STL Files: www.eclipson-airplanes.com/pi...
LW-PLA: colorfabb.com/lw-pla-natural
Thank you so much for watching!
If you like videos like this, consider buying me a coffee, it really supports me: www.buymeacoffee.com/troymcmi...
See what else I am working on: / troymcmillan_rc
www.tiktok.com/@troymcmillan_...
#3DPrinted,#RCAirplane, #ItFlies
Pitts S12 Parts:
SunnySky 2820 1100kv Motor: sunnyskyusa.com/products/sunn...
11x5.5 APC prop: amzn.to/3AFIA0V
60A ESC: amzn.to/3nwXJw1
ES08MA Servo: amzn.to/3ANk2mB
3S 2700mAh Battery:
4S 2200mAh Battery:
2x8mm Screws: amzn.to/3p8gmqY
10x5x3 Magnets: amzn.to/3bzb4Pz
1/8” Wheel Collar: amzn.to/3p4tvl1
3pin wire assortment: amzn.to/3l1xNYt
XT60 connector: amzn.to/3iyZWnf
2mm push rod ends: amzn.to/3nnjD4U
3D Printers I use and recommend:
AnyCubic Vyper: amzn.to/3AJqwTM
Artillery Sidewinder 3D Printer: amzn.to/396eqIp
Artillery Genius 3D Printer: amzn.to/39cA6CZ
Ender3 V2: amzn.to/2SmLOGk
Twotrees Sapphire-PRO: amzn.to/3wtNOLz
Anycubic Mega X Printer: amzn.to/3f4oS89
Fokoos Odin-5: amzn.to/3fAES06
3D Printing Filament:
ABS for motor mounts: amzn.to/3xgLI2c
ColorFabb LW-PLA: colorfabb.com/lw-pla-natural
ePLA-ST: amzn.to/3AGymgY
TPU: amzn.to/2Sw3Oe8
Tools and Supplies used:
Spektrum DX6 Controller: amzn.to/3l6NFsD
Spektrum NX10 Controller: amzn.to/3jnjvST
Receiver: amzn.to/3j4PbK4
Battery Charger: amzn.to/3vejwfL
Charge cable: amzn.to/34lOk3q
XT60 connector: amzn.to/3iyZWnf
Assortment of 3-Pin Extension Cables: amzn.to/3l1xNYt
Z-Bend pliers: amzn.to/34mA0rt
2mm push rod ends: amzn.to/3nnjD4U
CA Glue: amzn.to/2J8EvNW
CA Accelerator: amzn.to/3fpbycz
Low-Voltage Tester: amzn.to/2Yk0A0w
Hot knife: amzn.to/3nrCwUH
Drill Bits: amzn.to/3nIJzrx
Hobby Knife: amzn.to/3eYOYJq
#11 blades: amzn.to/3vTJZ2W
Z-Bend pliers: amzn.to/34mA0rt
Build Mat: amzn.to/3vJmauw
Onboard Camera: amzn.to/3rp2OrH
Lead weight: amzn.to/3cFnzeu
Print Settings:
Quality:
Layer Height - 0.25
Initial Layer Height - 0.15
Line Width - 0.4
Walls:
Wall Line Count - 1
Z Seam Alignment - User Specified
Z Seam Position - Back (Position part to align Z seam)
Seam Corner Preference - Expose Seam
Top/Bottom:
Top Layers - 0
Bottom Layers - 0
Infill:
Infill Density - 0
Material:
Printing Temperature - 235
Build Plate Temperature - 60
Flow - 55%
Speed:
Print Speed - 100
Outer Wall Speed - 55
Inner Wall Speed - 55
Travel Speed - 120
Travel:
Enable Retraction - Checked
Retraction Distance - 7.5mm (Bowden Tube Ender3)
Retraction Speed - 35mm/s
Retraction Extra Prime Amount - 0.2
Combing Mode - off
Cooling:
Enable Print Cooling - Checked
Fan Speed - 80
Mesh Fixes:
Union Overlapping Volumes - Checked
Special Modes:
Surface Mode - Normal
Experimental:
Slicing Tolerance - Middle
Music:
Song: Jarico - Landscape (Vlog No Copyright Music)
Music promoted by Vlog No Copyright Music.
Video Link: • Video
Music: Joakim Karud:
KZitem: / joakimkarud
Soundcloud: / joakimkarud
Music provided by Argofox:
From The Dust - Solar
• From The Dust - Solar ...
Music provided by Argofox:
Ghost'n'Ghost - Lighthouse
• Ghost'n'Ghost - Lighth...
Disclaimer: I am sponsored by some of the products I mention. However, all of my opinions are my own. Some of the above links are affiliate links, that does not effect the price you pay for a product, but I may receive a small commission if you make a purchase. This helps support my channel and allows me to continue to make videos like this. Thank you for your support!!
Негізгі бет Ғылым және технология AMAZING DIY Pitts S12 Full Build and Flight
Пікірлер: 136