I wondered what went into doing this. After watching, it's not hard to do but I would definately keep buying new alternators due to the amount of time it takes. And, I don't have a press, good video!
@GorrillaFastTv
29 күн бұрын
Don’t need a press , harmonic balance puller works just ass good
@ToyManFlyer1100
Жыл бұрын
Hummmph...Nobody ever shows using the old bearing to push the new one back in....Inspiring!!!...👏👏👏🥂🥂👍👍👍💰💰💰
@carleynorthcoast1915
Жыл бұрын
I'm not sure if this alternator would work because at 10:04 he is using the inner race to drive in the outer race which causes damage to the bearing
@AwsBadr
Жыл бұрын
It will work. Would be better if he placed a metal piece to spread the pressure.
@benjaminzhou9503
10 ай бұрын
…. It seems to be a lady working on it, making the job even more admirable. Not sure though. The person was using the old bearing to drive in the new one. So didn’t need to worry about the old one getting ruined. I would put a thick piece of medal over it though, to push directly against the outer race on the new bearing’s outer race. Great video, very inspiring! Just need to make sure to use quality bearing, not all bearings are made equally well.
@chrisfort7340
6 ай бұрын
Well done! Thank you very much for your time and know how to make this video!😎👍
@dustyfruitypie1633
10 ай бұрын
What make of bearing do you recommend? Excellent video by the way
@stevenbean9706
2 ай бұрын
ordered a bearing puller i couldn't get the inner bearing off by simply prying it buying every tool imaginable so i dont get stuck when i rebuild the next one
@theakh4238
10 ай бұрын
Use heat on the aluminum housing, and support the backside of the bearing housing my dude. Its very easy to deform or even crack the alternator case pounding it the bearing out like that.
@ZutiDIY
10 ай бұрын
Thanks for the tip
@twinturboranch454
9 күн бұрын
where do you order your bearings?
@allthentikmusic5617
Ай бұрын
Can i call you i have some questions
@desimundavlog773
2 жыл бұрын
How to know a Pulley was good or bad ??can u explain it plz
@jesusp.7774
Жыл бұрын
The noise
@jerryfitz2002
2 ай бұрын
Good video but when you put a socket on to hit the bearing out without any support under it that bearing or housing will no longer be true. Gauge it and I bet it’s out of spec.
@andykim681
7 ай бұрын
This is such a great video. Thank you very much for your effort to show how to replace it. I have a question about the replacement. Can you tell my what are the bearing size and any website address i can get the bearing?
@corsaire2644
4 күн бұрын
Trop fort! Bravo !!!
@carllinden533
Жыл бұрын
I hope my Trabant 601 alternator is easier. I don't have a press
@constantinchivu583
6 ай бұрын
Greu fără presă
@39FORTYWATER
2 жыл бұрын
Thank you for demo
@Skandalos
9 ай бұрын
I wonder if I can do this without a press.
@michaeldavid3672
Жыл бұрын
Where can I buy the bearings and what part numbers?
@ZutiDIY
Жыл бұрын
Ebay
@Imran-gu6gs
Жыл бұрын
Good
@Dr.JHIrons
2 жыл бұрын
I’d just purchase a new alternator..
@vr6swp
2 жыл бұрын
For my car, a rebuild kit with bearings, brushes and a new back cap is about $40 plus an afternoon’s work. New alternator is about $150-$200 plus core charge (and shipping both ways). You decide whats best for you
@stevenjosephs9
Жыл бұрын
Right , Remanufactured are crap ( shit )
@jesusp.7774
Жыл бұрын
And sometimes the aftermarkets are weaker on amps
@peblum
2 жыл бұрын
Why not replace the pulley while you're rebuilding. Thanks for the video, I'm learning!
@donald8354
Жыл бұрын
If the pulley is good why replace.
@Dassick89
Жыл бұрын
Because they cost the same as a whole alternator lol.
@sultan26706
2 жыл бұрын
Perfect thanks
@videoworks7731
Жыл бұрын
thank you
@dennisshaw1195
2 жыл бұрын
Great job
@frankensteinrules6511
2 жыл бұрын
BEST VIDEO ON KZitem!!!!!!!!!!
@Surendarghorela
9 ай бұрын
Boss use gloves??????
@constantinchivu583
6 ай бұрын
Greu cu mănuși mai ales la lipituri colector și perii
Пікірлер: 39