middle alphard seats like yours are shaking when cruising in bad roads, how i can repair it ?
@TCsAnythingGoes
Жыл бұрын
if its shaking then there is a possibility that one of your bolts are loose. But if you are saying that it vibrates and makes a lot of noise, then you might want to take it out, flip it over and see what's loose.
@ytubefams6368
Жыл бұрын
@@TCsAnythingGoes thanks for advice, that's sounds lot of job to flip elephants baby 😂😂 i will try in next weekend
@Lukex29
2 жыл бұрын
Hey what about removing the rails left on the floor? They are sticking out.
@TCsAnythingGoes
2 жыл бұрын
To remove the rails, you will need to jack the car up, loosen the exhaust and fuel tank just to access the nuts that is holding the rails. I didn't do it cause I have no need to remove the rails at the moment.
@Lukex29
2 жыл бұрын
@@TCsAnythingGoesAh ok, it's just they are very prominent so if you wanted to sleep on the floor they could get in the way. Thanks
@Lukex29
2 жыл бұрын
@@TCsAnythingGoes That is crazy, wasnt it much easier in the first generation??
@TCsAnythingGoes
2 жыл бұрын
@@Lukex29 yes, the first generations have the bolts on the top so removing them was much much easier.
@elroycampbell
2 жыл бұрын
I noticed in this vid you don’t have any step carpet mats, are they hard to get there?
@TCsAnythingGoes
2 жыл бұрын
Not difficult just that I have not found one that suits my taste and budget.
@elroycampbell
2 жыл бұрын
@@TCsAnythingGoes I have a black set (1 for each door step) if you want. Just pay for shipping.
@raymunhong2076
2 жыл бұрын
Hi bro, do you have any idea to fix the mid row electronic chair button on the side? Mine were stuck already , can press lean up but cant to press lean dowb
@TCsAnythingGoes
2 жыл бұрын
you most likely need to replace the switch shopee.com.my/Genuine-Toyota-Alphard-Vellfire-ANH20-GGH20-2008-2014-Rear-Power-Seat-Switch-Lefthand-Side-i.141512155.4814505944?gclid=Cj0KCQjw_fiLBhDOARIsAF4khR0v0JaSrZBkLQuJGyfc7_WCf7gBskIZP9L5jahk4XUiOL7cg8DoTdMaAt3HEALw_wcB
@raymunhong2076
2 жыл бұрын
@@TCsAnythingGoes wow.. Not cheap tho. But bro, the thing is still function but just the button were stuck.. Is that necessary to change whole set?
@TCsAnythingGoes
2 жыл бұрын
@@raymunhong2076 you can try to dismantle the switch and see if the reason it is stuck is because of dirt and gunk. If it is, then its still fixable. But if its the return mechanism that is broken then the only way to fix is to replace.
@raymunhong2076
2 жыл бұрын
@@TCsAnythingGoes i see... Thanks for your info.. Great Video 👍🏻
@louisng2721
5 ай бұрын
do you have to disconnect the battery bro before removing?
@TCsAnythingGoes
5 ай бұрын
It is advisable to...... but if you are careful enough with the wires, you don't have to.
@marcelpannasch4810
11 ай бұрын
We're you get the floor Mats ?
@TCsAnythingGoes
9 ай бұрын
I wish I could answer that as well. Floor mats came with the car when I got it 2nd hand.
@Grzesztof01
Жыл бұрын
Can I connect usb charger for that seats?
@TCsAnythingGoes
Жыл бұрын
Connect a USB charger to the seats? Yes you can but wiring wise, you got two options. Connect to the wires that operates the seats (but this means the USB will be powered all the time as the wires are live even when the car is turned off ) or run a new positive from the fuse box. I was pondering on doing this but didn't proceed cause it means drilling a hole into the seat side cover to mount the usb plug.
@Grzesztof01
Жыл бұрын
@@TCsAnythingGoes Thank you for you answer.
@nasaaja6789
2 жыл бұрын
,👍👍👍👍👍👍
@tcaudiomute
2 жыл бұрын
broooo how the F u manage to remove the seat all by yourself ahahahha!
@TCsAnythingGoes
2 жыл бұрын
It was not easy....... heavy as an elephant.
@tcaudiomute
2 жыл бұрын
@@TCsAnythingGoes yeah man I did this car multiple times i know the struggle 😂
Пікірлер: 78